not support DSCope U2P20?

[amigomcu]

hi all, it not support DSCope U2P20? (revise the scopehal-apps and libsigrok4DSL * for U2P20(IdentifyHardware and dsl_dev_open) not show any waveform in ngscopeclient

steven@steven-VirtualBox:~/scopehal-sigrok-bridge/build$ ./scopehal-sigrok-bridge DSCope libsigrok4DSL ver: '0.2.0' Selected driver DSCope, scanning... Found device: DreamSourceLab - DSCope U2P20 -> USB bus 2 : dev 6 Sample bits: 8 (scope) Device has 2 channels

available operation mode: Normal available operation mode: Internal Test Initial op mode: Normal; stream = 0 vdiv options: 10 (0.1V), 20 (0.2V), 50 (0.5V), 100 (1.0V), 200 (2.0V), 500 (5.0V), 1000 (10.0V), 2000 (20.0V), Hardware ADC report range: 0a - f5 (adj: 1.085) (Clipping detection supported) Client connected to SCPI socket Client connected to data plane socket Updated coupling for ch0, now AC1M Updated RANGE; Wanted 50.000000 (0.500000 PtP), result: 94120718662528 Updated coupling for ch1, now AC1M Updated RANGE; Wanted 50.000000 (0.500000 PtP), result: 94120718662528 Updated RATE; now 1000000 Updated DEPTH; now 10000 Updated ENABLED for ch0, now 1 Set trigger DELAY to 0 (%0) Set trigger SOU to 0 Set trigger LEV to 0.000000 Set trigger EDGE to RISING Set trigger DELAY to 0 (%0) /home/steven/scopehal-apps/lib/scopehal/DSLabsOscilloscope.cpp void DSLabsOscilloscope::IdentifyHardware() { //Assume no MSO channels to start m_analogChannelCount = 0; m_digitalChannelBase = 0; m_digitalChannelCount = 0;

m_series = SERIES_UNKNOWN;

if (m_model == "DSCope U3P100") { m_series = DSCOPE_U3P100; LogDebug("Found DSCope U3P100\n");

m_analogChannelCount = 2; m_digitalChannelCount = 0;

} else if (m_model == "DSLogic U3Pro16") { m_series = DSLOGIC_U3PRO16; LogDebug("Found DSLogic U3Pro16\n");

m_analogChannelCount = 0; m_digitalChannelCount = 16;

} // ********add U2P20// else if (m_model == "DSCope U2P20") { m_series = DSCOPE_U3P100; LogDebug("Found DSCope U2P20\n");

m_analogChannelCount = 2; m_digitalChannelCount = 0; }

if (m_series == SERIES_UNKNOWN) LogWarning("Unknown DSLabs model "%s"\n", m_model.c_str()); }

/home/steven/DSView/libsigrok4DSL/hardware/DSL/dsl.c

SR_PRIV int dsl_dev_open(struct sr_dev_driver *di, struct sr_dev_inst *sdi, gboolean fpga_done) ret = dsl_wr_reg(sdi, CTR0_ADDR, bmNONE); // dessert clear / Check HDL version */ ret = dsl_hdl_version(sdi, &hw_info); sr_info("HDL ver is %x",hw_info); // ********add U2P20// //if ((ret != SR_OK) || (hw_info != DSL_HDL_VERSION)) { if ((ret != SR_OK) ) { sr_err("%s: HDL verison incompatible!", func); sdi->status = SR_ST_INCOMPATIBLE; return SR_ERR; }