ArduinoMicro does'nt work

[takachinss1001jp]

Dear Sir, Will you Please tell me,What Happed on Arduino Micro? My The following circumstances are folloing; I tried to Assemble ScratchMonky HVPP and TPI Writer with Arduino Micro according User Manual Target Connection Diagram. However It does'nt work.

So Analized what happed on sketch, The Portmapping seemed to wrong. Because folllowing code seemed to unopen the Port. typedef SMoHWIF_Port_Dual<SMoHWIF_PORT_D, 0x0C, 0, // Only Open CTRL2 & 3 SMoHWIF_PORT_F, 0xF1, 0> // CTRL0, CTRL4,CTRL5,CTRL6 & CTRL7 Therefore I think CTRL1,DATA0,DATA1,DATA2,DATA4 are Disabled, And Seemed Undefined DATA5 on PORTE DATA3 on PORTC is not Defined.

I'm look forward your Kindness Cooperation.

Kazuhiro Haitaka.

[microtherion]

Thanks for your question! I'm afraid I'm very rusty on this code, so please give me a few days to think about it and remind me if you haven't heard from me by monday.

[takachinss1001jp]

Thank you your Promt reply. I'm sorry to have taken the trouble in a busy place. I know ScratchMonky software is nice to work for HVPP,ISP,TPI with Arduino Uno which I made with Breadboard. and Thank your release code and Usermanual on git, I Used conveniently to rescue for blicked AVR. If It's possoble, please remind which D0-13 are assined PORTB, PORTC ,PORTD and PORTE and A0-5 are assined to Arduino Leonard(ATmega32U4) are assined to PORTF(Boundary assignment and no A6&A7 like as Arduino Uno).　Portmapping is quite complicated so that I will inform the web as follows; It's written in Japanese, you may see the table for processor which how assined I/O registor mapping. Please see https://ht-deko.com/arduino/portregisters.html. Anyhow I 'm looking forward to remember and check.

Kazuhiro Haitaka

[microtherion]

So I refreshed my memory; here's what's going on:

1. The bitmasks are not literally copied to the data direction registers. Only the 1 bits are used. Any pin corresponding to a 0 bit is left in the direction it was before.

2. The control signals are split across two different ports. CTRL0,4-7 on PORTF and CTRL2,3 on PORTD. CTRL1 is not actually used.

CTRL  01234567
PORTD   23
PORTF 0   4567

Note that the names of these pins on the board are very confusing. PF7 is A0 etc. So here's a table for clarity:

Ctrl	Port	Pin
CTRL0	PF0	A5
CTRL2	PD2	RX
CTRL3	PD3	TX
CTRL4	PF4	A3
CTRL5	PF5	A2
CTRL6	PF6	A1
CTRL7	PF7	A0

Hope that helps!

[takachinss1001jp]

Thank you very much your Commentary concerning CTRL bit. I have clear understood now. By the way I knew CTRL1 is not used as in SMoHWIF_Leonard.h 117 typedef SMoHWIF_Port_Dual<SMoHWIF_PORT_D, 0x0C, 0, 118 SMoHWIF_PORT_F, 0xF1, 0> SMoHWIF_HVPP_Control;

If so, SMoHWIF_Port_Slow in SMoIF_Port.h might be Cause of malfunction. 81 template <uint8_t pin> class SMoHWIF_Port_Slow

I'm going to find out it. It may takes some time. Anyway I will report again, regardless of success or failure. Thank you anyway. I wish you a happy Christmas Kazuhiro Haitaka

[takachinss1001jp]

Thank you and I'm very sorry to keep you waiting. Unfortunetely Not only HVPP but also HVSP TPI ISP with Arduino Micro. Strange thing are nothing happened Arduino Micro D10(RESET/HVRESET) and D11(VCC) with my 100MHz Oscilloscorpe. Despite Each Arduino Micro Pin works as code of LED blink Sketch on Arduino IDE. First of all, I suspected to something wrong VCC control circuit, However attached as Photo Arduino Nano works almost fine Except Long duration of response. As you know This kind of assemble is Unreliable and Possibly poor contact. So frankly Speaking, I'm not prefer this Sir;