openMMC

Open Source modular IPM Controller firmware

Documentation: https://lnls-dig.github.io/openMMC

Installation:

The following packages are needed in your system in order to compile the firmware:

• gcc-arm-none-eabi
• cmake
• cmake-gui (Optional)

gcc-arm-none-eabi can be installed from the pre-compiled files found at: https://launchpad.net/gcc-arm-embedded/+download or you can run the following command under Ubuntu:

sudo apt-get install gcc-arm-none-eabi

Next step is to clone this repository into your workspace.

git clone https://github.com/lnls-dig/openMMC

Compilation

Create a new folder wherever is suitable

cd <build_folder>

Run CMake using the path to the repository folder as an direct argument and the flag -DBOARD=<board_name> and -DVERSION=<board_version> to configure the compilation scripts to your specific board hardware

cmake <path_to_source> -DBOARD=<board_name> -DVERSION=<board_version>

Example:

cmake ~/openmmc/ -DBOARD=afc -DVERSION=3.1

After creating the build files with CMake, you can compile the firmware using make, optionally setting the VERBOSE flag to 1 if you wish to see all the compilation commands

make [VERBOSE=1]

Both a .elf file and a .bin file will be generated in the out folder. You can use any one you prefer to program your processor.

To clean the compilation files (binaries, objects and dependence files), just run

make clean

To make a debug build (to include symbols into elf file, turn off optimizations, etc.) add -DCMAKE_BUILD_TYPE=Debug option to cmake command. Example:

cmake ~/openmmc/ -DBOARD=afc -DVERSION=3.1 -DCMAKE_BUILD_TYPE=Debug

Programming

OpenOCD

Flashing the MMC microcontroller via SWD/JTAG is supported for CMSIS-DAP and Jlink compatible probes through OpenOCD. You can specify the debug probe with the flag -DDEBUG_PROBE=<probe_name>, valid options are cmsis-dap (default) and jlink.

cmake ~/openmmc/ -DBOARD=afc -DVERSION=3.1 -DDEBUG_PROBE=cmsis-dap

This will create a openocd.cfg file in <build_dir>/out.

To flash the application firmware only, run

make program_app

To flash the bootloader firmware only, run

make program_boot

If you want to erase the whole Flash and flash both firmwares:

make program_all

LPC-Link1

It is possible to flash the MMC microcontroller with the LPC-Link1 adapter by using the probe/lpclink1-flash.sh script. You will need to have MCUXpresso IDE installed in your computer. This script assumes that the MCUXpresso binaries are located in /usr/local/mcuxpressoide/ide/binaries/ by default, you can change this path by setting the MCUXPRESSOIDE_BIN environment variable.

./probe/lpclink1-flash.sh firmware.bin LPC1764 0x0000

HPM-Downloader

:warning: Disclaimer: Due to f06f69f, this alternative is deprecated and ipmitool should be used instead, except when updating the OpenMMC application from older versions.

Another option to program the MMC microcontroler is through HPM-Downloader. First, download and compile the HPM. In it's root directory, in order to load the firmware, run

./bin/hpm-downloader --no-retries --ip <MCH_IP_address> --slot <slots_to_be_updated> --component 1 <path_to_openMMC.bin>

Due to timeout on sending packets, it may fails sometimes, with the Completion Code 0xc3 in the ACTIVATE_FIRMWARE_UPLOAD process. If it occurs, just try the same command again, until you receive the Upgrade success message. Now, you have to upload the bootloader, since the old bootloader is incompatible. To succeed this, run

 ./bin/hpm-downloader --ignore-component-check --ip <MCH_IP_address> --slot <slots_to_be_updated> --component 0 <path_to_newboot.bin>

It's also important to mention that you can use the --help command in case of doubt about how to use the HPM commands. Run

./bin/hpm-downloader --help

ipmitool

After 5631857, it's possible to program the firmware and the bootloader through ipmitool, for previous releases, you still need to use hpm-downloader. In order to use it, you have to install the ipmitool, and then generate .hpm files from OpenMMC.bin and newboot.bin. To generate .hpm files, you will need to use bin2hpm. If you have bin2hpm in your $PATH, the .hpm files will be automatically generated for you, provided you build from 0095b14 or more recent versions. After generate the files, you can use the following commands to program the MMC microcontroller. To upgrade the firmware, use

ipmitool -I lan -H host_name_mch -A none -T 0x82 -m 0x20 -t (112 + num_slot*2 in hexadecimal) hpm upgrade openMMC.hpm activate

To upgrade the bootloader, use

ipmitool -I lan -H host_name_mch -A none -T 0x82 -m 0x20 -t (112 + num_slot*2 in hexadecimal) hpm upgrade newboot.hpm activate

Debugging

It is possible to debug the MMC firmware using OpenOCD and GDB. First, connect OpenOCD with the debug probe using the out/openocd.cfg file generated by cmake in the build directory:

openocd -f out/openocd.cfg

Then open GDB:

$ arm-none-eabi-gdb out/openMMC.elf
(gdb) target remote localhost:3333

Now you can use the typical GDB commands to inspect the program flow and variables. Some useful commands when interacting with a microcontroller trough OpenOCD are listed below:

(gdb) monitor reset halt # Resets the microcontroller and immediately halts
(gdb) monitor reset run  # Resets the microcontroller and starts executing
(gdb) load               # Reload the firmware into flash