nrc7292_sw_pkg
nrc7292_sw_pkg copied to clipboard
Published
20 hours ago •
newracom
newracom
STA waiting for IP
I have two Raspberry Pi 4 Model B (STA and AP) with Raspbian OS (32 bit) installed, connected to the Wi-Fi HaLow AHPI7292SA boards. I followed the guide and, after replacing the file nrc7292_bd.dat with the one from issue #60 (to solve the target mismatch error), I ran the start.py script on AP:
pi@raspberrypi:~ $ ~/nrc_pkg/script/start.py 1 0 EU
Done.
Done.
------------------------------
Model : 7292
STA Type : AP
Country : EU
Security Mode : OPEN
BD Name : nrc7292_bd.dat
AMPDU : AUTO
Download FW : uni_s1g.bin
MAX TX Power : 24 dBm
BSS MAX IDLE : 1800
Rate Control : Consistent RC
Default MCS : 2
------------------------------
NRC AP setting for HaLow...
[*] Set Max CPU Clock on RPi
1500000
1500000
1500000
1500000
Done
[0] Clear
Selected interface 'wlan0'
[1] Copy and Set Module Parameters
total 688
drwxr-xr-x 2 pi pi 4096 Jan 28 17:30 .
drwxr-xr-x 4 pi pi 4096 Jan 28 17:27 ..
-rwxrwxrwx 1 pi pi 271 Jan 28 17:27 copy
-rwxr-xr-x 1 pi pi 2128 Jan 28 17:32 nrc7292_bd.dat
-rwxr-xr-x 1 pi pi 342080 Jan 28 17:27 nrc7292_cspi.bin
-rwxr-xr-x 1 root root 342080 Feb 5 12:29 uni_s1g.bin
-rwxr-xr-x 1 root root 342080 Feb 5 12:29 /lib/firmware/uni_s1g.bin
====================================
AP INTERFACE : wlan0
AP STATIC IP : 192.168.200.1
NET MASK NUM : 24
====================================
Config for AP is done!
IP and DHCP config done
[2] Set Initial Country
[3] Loading module
sudo insmod /home/pi/nrc_pkg/sw/driver/nrc.ko fw_name=uni_s1g.bin bss_max_idle=1800 ndp_preq=1 listen_interval=1000 bd_name=nrc7292_bd.dat ap_rc_mode=2 sta_rc_mode=2 ap_rc_default_mcs=2 sta_rc_default_mcs=2
[4] Set Maximum TX Power
Type : limit Tx power : 24
OK
[*] Transmission Power Control(TPC) is activated
[5] Set guard interval: auto
[*] Start DHCPCD and DNSMASQ
[*] Self configuration off
[6] Start hostapd on wlan0
[*] configure file copied from: /home/pi/nrc_pkg/script/conf/EU/ap_halow_open.conf
[7] Start NAT
[8] ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.42.0.133 netmask 255.255.255.0 broadcast 10.42.0.255
inet6 fe80::bd54:21ed:dab2:9ca6 prefixlen 64 scopeid 0x20<link>
ether d8:3a:dd:66:b5:ab txqueuelen 1000 (Ethernet)
RX packets 13408 bytes 1000776 (977.3 KiB)
RX errors 0 dropped 3283 overruns 0 frame 0
TX packets 9524 bytes 1445931 (1.3 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 230 bytes 21896 (21.3 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 230 bytes 21896 (21.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
ether 00:c0:ca:b4:0c:f8 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
HaLow AP ready
--------------------------------------------------------------------
Done.
I ran the start.py script on station:
pi@raspberrypi:~ $ ~/nrc_pkg/script/start.py 0 0 EU
Done.
Done.
------------------------------
Model : 7292
STA Type : STA
Country : EU
Security Mode : OPEN
BD Name : nrc7292_bd.dat
AMPDU : AUTO
CQM : ON
Download FW : uni_s1g.bin
MAX TX Power : 24 dBm
BSS MAX IDLE : 1800
Power Save Type : Always On
Listen Interval : 1000
Rate Control : Consistent RC
Default MCS : 2
------------------------------
NRC STA setting for HaLow...
[*] Set Max CPU Clock on RPi
1500000
1500000
1500000
1500000
Done
[0] Clear
[1] Copy and Set Module Parameters
total 688
drwxr-xr-x 2 pi pi 4096 Jan 28 18:25 .
drwxr-xr-x 4 pi pi 4096 Jan 28 18:21 ..
-rwxrwxrwx 1 pi pi 271 Jan 28 18:21 copy
-rwxr-xr-x 1 pi pi 2128 Jan 28 18:25 nrc7292_bd.dat
-rwxr-xr-x 1 pi pi 342080 Jan 28 18:21 nrc7292_cspi.bin
-rwxr-xr-x 1 root root 342080 Feb 5 12:35 uni_s1g.bin
-rwxr-xr-x 1 root root 342080 Feb 5 12:35 /lib/firmware/uni_s1g.bin
====================================
STA INTERFACE : wlan0
STA STATIC IP : 192.168.200.11
NET MASK NUM : 24
Default GW : 192.168.200.1
====================================
Config for STA is done!
IP and DHCP config done
[2] Set Initial Country
[3] Loading module
sudo insmod /home/pi/nrc_pkg/sw/driver/nrc.ko fw_name=uni_s1g.bin bss_max_idle=1800 listen_interval=1000 bd_name=nrc7292_bd.dat ap_rc_mode=2 sta_rc_mode=2 ap_rc_default_mcs=2 sta_rc_default_mcs=2
[4] Set Maximum TX Power
Type : limit Tx power : 24
OK
[*] Transmission Power Control(TPC) is activated
[5] Set guard interval: auto
[*] Start DHCPCD and DNSMASQ
[6] Start wpa_supplicant on wlan0
Successfully initialized wpa_supplicant
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
nl80211: kernel reports: Match already configured
wlan0: CTRL-EVENT-REGDOM-CHANGE init=USER type=COUNTRY alpha2=IT
wlan0: SME: Trying to authenticate with 00:c0:ca:b4:0c:f8 (SSID='halow_demo' freq=5180 MHz)
wlan0: Trying to associate with 00:c0:ca:b4:0c:f8 (SSID='halow_demo' freq=5180 MHz)
wlan0: Associated with 00:c0:ca:b4:0c:f8
wlan0: CTRL-EVENT-CONNECTED - Connection to 00:c0:ca:b4:0c:f8 completed [id=0 id_str=]
wlan0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
[7] Connect and DHCP
Waiting for IP
Waiting for IP
Waiting for IP
Waiting for IP
But the station is stuck on "Waiting for IP" message. The only thing I noticed is that the AP has no IP address on wlan0 interface, so I assume the hostapd is not working somehow.
Debug messages of hostapd:
random: getrandom() support available
Configuration file: /home/pi/nrc_pkg/script/conf/temp_hostapd_config.conf
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:10
nl80211: Supported cipher 00-0f-ac:8
nl80211: Supported cipher 00-0f-ac:9
nl80211: Supported cipher 00-0f-ac:11
nl80211: Supported cipher 00-0f-ac:12
nl80211: Supported cipher 00-0f-ac:6
nl80211: Supports Probe Response offload in AP mode
nl80211: Using driver-based off-channel TX
nl80211: Driver-advertised extended capabilities (default) - hexdump(len=8): 00 00 00 00 00 00 00 40
nl80211: Driver-advertised extended capabilities mask (default) - hexdump(len=8): 00 00 00 00 00 00 00 40
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=6
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=0
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=1
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=2
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=3
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=4
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=5
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=222
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=7
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=8
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=9
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=10
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=11
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=12
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=13
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=14
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=15
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=16
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=17
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=18
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=19
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=20
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=21
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=22
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=23
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=24
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=25
nl80211: Supported vendor command: vendor_id=0xfcffaa subcmd=26
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=0
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=1
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=2
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=3
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=4
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=5
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=6
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=7
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=8
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=9
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=10
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=11
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=12
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=13
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=14
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=15
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=16
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=17
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=18
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=19
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=20
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=21
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=22
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=23
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=24
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=25
nl80211: Supported vendor event: vendor_id=0xfcffaa subcmd=26
nl80211: use P2P_DEVICE support
nl80211: key_mgmt=0x1ff0f enc=0x7ef auth=0x7 flags=0x4000511fbe3d8e0 rrm_flags=0x10 probe_resp_offloads=0x6 max_stations=0 max_remain_on_chan=1000 max_scan_ssids=2
nl80211: interface wlan0 in phy nrc80211
nl80211: Set mode ifindex 4 iftype 3 (AP)
nl80211: Setup AP(wlan0) - device_ap_sme=0 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0xb93fb0
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0xb93fb0 match= multicast=0
nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ) nl_handle=0xb93fb0 match= multicast=0
nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ) nl_handle=0xb93fb0 match= multicast=0
nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC) nl_handle=0xb93fb0 match= multicast=0
nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH) nl_handle=0xb93fb0 match= multicast=0
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ) nl_handle=0xb93fb0 match= multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0xb93fb0 match=04 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0xb93fb0 match=0501 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0xb93fb0 match=0503 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0xb93fb0 match=0504 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0xb93fb0 match=06 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0xb93fb0 match=08 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0xb93fb0 match=09 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0xb93fb0 match=0a multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0xb93fb0 match=11 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0xb93fb0 match=12 multicast=0
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0xb93fb0 match=7f multicast=0
rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0
nl80211: Add own interface ifindex 4 (ifidx_reason -1)
nl80211: if_indices[16]: 4(-1)
nl80211: Do not open EAPOL RX socket - using control port for RX
phy: nrc80211
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
Using existing control interface directory.
ctrl_iface bind(PF_UNIX) failed: Address already in use
ctrl_iface exists, but does not allow connections - assuming it was leftover from forced program termination
Successfully replaced leftover ctrl_iface socket '/var/run/hostapd/wlan0'
wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Previous country code DE, new country code DE
nl80211: Regulatory information - country=DE (DFS-ETSI)
nl80211: 2400-2483 @ 40 MHz 20 mBm
nl80211: 5150-5250 @ 80 MHz 23 mBm (no outdoor)
nl80211: 5250-5350 @ 80 MHz 20 mBm (no outdoor) (DFS)
nl80211: 5470-5725 @ 160 MHz 26 mBm (DFS)
nl80211: 5725-5875 @ 80 MHz 13 mBm
nl80211: 5945-6425 @ 160 MHz 23 mBm (no outdoor)
nl80211: 57000-66000 @ 2160 MHz 40 mBm
nl80211: Added 802.11b mode based on 802.11g information
nl80211: Mode IEEE 802.11g: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472 2484[DISABLED]
nl80211: Mode IEEE 802.11a: 5180 5185 5190 5195 5200 5205 5210 5215 5220 5225 5230 5235 5240 5260[RADAR] 5280[RADAR] 5300[RADAR] 5320[RADAR] 5500[RADAR] 5520[RADAR] 5540[RADAR] 5560[RADAR] 5580[RADAR] 5745 5750 5755 5760 5765
nl80211: Mode IEEE 802.11b: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472 2484[DISABLED]
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=12 freq=2467 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=13 freq=2472 MHz max_tx_power=20 dBm
Allowed channel: mode=2 chan=36 freq=5180 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=37 freq=5185 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=38 freq=5190 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=39 freq=5195 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=40 freq=5200 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=41 freq=5205 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=42 freq=5210 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=43 freq=5215 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=44 freq=5220 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=45 freq=5225 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=46 freq=5230 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=47 freq=5235 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=48 freq=5240 MHz max_tx_power=23 dBm
Allowed channel: mode=2 chan=52 freq=5260 MHz max_tx_power=20 dBm (DFS state = usable)
Allowed channel: mode=2 chan=56 freq=5280 MHz max_tx_power=20 dBm (DFS state = usable)
Allowed channel: mode=2 chan=60 freq=5300 MHz max_tx_power=20 dBm (DFS state = usable)
Allowed channel: mode=2 chan=64 freq=5320 MHz max_tx_power=20 dBm (DFS state = usable)
Allowed channel: mode=2 chan=100 freq=5500 MHz max_tx_power=26 dBm (DFS state = usable)
Allowed channel: mode=2 chan=104 freq=5520 MHz max_tx_power=26 dBm (DFS state = usable)
Allowed channel: mode=2 chan=108 freq=5540 MHz max_tx_power=26 dBm (DFS state = usable)
Allowed channel: mode=2 chan=112 freq=5560 MHz max_tx_power=26 dBm (DFS state = usable)
Allowed channel: mode=2 chan=116 freq=5580 MHz max_tx_power=26 dBm (DFS state = usable)
Allowed channel: mode=2 chan=149 freq=5745 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=150 freq=5750 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=151 freq=5755 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=152 freq=5760 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=153 freq=5765 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=154 freq=5770 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=155 freq=5775 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=156 freq=5780 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=157 freq=5785 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=158 freq=5790 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=159 freq=5795 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=160 freq=5800 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=161 freq=5805 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=162 freq=5810 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=163 freq=5815 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=164 freq=5820 MHz max_tx_power=13 dBm
Allowed channel: mode=2 chan=165 freq=5825 MHz max_tx_power=13 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=12 freq=2467 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=13 freq=2472 MHz max_tx_power=20 dBm
DFS support is enabled
Completing interface initialization
Mode: IEEE 802.11a Channel: 36 Frequency: 5180 MHz
DFS 0 channels required radar detection
nl80211: Set freq 5180 (ht_enabled=1, vht_enabled=0, he_enabled=0, bandwidth=20 MHz, cf1=5180 MHz, cf2=0 MHz)
* freq=5180
* he_enabled=0
* vht_enabled=0
* ht_enabled=1
* sec_channel_offset=0
* channel_type=1
RATE[0] rate=60 flags=0x1
RATE[1] rate=90 flags=0x0
RATE[2] rate=120 flags=0x1
RATE[3] rate=180 flags=0x0
RATE[4] rate=240 flags=0x1
RATE[5] rate=360 flags=0x0
RATE[6] rate=480 flags=0x0
RATE[7] rate=540 flags=0x0
hostapd_setup_bss(hapd=0xb8fd80 (wlan0), first=1)
nl80211: flush -> DEL_STATION wlan0 (all)
Using interface wlan0 with hwaddr 00:c0:ca:b4:0c:f8 and ssid "halow_demo"
nl80211: Set beacon (beacon_set=0)
nl80211: Beacon head - hexdump(len=61): 80 00 00 00 ff ff ff ff ff ff 00 c0 ca b4 0c f8 00 c0 ca b4 0c f8 00 00 00 00 00 00 00 00 00 00 64 00 01 00 00 0a 68 61 6c 6f 77 5f 64 65 6d 6f 01 08 8c 12 98 24 b0 48 60 6c 03 01 24
nl80211: Beacon tail - hexdump(len=194): 07 64 44 45 20 24 01 17 25 01 17 26 01 17 27 01 17 28 01 17 29 01 17 2a 01 17 2b 01 17 2c 01 17 2d 01 17 2e 01 17 2f 01 17 30 01 17 34 04 14 64 05 1a 95 01 0d 96 01 0d 97 01 0d 98 01 0d 99 01 0d 9a 01 0d 9b 01 0d 9c 01 0d 9d 01 0d 9e 01 0d 9f 01 0d a0 01 0d a1 01 0d a2 01 0d a3 01 0d a4 01 0d a5 01 0d 00 3b 02 73 00 2d 1a 0c 00 19 ff 00 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 3d 16 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 7f 08 04 00 00 02 00 00 00 40 dd 18 00 50 f2 02 01 01 01 00 03 a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00
nl80211: ifindex=4
nl80211: beacon_int=100
nl80211: beacon_rate=0
nl80211: rate_type=0
nl80211: dtim_period=2
nl80211: ssid=halow_demo
* beacon_int=100
* dtim_period=2
nl80211: proberesp (offload) - hexdump(len=255): 50 00 00 00 00 00 00 00 00 00 00 c0 ca b4 0c f8 00 c0 ca b4 0c f8 00 00 00 00 00 00 00 00 00 00 64 00 01 00 00 0a 68 61 6c 6f 77 5f 64 65 6d 6f 01 08 8c 12 98 24 b0 48 60 6c 03 01 24 07 64 44 45 20 24 01 17 25 01 17 26 01 17 27 01 17 28 01 17 29 01 17 2a 01 17 2b 01 17 2c 01 17 2d 01 17 2e 01 17 2f 01 17 30 01 17 34 04 14 64 05 1a 95 01 0d 96 01 0d 97 01 0d 98 01 0d 99 01 0d 9a 01 0d 9b 01 0d 9c 01 0d 9d 01 0d 9e 01 0d 9f 01 0d a0 01 0d a1 01 0d a2 01 0d a3 01 0d a4 01 0d a5 01 0d 00 3b 02 73 00 2d 1a 0c 00 19 ff 00 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 3d 16 24 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 7f 08 04 00 00 02 00 00 00 40 dd 18 00 50 f2 02 01 01 01 00 03 a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00
nl80211: hidden SSID not in use
nl80211: privacy=0
nl80211: auth_algs=0x3
nl80211: wpa_version=0x0
nl80211: key_mgmt_suites=0x4
nl80211: pairwise_ciphers=0x0
nl80211: group_cipher=0x1
nl80211: beacon_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: proberesp_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: assocresp_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: ap_max_inactivity=-1
nl80211: multicast to unicast disabled on interface wlan0
wlan0: Deauthenticate all stations at BSS start
nl80211: send_mlme - da=ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0 wait_time=0 no_encrypt=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme - Use bss->freq=5180
nl80211: send_mlme -> send_frame_cmd
nl80211: CMD_FRAME freq=5180 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff 00 c0 ca b4 0c f8 00 c0 ca b4 0c f8 00 00 02 00
nl80211: Frame TX command accepted; cookie 0x1
nl80211: Set wlan0 operstate 0->1 (UP)
netlink: Operstate: ifindex=4 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
nl80211: TX queue param set: queue=0 aifs=1 cw_min=3 cw_max=7 burst_time=15 --> res=0
nl80211: TX queue param set: queue=1 aifs=1 cw_min=7 cw_max=15 burst_time=30 --> res=0
nl80211: TX queue param set: queue=2 aifs=3 cw_min=15 cw_max=63 burst_time=0 --> res=0
nl80211: TX queue param set: queue=3 aifs=7 cw_min=15 cw_max=1023 burst_time=0 --> res=0
wlan0: interface state COUNTRY_UPDATE->ENABLED
wlan0: AP-ENABLED
wlan0: Setup of interface done.
ctrl_iface not configured!
RTM_NEWLINK: ifi_index=4 ifname=wlan0 operstate=5 linkmode=1 ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
nl80211: Set IF_OPER_UP again based on ifi_flags and expected operstate
netlink: Operstate: ifindex=4 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
RTM_NEWLINK: ifi_index=4 ifname=wlan0 operstate=6 linkmode=1 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: RTM_NEWLINK: ifi_index=4 ifname=wlan0 ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
VLAN: vlan_newlink(wlan0)
nl80211: Event message available
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for wlan0
nl80211: MLME event 60 (NL80211_CMD_FRAME_TX_STATUS) on wlan0(00:c0:ca:b4:0c:f8) A1=ff:ff:ff:ff:ff:ff A2=00:c0:ca:b4:0c:f8
nl80211: MLME event frame - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff 00 c0 ca b4 0c f8 00 c0 ca b4 0c f8 00 00 02 00
nl80211: Frame TX status event A1=ff:ff:ff:ff:ff:ff stype=12 cookie=0x1 ack=0
wlan0: Event TX_STATUS (16) received
mgmt::deauth cb
VLAN: RTM_NEWLINK: ifi_index=4 ifname=wlan0 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(wlan0)
Output of uname -a:
Linux raspberrypi 6.1.0-rpi7-rpi-v7l #1 SMP Raspbian 1:6.1.63-1+rpt1 (2023-11-24) armv7l GNU/Linux
