TMC2130Stepper
TMC2130Stepper copied to clipboard
teemuatlut
Stallguard with AccelStepper Library
Hi, I want to use Stallguard and a Library to run the stepper such as Accelstepper Library. I've combined Stallguard example and Accelstepper example. Stepper is running but output is:
0 0 55 0 0 55 0 0 55
meaning that driver.DRV_STATUS(); return same value al the time. I've tried to put stepper.run(); inside ISR code, inside loop(). Also tried with conditional into ISR and into loop code, but still not load detected (stepper motor running withput problems).
Any ideas? Bellow the code used Regards Martin
/**
* Author Teemu Mäntykallio
* Initializes the library and turns the motor in alternating directions.
*/
#include <TMC2130Stepper.h>
#include <AccelStepper.h>
#include <TMC2130Stepper_REGDEFS.h>
#define EN_PIN 6 // Nano v3: 16 Mega: 38 //enable (CFG6)
#define DIR_PIN 4 // 19 55 //direction
#define STEP_PIN 5 // 18 54 //step
#define CS_PIN 10 // 17 64 //chip select
byte MOSI_PIN = 11; //SDI/MOSI (ICSP: 4, Uno: 11, Mega: 51)
byte MISO_PIN = 12; //SDO/MISO (ICSP: 1, Uno: 12, Mega: 50)
byte SCK_PIN = 13; //CLK/SCK (ICSP: 3, Uno: 13, Mega: 52)
#define MAX_SPEED 40 // In timer value
#define MIN_SPEED 1000
#define STALL_VALUE 0 // [-64..63]
constexpr uint32_t steps_per_mm = 80;
int dir = -1 ;
//TMC2130Stepper driver = TMC2130Stepper(EN_PIN, DIR_PIN, STEP_PIN, CS_PIN);
TMC2130Stepper driver = TMC2130Stepper(EN_PIN, DIR_PIN, STEP_PIN, CS_PIN, MOSI_PIN, MISO_PIN, SCK_PIN);
AccelStepper stepper = AccelStepper(stepper.DRIVER, STEP_PIN, DIR_PIN);
bool vsense;
uint16_t rms_current(uint8_t CS, float Rsense = 0.11) {
return (float)(CS+1)/32.0 * (vsense?0.180:0.325)/(Rsense+0.02) / 1.41421 * 1000;
}
void setup() {
{
Serial.begin(250000); //init serial port and set baudrate
while(!Serial); //wait for serial port to connect (needed for Leonardo only)
Serial.println("\nStart...");
pinMode(EN_PIN, OUTPUT);
pinMode(DIR_PIN, OUTPUT);
pinMode(STEP_PIN, OUTPUT);
pinMode(CS_PIN, OUTPUT);
digitalWrite(EN_PIN, HIGH); //deactivate driver (LOW active)
digitalWrite(DIR_PIN, LOW); //LOW or HIGH
digitalWrite(STEP_PIN, LOW);
digitalWrite(CS_PIN, HIGH);
SPI.begin();
pinMode(MISO_PIN, INPUT_PULLUP);
}
{
driver.push();
driver.toff(3);
driver.tbl(1);
driver.hysteresis_start(4);
driver.hysteresis_end(-2);
driver.rms_current(600); // mA
driver.microsteps(16);
driver.diag1_stall(1);
driver.diag1_active_high(1);
driver.coolstep_min_speed(0xFFFFF); // 20bit max
driver.THIGH(0);
driver.semin(5);
driver.semax(2);
driver.sedn(0b01);
driver.sg_stall_value(STALL_VALUE);
driver.stealthChop(1);
}
{
stepper.setMaxSpeed(50*steps_per_mm); // 100mm/s @ 80 steps/mm
stepper.setAcceleration(1000*steps_per_mm); // 2000mm/s^2
stepper.setEnablePin(EN_PIN);
stepper.setPinsInverted(false, false, true);
stepper.enableOutputs();
}
{
cli();//stop interrupts
TCCR1A = 0;// set entire TCCR1A register to 0
TCCR1B = 0;// same for TCCR1B
TCNT1 = 0;//initialize counter value to 0
OCR1A = 512;// = (16*10^6) / (1*1024) - 1 (must be <65536)
// turn on CTC mode
TCCR1B |= (1 << WGM12);
// Set CS11 bits for 8 prescaler
TCCR1B |= (1 << CS11);// | (1 << CS10);
// enable timer compare interrupt
TIMSK1 |= (1 << OCIE1A);
sei();//allow interrupts
}
digitalWrite(EN_PIN, LOW);
vsense = driver.vsense();
}
ISR(TIMER1_COMPA_vect){
if (stepper.distanceToGo() == 0) {
// stepper.disableOutputs();
//delay(500);
stepper.move(dir*1000*steps_per_mm); // Move 100mm
// stepper.enableOutputs();
//dir = dir*-1;
}
stepper.run();
}
void loop()
{
static uint32_t last_time=0;
uint32_t ms = millis();
while(Serial.available() > 0) {
int8_t read_byte = Serial.read();
if (read_byte == '0') { TIMSK1 &= ~(1 << OCIE1A); digitalWrite( EN_PIN, HIGH ); }
else if (read_byte == '1') { TIMSK1 |= (1 << OCIE1A); digitalWrite( EN_PIN, LOW ); }
else if (read_byte == '+') if (OCR1A > MAX_SPEED) OCR1A -= 20;
else if (read_byte == '-') if (OCR1A < MIN_SPEED) OCR1A += 20;
}
if((ms-last_time) > 100) //run every 0.1s
{
last_time = ms;
uint32_t drv_status = driver.DRV_STATUS();
Serial.print("0 ");
Serial.print((drv_status & SG_RESULT_bm)>>SG_RESULT_bp , DEC);
Serial.print(" ");
Serial.println(rms_current((drv_status & CS_ACTUAL_bm)>>CS_ACTUAL_bp), DEC);
}
}
I go the same output with accelstepper/stallguard! 0 0 55 0 0 55 0 0 55 Any solution?
Would be really interesting if someone could give a solution here. I have the same problem.
Going by the code above, stallGuard doesn't work with stealthChop. I'd also move the distance check out of ISR and remove the control characters for timer interval as you'd likely want that to be constant and let AccelStepper determine if a step needs to be taken or not.
Would be really interesting if someone could give a solution here. I have the same problem.
Me too! I would really appreciate if someone found a solution. :) Trying too get this done on teensy 3.2 – so I also have to rewrite the interrupts.
Hi guy, sorry for the delay. I've make my project work (curtain) checking distance using stallguard with stealthChop(0). After that I know the limits, I stop using stallguard and using stealthchop(1). The problem is if for some reason something block the curtain, the stepper will try to move the curtain all distance long making huge noise, but didnt happen yet.
@martinmatias could you post the working code please. I tried to do what teematlut suggested put it doesnt complile
@martinmatias Hello, I know this has been a while but is it possible for you to share with me the working code you have for the StallGuard?
https://github.com/teemuatlut/TMCStepper
/**
* Author Teemu Mäntykallio
*
* Plot TMC2130 or TMC2660 motor load using the stallGuard value.
* You can finetune the reading by changing the STALL_VALUE.
* This will let you control at which load the value will read 0
* and the stall flag will be triggered. This will also set pin DIAG1 high.
* A higher STALL_VALUE will make the reading less sensitive and
* a lower STALL_VALUE will make it more sensitive.
*/
#include <TMCStepper.h>
#define STALL_VALUE 15 // [-64..63]
#define EN_PIN 62 // Enable
#define DIR_PIN 48 // Direction
#define STEP_PIN 46 // Step
#define CS_PIN 53 // Chip select
#define SW_MOSI 66 // Software Master Out Slave In (MOSI)
#define SW_MISO 44 // Software Master In Slave Out (MISO)
#define SW_SCK 64 // Software Slave Clock (SCK)
#define R_SENSE 0.11f // Match to your driver
// SilentStepStick series use 0.11
// UltiMachine Einsy and Archim2 boards use 0.2
// Panucatt BSD2660 uses 0.1
// Watterott TMC5160 uses 0.075
// Select your stepper driver type
TMC2130Stepper driver(CS_PIN, R_SENSE); // Hardware SPI
using namespace TMC2130_n;
#include <AccelStepper.h>
AccelStepper stepper = AccelStepper(stepper.DRIVER, STEP_PIN, DIR_PIN);
ISR(TIMER1_COMPA_vect){
stepper.run();
}
void setup() {
SPI.begin();
Serial.begin(115200); // Init serial port and set baudrate
while(!Serial); // Wait for serial port to connect
Serial.println("\nStart...");
pinMode(EN_PIN, OUTPUT);
pinMode(STEP_PIN, OUTPUT);
pinMode(CS_PIN, OUTPUT);
pinMode(DIR_PIN, OUTPUT);
pinMode(MISO, INPUT_PULLUP);
digitalWrite(EN_PIN, LOW);
driver.begin();
driver.toff(3);
driver.intpol(true);
driver.blank_time(24);
driver.rms_current(400); // mA
driver.microsteps(4);
driver.TCOOLTHRS(0xFFFFF); // 20bit max
driver.THIGH(0);
driver.semin(0);
driver.semax(2);
driver.sedn(0b01);
driver.sgt(STALL_VALUE);
// Set stepper interrupt @ 800Hz
{
cli();//stop interrupts
TCCR1A = 0;// set entire TCCR1A register to 0
TCCR1B = 0;// same for TCCR1B
TCNT1 = 0;//initialize counter value to 0
OCR1A = 20000;// = (16*10^6) / (1*1024) - 1 (must be <65536)
// turn on CTC mode
TCCR1B |= (1 << WGM12);
// Set CS11 bits for 8 prescaler
TCCR1B |= (1 << CS10);
// enable timer compare interrupt
TIMSK1 |= (1 << OCIE1A);
sei();//allow interrupts
}
stepper.setMaxSpeed(800);
stepper.setAcceleration(400);
stepper.setEnablePin(EN_PIN);
stepper.setPinsInverted(false, false, true);
stepper.enableOutputs();
}
char buffer[128] = {0};
void loop() {
static uint32_t last_time=0;
uint32_t ms = millis();
if((ms-last_time) > 100) { //run every 0.1s
last_time = ms;
DRV_STATUS_t drv_status{0};
drv_status.sr = driver.DRV_STATUS();
sprintf(buffer, "%5lu %5u %4u %u",
stepper.distanceToGo(),
static_cast<uint16_t>(stepper.speed()),
drv_status.sg_result,
driver.cs2rms(drv_status.cs_actual)
);
Serial.println(buffer);
}
if (stepper.distanceToGo() == 0) {
stepper.disableOutputs();
delay(1000);
stepper.move(3000);
stepper.enableOutputs();
}
}
Many thanks. I am suspecting the reason why my code and setup is not working because I am using Bigtreetech tmc2130. I am getting the silentstepstick version and try again.
Hello, Thank you for your examples. It keeps me informed about TMCStepper. I tried the last example here. As seen in the graph, the speed first increases and then decreases. I want the engine speed to increase slowly and continue at full speed. How can I work on this issue? thank you.
Dear Fatih Elibol,
programming TMC driver has been two years ago for me.
If You now say "TMC", the only thing, I do, is subconsciosly shiver, because of the hustle I've had with it. However, best success, with Your project.
Best Greetings,
Malte Ernst
-----Original-Nachricht----- Betreff: Re: [teemuatlut/TMC2130Stepper] Stallguard with AccelStepper Library (#69) Datum: 2022-04-27T08:18:30+0200 Von: "Fatih Elibol" @.> An: "teemuatlut/TMC2130Stepper" @.>
Hello, Thank you for your examples. It keeps me informed about TMCStepper. I tried the last example here. As seen in the graph, the speed first increases and then decreases. I want the engine speed to increase slowly and continue at full speed. How can I work on this issue? thank you. — Reply to this email directly, view it on GitHub https://github.com/teemuatlut/TMC2130Stepper/issues/69#issuecomment-1110587372 , or unsubscribe https://github.com/notifications/unsubscribe-auth/ANXXIW3TXMOIGE5I47ORMKTVHDL2ZANCNFSM4GUJ3ZOA . You are receiving this because you commented.Message ID: @.> [ { @.": "http://schema.org", @.": "EmailMessage", "potentialAction": { @.": "ViewAction", "target": "https://github.com/teemuatlut/TMC2130Stepper/issues/69#issuecomment-1110587372", "url": "https://github.com/teemuatlut/TMC2130Stepper/issues/69#issuecomment-1110587372", "name": "View Issue" }, "description": "View this Issue on GitHub", "publisher": { @.***": "Organization", "name": "GitHub", "url": "https://github.com" } } ]
