WM331 GimbalCalib JointCoarse and GimbalCalib LinearHall

[rsrmdp]

F:\dji-ftm>comm_og_service_tool.py COM7 -vv WM331 GimbalCalib JointCoarse Opened COM7 at 9600

Info: The Gimbal will move through its boundary positions, then it will fine-tune its central position. It will take around 15 seconds.

Prepared binary packet: 55 0e 04 66 0a 04 66 f7 20 04 08 01 6b 1b Sending packet... Waiting for reply... Timeout while waiting for reply. Retrieved 10 packets (527b), dropped 0 fragments (0b) Prepared binary packet: 55 0e 04 66 0a 04 66 f7 20 04 08 01 6b 1b Sending packet... Waiting for reply... Timeout while waiting for reply. Retrieved 1 packets (68b), dropped 0 fragments (0b) Prepared binary packet: 55 0e 04 66 0a 04 66 f7 20 04 08 01 6b 1b Sending packet... Waiting for reply... Timeout while waiting for reply. Retrieved 7 packets (341b), dropped 0 fragments (0b) No response received. Error: No response on calibration command JointCoarse request.

F:\dji-ftm>comm_og_service_tool.py COM7 -vv WM331 GimbalCalib LinearHall Opened COM7 at 9600

Info: The Gimbal will slowly move through all positions in all axes, several times. It will take around 30 seconds.

Prepared binary packet: 55 0e 04 66 0a 04 42 02 20 04 08 02 ce 05 Sending packet... Waiting for reply... Timeout while waiting for reply. Retrieved 2 packets (139b), dropped 0 fragments (0b) Prepared binary packet: 55 0e 04 66 0a 04 42 02 20 04 08 02 ce 05 Sending packet... Waiting for reply... Timeout while waiting for reply. Retrieved 8 packets (396b), dropped 0 fragments (0b) Prepared binary packet: 55 0e 04 66 0a 04 42 02 20 04 08 02 ce 05 Sending packet... Waiting for reply... Timeout while waiting for reply. Retrieved 2 packets (128b), dropped 0 fragments (0b) No response received. Error: No response on calibration command LinearHall request.

I would think that there is some hardware error, but I already repaired a sensor and from the app I did not correct the stabilization.

[linoko]

That happend when do this callibration via python. Is the gimbals leveled? May be you received error message "Gimbal calibration 40011)

[rsrmdp]

That happend when do this callibration via python. Is the gimbals leveled? May be you received error message "Gimbal calibration 40011)

that error does not appear

[linoko]

That happend when do this callibration via python. Is the gimbals leveled? May be you received error message "Gimbal calibration 40011)

that error does not appear

So what is the major issue that you have, describe it please?

[rsrmdp]

That happend when do this callibration via python. Is the gimbals leveled? May be you received error message "Gimbal calibration 40011)

that error does not appear

So what is the major issue that you have, describe it please?

apparently as it reads I am not receiving information from the gimbal. If I find a solution I will post it here

[linoko]

That happend when do this callibration via python. Is the gimbals leveled? May be you received error message "Gimbal calibration 40011)

that error does not appear

So what is the major issue that you have, describe it please?

apparently as it reads I am not receiving information from the gimbal. If I find a solution I will post it here

You will not see incoming info from gimbal, it only seen on DJI Spark

[linoko]

Someone have solution to share?

[vserena82]

Hello,

I have same problem. I have P4P with raplaced gimbal yaw motor, II'm trying to use JointCoarse and LinearHall with WIN10:

C:\DJI>py comm_og_service_tool.py COM4 -vv WM331 GimbalCalib JointCoarse
Opened COM4 at 9600

Info: The Gimbal will move through its boundary positions, then it will fine-tune its central position. It will take around 15 seconds.

Prepared binary packet:
55 0e 04 66 0a 04 d0 f3 20 04 08 01 f3 ec
Sending packet...
Waiting for reply...
Timeout while waiting for reply.
Retrieved 1 packets (68b), dropped 0 fragments (0b)
Prepared binary packet:
55 0e 04 66 0a 04 d0 f3 20 04 08 01 f3 ec
Sending packet...
Waiting for reply...
Timeout while waiting for reply.
Retrieved 8 packets (401b), dropped 0 fragments (0b)
Prepared binary packet:
55 0e 04 66 0a 04 d0 f3 20 04 08 01 f3 ec
Sending packet...
Waiting for reply...
Timeout while waiting for reply.
Retrieved 1 packets (68b), dropped 0 fragments (0b)
No response received.
Error: No response on calibration command JointCoarse request.

There is a solution? Thank you

[rsrmdp]

there is no solution at the moment.

[rsrmdp]

Only 1 https://youtu.be/4q9fmd5iWVM 2 https://youtu.be/0G7p9EroalM I hope... it works for you. but they changed the bell. maybe changing the Hall sensors will fix it.