Bluefly protocol

[dc59]

Can it be possible to add Bluefly HP100 protocol ? this protocol is supported by Deviation. https://www.deviationtx.com/wiki/supported_models Thanks！

[dc59]

My fault, move to Discussions.

[pascallanger]

I can give it a try if you are still interrested.

[dc59]

Hi Pascal, Thanks for reply and yes I’m very happy to try it , if you can help.

Best regards, Dan

pascallanger @.***>於 2023年10月30日 週一，下午10:52寫道：

I can give it a try if you are still interrested.

— Reply to this email directly, view it on GitHub https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/issues/819#issuecomment-1785389792, or unsubscribe https://github.com/notifications/unsubscribe-auth/AEVOIMACQNQXEB3IBR72ZCTYB65LXAVCNFSM6AAAAAAUZBD3M6VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTOOBVGM4DSNZZGI . You are receiving this because you authored the thread.Message ID: @.*** com>

[pascallanger]

Please test the BlueFly protocol available in v1.3.3.36 located here https://downloads.multi-module.org/latest-test/

[dc59]

Thanks Pascal for your work. I tried it with RM TX12 / EdgeTX 2.8.1 / external 4 in 1 multi-module, it can bind to Bluefly HP100BL but only few second, the red led go solid when I bind, and then all servo go upper position or bottom position and led gose off (it seems lost bind), then I can't do anything! if you need video , please let me know.

[dc59]

I have tried freq. tune and it dosen't work.

[pascallanger]

Please test the version 1.3.3.37 same location which should be available in the next 5 minutes (auto build in progress)

[dc59]

I can't download test build due to error message as below.

" Error 404 – Not Found Artifact 'multi-test-build' not found for run #6831147439.

Check on GitHub: https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/actions/runs/6831147439#artifacts

Return to the home page "

[dc59]

Hi Pascal, I downloaded source code and compiled it with Arduino IDE get this file "multi-stm-1.3.3.37.bin" , flash this FW into 4in1 module, it get some result as 1.3.3.36!

[pascallanger]

There is only one place in all the files where the version is written so if the scripts has generated the file "multi-stm-1.3.3.37.bin" then if you upload it correctly to the radio it will show 1.3.3.37 . It just can't display anything else! Here is the result from the automated build: multi-test-build.zip Please report

[dc59]

Hi Pascal, Thank for uploading new 1.3.3.37 FW, but I'm not lucky, it worked as same as 1.3.3.36, after bind and servo move, then lost binding.

[pascallanger]

Can you control the servos or not at all ?

[dc59]

Not at all, after servo movement LED goes off (looks like lost bind) , I can't control anything.

[dc59]

Hi Pascal, https://youtu.be/0HKsCVIssqE New 1.3.3.37 got same result.

[dc59]

Hi Pascal, I found file date inside the multi-test-build.zip is all Nov. 12 2023, could it be problem that FW file is not really been updated?

[benlye]

@dc59 I think you saw the same thing as me, an email received last night (17/11) saying 'Please test the version 1.3.3.37 same location which should be available in the next 5 minutes (auto build in progress)' but this looks like Github doing something strange and sending an email for a message Pascal posted a week ago.

There is no new build since November 12th.

[dc59]

Thanks benlye, I did receive the mail as you mentioned,that’s why I downloaded test build again for test and found the file date problem!