Can you make the same for Escam pt202????

[carlosvelosa]

Can you make the same for Escam pt202????

[roleoroleo]

I don't know. If it's based on the same platform, I could try. Please, take some pictures of the board.

[carlosvelosa]

Sorry for the time. I took pictures from the board.

[carlosvelosa]

This camera have SV6255P chip and the board is B102QP KB V1

[carlosvelosa]

The interior board have qg2101b and xmc chip

[carlosvelosa]

Another thing the firmware is 9.0.41.99_202103111513

[roleoroleo]

Ok. Probably the hack already exists. But... create a dump of your fw and share it with me: https://github.com/roleoroleo/yi-hack-Allwinner-v2/wiki/Dump-your-backup-firmware-(SD-card)

[carlosvelosa]

https://www.sendspace.com/filegroup/kEnw16yfVGY25i77A6znhArwi3RpIkhpcl%2BlXrNVYHagmEbOtZYkVMl1%2BsAZ2cLRSDLDjoUCqnanfnysLGohQw

[carlosvelosa]

There you have, i think all you need

[carlosvelosa]

mtd (1).txt

[roleoroleo]

Try b091qp, it should work. https://github.com/roleoroleo/yi-hack-Allwinner-v2/discussions/249#discussioncomment-1378470

[carlosvelosa]

Tente b091qp, ele deve funcionar. # 249 (responder no tópico)

It's working!!!! Fantastic, thanks @roleoroleo :D. This hack is the same on Escam pt202

[carlosvelosa]

ALL WORKING :DDDDDDDDDDDD

[roleoroleo]

I will add to the next release.

[roobbb]

Hello. I even bought one and hacked it successfully. It works very well. Thank you very much! One question: does the performance advice even apply to this device?

[roleoroleo]

One question: does the performance advice even apply to this device?

Yes, It's the same cpu/ram architecture.

[kirch-cam]

I have an almost identical (unbranded) model, the only difference is the wifi module Main board: QG2101b and xmc chip B102QP KB V1 board has Realtek chip instead of SV6255P. The Realtek wifi chip is marked 8188FTV KCF03G1 GK53Q1 Firmware is 9.0.41.99_202103301400 I assume they use the wifi module just as a serial modem, so the b091qp should work?

[roleoroleo]

I don't know if it works. Send me a backup copy and I will check.

[kirch-cam]

LINK REMOVED

[roleoroleo]

It's different from other supported b091qp. I could try to support your cam but I need some time.

[kirch-cam]

Thank you very much. That would be great.

[GqSteve]

@carlosvelosa Is the hack working also, when the cam is connected through the network interface?

[carlosvelosa]

@carlosvelosa Is the hack working also, when the cam is connected through the network interface?

Yes it's working without problems @GqSteve

[GqSteve]

@carlosvelosa I set up one with WiFi. I connected the camera per wire and disabled the WiFi AP. The cam is not requesting any IP from DHCP over the wired connection. How can I get it working? Btw, if the wired connection is going to work, how can I disable the WiFi on the cam?

[roobbb]

@GqSteve I started with LAN first and had to pair my cam with my LAN via the app. But was not able to connect it to Wifi. Therefore I paired my Cam again with Wifi via app. Both connections are working fine since. My Cam has two MAC-ID's and separate IP's. Maybe you could get it work with LAN if you try to pair your Cam with LAN too. This "Cable" option is very small and easy to miss Maybe it's worth a try 😀

[GqSteve]

My bad...the network interface supports 100M port speed...my port was fixed to 1000M...grrrrr But I can confirm that the hack works! Thanks!

[napalmpt]

Hi. I have one of these cams that somehow got bricked. it now only lights up the led and stays like that. I followed instructions for soft recovery, converted the backup mtdblock4.bin into backup_b091qp but didn't work. I tried to find the rs232 pads, but no luck or nothing happens on boot... should I return it?

[orion131313]

@carlosvelosa Is the hack working also, when the cam is connected through the network interface?

Yes it's working without problems @GqSteve

@carlosvelosa Yi YoT android app still working? Are there any better apps?

[kirch-cam]

It's different from other supported b091qp. I could try to support your cam but I need some time. @roleoroleo have you had a chance yet to support it?

[roleoroleo]

Yes, I think it's possible. Please, send me 3-4 copies of the file /dev/shm/fshare_frame_buf

[stale[bot]]

This issue has been automatically marked as stale because it has not had recent activity. It will be closed if no further activity occurs. Thank you for your contributions.