rtl8188eus
rtl8188eus copied to clipboard
quickreflex
This driver does not support the monitor mode
Could you implement this case so that monitor mode support works, at least for Kali Linux. The chip I have is RTL8188EUS, and wifi is a usb wifiagent card. Here it is: http://4pda.ru/2016/11/21/329596 or here you can see: https://remo-zavod.ru/katalog/communication-antennas-and-equipment/antennas-wifi/antenna-wifi-agent . I will be very grateful! Generally did this instruction: [](https://forums.kali.org/showthread.php?37911-Getting-RTL8188-to-work-with-Kali-in-monitor-mode , but the kernel headers are not suitable. Here is the conclusion of airmon-ng:
root@debian:~# airmon-ng
PHY Interface Driver Chipset
phy0 wlan0 iwlwifi Intel Corporation Wireless 7265 (rev 61)
phy1 wlan1 ?????? Realtek Semiconductor Corp. RTL8188EUS 802.11n Wireless Network Adapter
#uname -r
4.15.0-kali3-amd64
# uname -a
Linux debian 4.15.0-kali3-amd64 #1 SMP Debian 4.15.17-1kali1 (2018-04-25) x86_64 GNU/Linux
And if you put this driver: https://github.com/lwfinger/rtl8188eu, the output of airmon-ng will be as follows:
root@debian:~# airmon-ng
PHY Interface Driver Chipset
phy0 wlan0 iwlwifi Intel Corporation Wireless 7265 (rev 61)
null wlan1 r8188eu Realtek Semiconductor Corp. RTL8188EUS 802.11n Wireless Network Adapter
root@debian:~# airmon-ng start wlan1
Found 3 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to run 'airmon-ng check kill'
PID Name
623 NetworkManager
740 wpa_supplicant
787 dhclient
PHY Interface Driver Chipset
phy0 wlan0 iwlwifi Intel Corporation Wireless 7265 (rev 61)
null wlan1 r8188eu Realtek Semiconductor Corp. RTL8188EUS 802.11n Wireless Network Adapter
root@debian:~# iw dev
phy#1
Interface wlan1
ifindex 4
wdev 0x100000001
addr 00:13:ef:81:01:8f
type managed
txpower 12.00 dBm
root@debian:~# iw list
Wiphy phy1
max # scan SSIDs: 9
max scan IEs length: 2304 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* monitor
* P2P-client
* P2P-GO
Band 1:
Capabilities: 0x1862
HT20/HT40
Static SM Power Save
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT Max RX data rate: 150 Mbps
HT TX/RX MCS rate indexes supported: 0-7, 32
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps
* 5.5 Mbps
* 11.0 Mbps
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm) (no IR)
* 2472 MHz [13] (20.0 dBm)
* 2484 MHz [14] (20.0 dBm) (no IR)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* set_bss
* join_ibss
* set_pmksa
* del_pmksa
* flush_pmksa
* remain_on_channel
* frame
* set_channel
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
WoWLAN support:
* wake up on anything (device continues operating normally)
software interface modes (can always be added):
* monitor
interface combinations are not supported
Device supports scan flush.
And now when switching to monitoring mode shows such an error
Error setting channel: command failed: Operation not supported (-95)
The driver in this mode does not work at this stage. I need to change a large amount of code to work. I can try, but it will take a long time.
yes, if you could remake the driver under monitor mode, I'm sure that I would be grateful to you not only for me! After all, this is the most common problem for this manufacturer. Almost all Realtek chips do not initially support the monitor mode out of the box. But still the decision is yours!
I found a solution for this mode. It turned out that the error was somewhere in the airmon-ng code. So in this case the interface should be start manually: ifconfig wlan1 down iwconfig wlan1 mode monitor ifconfig wlan1 up
And now you can start the program in monitor mode: airdump-ng wlan1
The drivers doesn't support virtual interface, that's why airmon-ng won't work and it has to be set in monitor mode manually.
Hi, I'm new to this. my Kali kernel is 4.17. I get only auto mode by doing: ifconfig wlan1 down iwconfig wlan1 mode monitor ifconfig wlan1 up It can not do deauth. :(. any help, please?
I think this issue can be closed? Maybe a separate issue tracker for virtual interfaces?
a mi me presenta este error al querer activar el modo monitor de forma manual ┌──(root㉿kali)-[~] └─# ifconfig wlan0 down
┌──(root㉿kali)-[~] └─# iwconfig wlan0 mode monitor Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; Invalid argument.
Alguien tendra alguna solución..?
Prueba esto: sudo iw dev wlan0 set type monitor
-------- Оригинално писмо --------
От: MelmacCode @.***
Относно: Re: [quickreflex/rtl8188eus] This driver does not support the monitor mode (#1)
До: quickreflex/rtl8188eus
Изпратено на: 10.11.2022 02:40
a mi me presenta este error al querer activar el modo monitor de forma manual ┌──(root㉿kali)-[~] └─# ifconfig wlan0 down
┌──(root㉿kali)-[~] └─# iwconfig wlan0 mode monitor Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; Invalid argument.
Alguien tendra alguna solución..?
—
Reply to this email directly, view it on GitHub , or unsubscribe .
You are receiving this because you commented. Message ID: @ github . com>