icm 20948 wake on motion interrupt

[NIIHARIKARAVIPROLU]

Hi, I am facing a problem in icm 20948 with msp430fr5994 by using int .i set a threshold values so that onece when my threshold values is cross i should get int but here it is not happening like that without crossing also i am getting int .I was suspecting that setting of threshold value in register is not proper . the following is my code

//macros used //interrupts const uint8_t REG_ACCEL_INTEL_CTRL =0x12;//userbank2 const uint8_t BIT_ACCEL_INTEL_EN =0x02;//Wake-up On Motion enable bit const uint8_t BIT_ACCEL_INTEL_MODE =0x01;//WOM algorithm selection bit const uint8_t REG_ACCEL_WOM_THR = 0x13; //_BANK_2 // Wake-up On Motion Threshold register const uint8_t BIT_SLEEP =0x40; //bank0 reg 0x06 /< Sleep mode enable bit const uint8_t BIT_SLEEP_CLEAR=0x00;//clear bit sleepin ub0,reg6 const uint8_t REG_PWR_MGMT_1 =0x06;//bank0 /< Power Management 1 register const uint8_t REG_LP_CONFIG = 0x05;// bnk0,reg,5 //Low Power mode config register const uint8_t BIT_ACCEL_CYCLE= 0x20;////bank0,reg,5writhe this value /< Accelerometer cycle mode enable const uint8_t BIT_GYRO_CYCLE = 0x10;//bank0,reg5,write this value /< Gyroscope cycle mode enable const uint8_t REG_GYRO_SMPLRT_DIV =0x00;//bank2,reg0 /< Gyroscope Sample Rate Divider regiser const uint8_t REG_ACCEL_SMPLRT_DIV_1 = 0x10;//bank2,reg 10 /< Acceleration Sensor Sample Rate Divider const uint8_t REG_ACCEL_SMPLRT_DIV_2 = 0x11;//bank2,reg11 /< Acceleration Sensor Sample Rate Divider 2 register */ const uint8_t SHIFT_ACCEL_DLPCFG = 3; /< Accel DLPF Config bit shift */ const uint8_t BIT_PWR_ACCEL_STBY= 0x07; //bank0,reg7 /< Disable accelerometer */ const uint8_t BIT_WOM_INT_EN = 0x08;//bank0,reg10 /< Wake-up On Motion enable bit */ const uint8_t B0_REG10=0x10; const uint8_t EN_GYRO=0x38; const uint8_t REG_INT_STATUS= 0x19;//bnk0 /< Interrupt Status register */ const uint8_t BIT_WOM_INT = 0x08; /< Wake-up on motion interrupt occured bit */ const uint8_t BIT_PLL_RDY = 0x04; /**< PLL ready interrupt occured bit */

int Enable_WOM_Interrupt() { if (changeUserBank(USER_BANK_0,0) < 0)//selecting userbank0 { return -1;
} if (I2C_WRITE(UB0_INT_PIN_CFG, UB0_INT_PIN_CFG_HIGH_50US) < 0) {
return -2; } enable_sleepmode(false);//chacking if//it is sleep mode or not enable_cyclemode(false);//operating in duty cycle mode enable_sensor(true,false);//enablling accelemeter set_sample_rate(1100.0); enable_irq(true);//ensbling wom int if (configAccel(ACCEL_RANGE_16G, ACCEL_DLPF_BANDWIDTH_1209HZ) < 0)//scale range 16g { return -3; } enable_irq(); __delay_cycles(50);

if (changeUserBank(USER_BANK_2,0) < 0) { return -4; } if (I2C_WRITE(REG_ACCEL_INTEL_CTRL, BIT_ACCEL_INTEL_EN|BIT_ACCEL_INTEL_MODE) < 0)//enablewomlogic,comparingprevious with current sample { return -5; }

if (changeUserBank( USER_BANK_0,0) < 0)

{ return -6; } readSensor(); if (changeUserBank(USER_BANK_2,0) < 0) { return -6; } if (I2C_WRITE(REG_ACCEL_WOM_THR,x_Threshold)<0)//setting_threshold_value { return -7; } enableInterrupt(GPIO_PORT_P4, GPIO_PIN4); } uint32_t enable_irq( ) { if (changeUserBank( USER_BANK_0,0) < 0) { return -1; } else if( I2C_WRITE(B0_REG10,BIT_WOM_INT_EN)<0) { return -2; } return 1; } int enable_sleepmode(bool enable) {

    if (enable)
    {
        if (changeUserBank( USER_BANK_0,0) < 0)
        {
            return -1;
        }

         if( I2C_WRITE(REG_PWR_MGMT_1,BIT_SLEEP)<0)
           {
            return -2;

           }
    }
    else
    {
        if (changeUserBank( USER_BANK_0,0) < 0)
        {
            return -1;
        }
         if( I2C_WRITE(REG_PWR_MGMT_1,BIT_SLEEP_CLEAR)<0)
          {
            return -2;
           }
    }

    return 1;

}

int enable_cyclemode(bool enable) {

if (enable)
{
    if (changeUserBank( USER_BANK_0,0) < 0)
    {
        return -1;
    }
    if(I2C_WRITE(REG_LP_CONFIG,(BIT_ACCEL_CYCLE|BIT_GYRO_CYCLE))<0)
    {
        return -2;
    }
}
else
{

    if (changeUserBank( USER_BANK_0,0) < 0)
    {
        return -1;
    }
    if(I2C_WRITE(REG_LP_CONFIG,(BIT_ACCEL_CYCLE&BIT_GYRO_CYCLE))<0)
           {
               return -2;
           }
}
return 1;

} uint32_t set_sample_rate(float sampleRate) { set_gyro_sample_rate(sampleRate); set_accel_sample_rate(sampleRate);

return 1;

} float set_gyro_sample_rate(float sampleRate) { uint8_t gyroDiv; float gyroSampleRate;

/* Calculate the sample rate divider */
gyroSampleRate = (1125.0 / sampleRate) - 1.0;

/* Check if it fits in the divider register */
if ( gyroSampleRate > 255.0 )
{
    gyroSampleRate = 255.0;
}

if ( gyroSampleRate < 0 )
{
    gyroSampleRate = 0.0;
}

/* Write the value to the register */
gyroDiv = (uint8_t) gyroSampleRate;
if(changeUserBank( USER_BANK_2,0) < 0)
{
    return -1;
}
if(I2C_WRITE(REG_GYRO_SMPLRT_DIV, gyroDiv)<0)
{
    return -2;
}

/* Calculate the actual sample rate from the divider value */
gyroSampleRate = 1125.0 / (gyroDiv + 1);

return gyroSampleRate;

} float set_accel_sample_rate(float sampleRate) { uint16_t accelDiv; float accelSampleRate;

/* Calculate the sample rate divider */
accelSampleRate = (1125.0 / sampleRate) - 1.0;

/* Check if it fits in the divider registers */
if ( accelSampleRate > 4095.0 ) {
    accelSampleRate = 4095.0;
}

if ( accelSampleRate < 0 ) {
    accelSampleRate = 0.0;
}

/* Write the value to the registers */
accelDiv = (uint16_t) accelSampleRate;
I2C_WRITE(REG_ACCEL_SMPLRT_DIV_1, (uint8_t) (accelDiv >> 8) );
I2C_WRITE(REG_ACCEL_SMPLRT_DIV_2, (uint8_t) (accelDiv & 0xFF) );

/* Calculate the actual sample rate from the divider value */
accelSampleRate = 1125.0 / (accelDiv + 1);

return accelSampleRate;

} uint32_t enable_sensor(bool accel, bool gyro) { // uint8_t pwrManagement1; // uint8_t pwrManagement2;

// pwrManagement2 = 0; if ( accel ) { if (changeUserBank(USER_BANK_0,0) < 0 ) { I2C_WRITE(UB0_PWR_MGMNT_2, BIT_PWR_ACCEL_STBY);

     return -1;
 }
}
else if ( gyro )
{
    if (changeUserBank(USER_BANK_0,0) < 0 )
    {
      I2C_WRITE(UB0_PWR_MGMNT_2, EN_GYRO);
        return -2;
    }

}

return 1;

}

this is when i get interuupt in took a pin void int_pin() { GPIO_setAsInputPin(GPIO_PORT_P4,GPIO_PIN4); GPIO_setAsInputPinWithPullUpResistor(GPIO_PORT_P4,GPIO_PIN4); GPIO_selectInterruptEdge(GPIO_PORT_P4, GPIO_PIN4, GPIO_LOW_TO_HIGH_TRANSITION); GPIO_clearInterrupt(GPIO_PORT_P4,GPIO_PIN4);

}

#pragma vector=PORT4_VECTOR __interrupt void Port_4(void) //ISR

{ Tx_Uart0_String("\nharsh_braking");///when my threshold values crosses it should here but if axis value is less than threshold value then also it is in isr and not clearing

GPIO_clearInterrupt(GPIO_PORT_P4, GPIO_PIN4);

} so is there any thing i need to add or change should be done mail me [email protected] as early as possible so i haave codded in such a format that i keep on reading accelerometer axis values but once threshold values crosses reaches ISR Thanks in advance