Failed config on sniffer.common.yaml during setup

[hexonMD]

INFO ESPHome 2024.2.1 INFO Reading configuration /config/esphome/ttgo.yaml... WARNING GPIO0 is a strapping PIN and should only be used for I/O with care. Attaching external pullup/down resistors to strapping pins can cause unexpected failures. See https://esphome.io/guides/faq.html#why-am-i-getting-a-warning-about-strapping-pins WARNING GPIO5 is a strapping PIN and should only be used for I/O with care. Attaching external pullup/down resistors to strapping pins can cause unexpected failures. See https://esphome.io/guides/faq.html#why-am-i-getting-a-warning-about-strapping-pins Failed config

display.st7789v: [source /config/esphome/sniffer_common.yaml:107] platform: st7789v model: TTGO_TDISPLAY_135X240 backlight_pin: number: 4 allow_other_uses: True mode: output: True input: False open_drain: False pullup: False pulldown: False inverted: False ignore_strapping_warning: False drive_strength: 20.0 cs_pin: number: 5 mode: output: True input: False open_drain: False pullup: False pulldown: False inverted: False ignore_strapping_warning: False drive_strength: 20.0 dc_pin: number: 16 mode: output: True input: False open_drain: False pullup: False pulldown: False inverted: False ignore_strapping_warning: False drive_strength: 20.0 reset_pin: number: 23 mode: output: True input: False open_drain: False pullup: False pulldown: False inverted: False ignore_strapping_warning: False drive_strength: 20.0 update_interval: 1s rotation: 270

Couldn't find ID 'temp2'. Please check you have defined an ID with that name in your configuration. These IDs look similar: "temp". lambda: !lambda |- it.rectangle(0, 0, it.get_width(), it.get_height(), id(my_blue)); it.rectangle(0, 19, it.get_width(), it.get_height(), id(my_blue)); // header bar

it.strftime(4,  3, id(sz_13), id(my_yellow), TextAlign::TOP_LEFT, "%Y-%m-%d %H:%M:%S", id(esptime).now());

if (id(system_status).state) {
  it.print(236, 3, id(sz_13), id(my_green), TextAlign::TOP_RIGHT, "Sniffer0 Online");
} else {
  it.print(236, 3, id(sz_13), id(my_red), TextAlign::TOP_RIGHT, "Sniffer0 Offline");
}

int r = 18;

it.print(4,    r, id(sz_24), id(my_gray),   TextAlign::TOP_LEFT,  "PM2.5:");

auto color = id(my_red);
if (id(pm_2_5_aqi).state < 50) color = id(my_green);
else if (id(pm_2_5_aqi).state < 100) color = id(my_yellow);
it.printf(236, r, id(sz_24), color, TextAlign::TOP_RIGHT, "%0.0f AQI", id(pm_2_5_aqi).state);

r += 21;
it.print(4,    r, id(sz_20), id(my_gray),   TextAlign::TOP_LEFT,  "PM:");
it.printf(236, r, id(sz_20), id(my_yellow), TextAlign::TOP_RIGHT, "%0.0f/%0.0f/%0.0f µg/m³", id(pm_1_0).state, id(pm_2_5).state, id(pm_10).state);

r += 25;
it.print(120,    r, id(sz_24), id(my_gray),   TextAlign::TOP_CENTER,  "Environment");

r += 23;
float temp_f = id(temp).state * (9.0/5.0) + 32.0;
float temp2_f = id(temp2).state * (9.0/5.0) + 32.0;
/*it.printf(4,   r, id(sz_20), id(my_yellow), TextAlign::TOP_LEFT, "%0.1f°F", id(temp).state); */
it.printf(4,   r, id(sz_20), id(my_yellow), TextAlign::TOP_LEFT, "%0.1f°F", temp_f);
it.printf(125, r, id(sz_24), id(my_yellow), TextAlign::TOP_CENTER, "%0.1f°F", temp2_f);
it.printf(236, r, id(sz_20), id(my_yellow), TextAlign::TOP_RIGHT,  "%0.1f%%", id(humidity).state);

r += 21;
it.printf(4,   r, id(sz_20), id(my_yellow), TextAlign::TOP_LEFT,  "%0.1f hPa", id(pressure).state);
it.printf(236, r, id(sz_20), id(my_yellow), TextAlign::TOP_RIGHT, "%0.1f kΩ",  id(gas_resistance).state/1000.0);

auto_clear_enabled: True eightbitcolor: False height: 240 width: 135 offset_height: 52 offset_width: 40

[Ralphy140]

You will need to remove the refrence to temp2 if you are not using the ds18b temp sensor package

start at line 147

      # float temp2_f = id(temp2).state * (9.0/5.0) + 32.0;
      /*it.printf(4,   r, id(sz_20), id(my_yellow), TextAlign::TOP_LEFT, "%0.1f°F", id(temp).state); */
      it.printf(4,   r, id(sz_20), id(my_yellow), TextAlign::TOP_LEFT, "%0.1f°F", temp_f);
      # it.printf(125, r, id(sz_24), id(my_yellow), TextAlign::TOP_CENTER, "%0.1f°F", temp2_f);
      it.printf(236, r, id(sz_20), id(my_yellow), TextAlign::TOP_RIGHT,  "%0.1f%%", id(humidity).state);