FT991A-PAT
FT991A-PAT copied to clipboard
rfrht
Gain very bad
hello,
Thank you for this project, great work, I like the integration in the FT-991A. I realized the S revision with the BRF193F, but I have a gain problem. The gain is around -20db, I changed the BFR193F but the same.
I tested in the FT-991A but the attenuation is too high with IPO or AMP1 the signals are almost invisible with AMP2 I see the signals.
Do you have an idea of my problem? Is the new BFR193F transistor not suitable?
Thanks. 73.
Hello @F4HZA o/
I have not tested the Revision S yet - this is the reason that I didn't promote it to the Main branch.
After consulting my digikey and JLCPCB orders, I found that I ordered the parts but never ordered the board - last known good revision is R.
When I get back to São Paulo (I'm in holidays here) I'll check my parts inventory and if all is sound, order a new board revision.
Side note, I found that this BFR193F is... tiny. Will be a pain to solder it; the 2SC5086 was already a challenge.
You might also want to check this reddit thread where I was suspecting that the BFR193F wasn't a suitable choice (spoiler alert: it seems it was the right choice).
Expect to have the Rev. S tested by mid March. Will keep this issue open for the time being.
Hello there @F4HZA !
Stopping by to let you know that I ordered the parts and the board this weekend - and will probably have all the ducks lined for testing in January!
Good morning, Sorry I moved on to another project, I made myself a panadaptor with an SPF5043Z and the basic schema. No switch, the FT-991A automatically switches to ground, no filter. I am very happy with it. I made a PCB with HF connectors, and placed it in the FT-911A since January 2023. I use an SDRPlay the gain is positioned at 1 in the SDR console program. The important thing is to correctly configure the IF Output in External Radio, something capricious.
Thank you for your project which allowed me to install a panadaptor.
- F4HZA
Hello, Frederic! Thanks for sharing the SPF5043Z, I checked its datasheet - and the automatic bias control is definitely a relief.
I built a board design that allows for a SPF5043 for testing, will put that on my future tests. Thank you very much for sharing!
So- how's your board working? Do you have any pictures to share?
Hi,
I didn't take a photo of the mounted card, here is the image of the PCB.
I did it the old fashioned way, copper plate and iron perchloride. The components are quite large and soldering is easy. I have attached the EAGLE project. Panadapter EAGLE with SPF5043Z - F4HZA .zip The card works perfectly, it was installed in January 2023 I have not reopened the FT-991A since. I use it with the SDRPLAY PRO2.
A point to review would be the 78L05 which heats up a little. Certainly also the adaptation of the values of the components I do not have the equipment to analyze. Make a professional PCB and resize it for good integration. I had some problems correctly configuring the SDR CONSOLE software with the "External RADIO" and IF OUTPUT . 73. FAHZA.
Hey there @F4HZA !
I finally built the test board, based on the experimental Revision S. Two major problems:
- The RF switch is flipped :-P It is disconnected by default - and this is the wrong logic. I have to fix that.
- I found more or less what you found. While the loss wasn't that much you found, it is a non-neglectible -7 dB.
I ran a VNA sweep from 10-1000 MHz and found that the board performs reasonably well around 200ish MHz - wich makes me believe that the BFR193 is under heavy impedance mismatch at ~ 70 MHz (the S21 Marker 1).
I'll do some experiences here, and keep this issue open for the time being. I would like to thank you very much for the initial test and for reporting this issue!