Improve/Fix Daikin 10502 support

[trantuan4889]

Dir sir. I installed as a guide, HA can synchronize with Mihome, but can't control AC Daikin. I tried to control it with MiHome when I was suspended again, and after a few minutes I could control it with MiHome. Can you help me with the setting? I used acpartner.v3. Thanks

[syssi]

How did you setup the device at the mihome app? Did you learn every command individually?

[trantuan4889]

I installed according to Mihome app

configuration.yaml

climate:

• platform: xiaomi_miio name: Aqara Air Conditioning Companion host: 192.168.1.9 token: 0ef64eed2f627b6a7cdxxwerrw0d41aee2 target_sensor: sensor.temperature_158d0001fde1f10 scan_interval: 60

logger: default: warn logs: custom_components.climate.xiaomi_miio: debug miio: debug

and copy custom_components/xiaomi_miio to folder config and run.

[browntownington]

do you recommend learning the individual commands in the mihome app @syssi or going with a template that seems to work/fit?

[trantuan4889]

Have I done this already and is there any additional step needed to add the AC code? I check state in Hass, it show: climate.aqara_air_conditioning_companion off current_temperature: 29.6 min_temp: 16 max_temp: 30 temperature: 27 target_temp_step: 1 fan_mode: high fan_list: low,medium,high,auto operation_mode: off operation_list: heat,cool,auto,dehumidify,ventilate,off swing_mode: off swing_list: on,off,unknown ac_model: 010501870001050201 load_power: 0 led: true friendly_name: AC supported_features: 4801 But i can't control AC

Mihome just let me check the feedback from the air conditioner.

Thanks.

[syssi]

@trantuan4889 At first you've to make sure the acpartner.v3 + MiHome App works flawlessly. If this is the case you can try to control your AC with this component, too. If the MiHome App doesn't work reliable this component cannot improve the situation.

@browntownington I recommand a working template. I've no experience with learned commands. I'm afraid this component doesn't work out of the box with a learned command set.

[trantuan4889]

I sure the acpartner.v3 + MiHome App works flawlessly. But i can't control my AC. When i setup control parameters on HASS, Mihome show parameters as HASS but AC is not controlled. ( HASS on only control turned on AC, cannot be turned off AC) I control AC by Mihome is ok.

Vào Th 4, 6 thg 3, 2019 vào lúc 13:58 Sebastian Muszynski < [email protected]> đã viết:

@trantuan4889 https://github.com/trantuan4889 At first you've to make sure the acpartner.v3 + MiHome App works flawlessly. If this is the case you can try to control your AC with this component, too. If the MiHome App doesn't work reliable this component cannot improve the situation.

@browntownington https://github.com/browntownington I recommand a working template. I've no experience with learned commands. I'm afraid this component doesn't work out of the box with a learned command set.

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/syssi/xiaomi_airconditioningcompanion/issues/48#issuecomment-469992420, or mute the thread https://github.com/notifications/unsubscribe-auth/At8fXnhOjFuhFsPZLZDx-exHG7kbcAbiks5vT2cpgaJpZM4bbuCO .

[syssi]

How did you configure your AC at the MiHome App? Did you choose a template or did you learn some commands by pressing some buttons of your remote control? I assume your AC isn't supported properly.

[trantuan4889]

I choose a template AC at Mihome. Type Daikin 10502. https://upanh1.com/image/IVpHim https://upanh1.com/image/IVpD2X

[syssi]

Interesting. Could you try to set a target temperature via Home Assistant. Does your AC accept/acknowledge this change? May be just turning the AC off is broken.

[trantuan4889]

Oh. I change a target via Home Assistant, AC not acknowledge this change but Mihome displayed the right target. (HASS on only control turned on AC, cannot be turned off, temperature, fan, swing...) I change a target via Mihome, AC accept this change.( Mihome can control full function AC)

P/s: I check state in Hass ac_model: 010501870001050201 same Daikin 10502.

[trantuan4889]

I have controlled my air conditioner with new component. Thanks you very much. You can send me a tutorial to add some control commands to other devices after running the service learning command.

Vào 15:05, T.4, 6 Th3, 2019 Sebastian Muszynski [email protected] đã viết:

Interesting. Could you try to set a target temperature via Home Assistant. Does your AC accept/acknowledge this change? May be just turning the AC off is broken.

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/syssi/xiaomi_airconditioningcompanion/issues/48#issuecomment-470008415, or mute the thread https://github.com/notifications/unsubscribe-auth/At8fXik07e2LIs4xAzmWoBHTfhHjoPQ9ks5vT3a9gaJpZM4bbuCO .

[tzm112]

我用新组件控制了我的空调。非常感谢你。在运行service learning命令后，您可以向我发送一个教程，以便向其他设备添加一些控制命令。Vào15：05，T.4,6 Th3,2019 Sebastian Muszynski [email protected]đãviết： ... 有趣。您可以尝试通过Home Assistant设置目标温度吗？您的AC是否接受/确认此更改？可能只是将AC断开了。 - 你收到这个是因为你被提到了。直接回复此电子邮件，在GitHub上查看< ＃48（评论） >，或将线程静音< https://github.com/notifications/unsubscribe-auth/At8fXik07e2LIs4xAzmWoBHTfhHjoPQ9ks5vT3a9gaJpZM4bbuCO >。

hello i have same problem witch you. bug i have upgrade the componet to the new version.but still can no control。do you still use the syssi's componet? sorry for my poor english

[syssi]

I would like to improve the Daikin 10502 support. @trantuan4889 do you like to provide some testing?

[trantuan4889]

Yes I am always ready, Daikin 10502. Pls improve 10502 and 9357 :) I change code Daikin 10502 to Daikin 9357, I think 9357 can control fan swing or Fan mode only (Daikin 10502 not used)

[trantuan4889]

Hi syssi! Pls fix components, i updated HA to version 0.100.3, i can't connect web my home. I delete your components, and setting in configuration.yaml, it is ok. P/s: components xiaomiplug is error when check config. It show error version miio is old. Thanks

[syssi]

Did you updated the component, too? It should bei 0.100.3 compatible.

[trantuan4889]

yes, i down new version component, it same. I checked the HA log file running to this section and stopped running. I waited so long still. This is log with component. home-assistant(with component).log

This log after delete component, it is ok. home-assistant.log

[trantuan4889]

I update version Home Assistant 0.101, your component is ok :)

[ngdaihoc]

@trantuan4889 : I have some issues about the synchronizing between remote control Daikin and KTBL11LM (lumi.acpartner.v3), Can I discuss more with you? my email [email protected]