v1.0.0-beta1 Drawing Package

[jrsteensen]

UIP

• [ ] Mechanical Drawings
  • [ ] OH1A1 - ASSY, UPPER INSTRUMENT PANEL
  • [ ] OH1A2 - ASSY, PANEL, MASTER ARM
  • [ ] OH1A3 - ASSY, DDI
  • [ ] OH1A4 - ASSY, EYEBROW WARNING INDICATOR, LEFT
  • [ ] OH1A5 - ASSY, EYEBROW WARNING INDICATOR, RIGHT
  • [ ] OH1A6 - ASSY, PANEL, SPIN RECOVERY
  • [ ] OH1A8 - ASSY, UPFRONT CONTROL PANEL
    • [ ] OH1A8A1 - ASSY, UPFRONT CONTROL PANEL PRIMARY MODULE
    • [ ] OH1A8A2 - ASSY, PANEL, HUD
    • [ ] OH1A8A3 - ASSY, AP SWITCH MODULE
    • [ ] OH1A8A4 - ASSY, HUD BIT BOX

LIP

• [ ] Mechanical Drawings
  • [ ] OH2A1 - ASSY, LOWER INSTRUMENT PANEL
  • [ ] OH2A1A1 - ASSY, LIP STRUCTURE
  • [ ] OH2A2A1 - ASSY, LEFT LIP MODULE
    • [ ] OH2A2A1A1 - ASSY, PANEL, JETT SLEECT
    • [ ] OH2A2A1A2 - ASSY, PANEL, IFEI
    • [ ] OH2A2A1A3 - ASSY, PANEL, VIDEO RECORD
  • [ ] OH2A3A1 - ASSY, AMPCD MODULE
  • [ ] OH2A4A1 - ASSY, PANEL, RWR CONTROL
  • [ ] OH2A5A1 - ASSY, PANEL, ECM/DISP
  • [ ] OH2A6A1 - ASSY, CABIN PRESSURE GAUGE
  • [ ] OH2A7A1 - ASSY, STANDBY INSTRUMENT MODULE

L CONSOLE

• [ ] Mechanical Drawings
  • [ ] OH4A1 - ASSY, LEFT CONSOLE
  • [ ] OH4A1A1 - ASSY, LEFT CONSOLE STRUCTURE
  • [ ] OH4A2A1 - ASSY, LANDING GEAR PANEL
  • [ ] OH4A3A1 - ASSY, SELECT JETT PANEL
  • [ ] OH4A3A2 - ASSY, PARK BRAKE HANDLE
  • [ ] OH4A3A3 - ASSY, BRAKE PRESS GAUGE
  • [ ] OH4A4A1 - ASSY, FIRE TEST PANEL
  • [ ] OH4A4A2 - ASSY, EXTERNAL LT PANEL
  • [ ] OH4A4A3 - ASSY, GEN TIE PANEL
  • [ ] OH4A5A1 - ASSY, FUEL PANEL
  • [ ] OH4A5A2 - ASSY, APU/ENG CRANK PANEL
  • [ ] OH4A6A1 - ASSY, FCS PANEL
  • [ ] OH4A7A1 - ASSY, COMM PANEL
  • [ ] OH4A7A2 - ASSY, OBOGS PANEL
  • [ ] OH4A7A3 - ASSY, MC/HYD PANEL
  • [ ] OH4A7A4 - ASSY, ANT SEL PANEL
  • [ ] OH4A8A1 - ASSY, LEFT CIRCUIT BREAKERS
  • [ ] OH4A8A2 - ASSY, DISPENSE BUTTON
  • [ ] OH4A8A3 - ASSY, NUC ENABLE SWITCH
  • [ ] OH10A1A1 - ASSY, SIM PWR PANEL

R CONSOLE

• [ ] Mechanical Drawings
  • [ ] OH5A1 - ASSY, RIGHT CONSOLE
  • [ ] OH5A1A1 - ASSY, RIGHT CONSOLE STRUCTURE
  • [ ] OH5A2A1 - ASSY, HOOK LEVER & INDICATOR
  • [ ] OH5A2A2 - ASSY, WING FOLD HANDLE
  • [ ] OH5A2A3 - ASSY, AV COOL SWITCH
  • [ ] OH5A2A4 - ASSY, RADAR ALTIMETER GAUGE
  • [ ] OH5A2A5 - ASSY, HYD PRESS GAUGE
  • [ ] OH5A2A6 - ASSY, BUNO PLACARD
  • [ ] OH5A2A7 - ASSY, LDG CHKLST PANEL
  • [ ] OH5A3A1 - ASSY, CAUTION LIGHT PANEL
  • [ ] OH5A4A1 - ASSY, ELEC PANEL
  • [ ] OH5A5A1 - ASSY, ECS PANEL
  • [ ] OH5A5A2 - ASSY, DEFOG/WINDSHIELD PANEL
  • [ ] OH5A6A1 - ASSY, INTR LT PANEL
  • [ ] OH5A7A1 - ASSY, SNSR PANEL
  • [ ] OH5A8A1 - ASSY, SIM CNTL PANEL
  • [ ] OH5A9A1 - ASSY, KY58 PANEL
  • [ ] OH5A10A1 - ASSY, RIGHT CIRCUIT BREAKERS
  • [ ] OH5A10A2 - ASSY, CANOPY SWITCH
  • [ ] OH5A11A1 - ASSY, BULKHEAD INTERCONNECT PANEL

CENTER TUB

• [ ] Mechanical Drawings
  • [ ] OHXXX - ASSY, CENTER TUB

SEAT v1.5

• [ ] Mechanical Drawings
  • [ ] TBD

THROTTLE

• [ ] Mechanical Drawings
  • [ ] OH4A9A1 - ASSY, THROTTLE QUADRANT
  • [ ] OH4A9A2 - ASSY, OUTBOARD THROTTLE GRIP
  • [ ] OH4A9A3 - ASSY, INBOARD THROTTLE GRIP

STICK

• [ ] Mechanical Drawings
  • [ ] TBD

TOP LEVEL ASSY

• [ ] Mechanical Drawings
  • [ ] OH000-01 - ASSY, OPENHORNET HOME FLIGHT SIMULATOR
  • [ ] #255

[jrsteensen]

Removed interconnect drawings which are being bumped to beta2 milestone.

[russellmm]

Left and Right Console Construction Issue: Correct angles on "aft Internal Bulkhead" required for smooth installation of remainder of ribs 1] Ensure that the angle of the cut on the bottom of the Aft Internal Bulkhead is 22.1 degrees. This will allow it to lie flat on the console floor at the correct angle and allow the installation of the rest of the ribs to go smoothly. 2] Each Rib should be centered on holes in the console floor for perfect alignment.

[russellmm]

Left and Right Console Issue: Correct angle of Canopy rail required for smooth transition/fit with Ribs and Rib Covering Comment: The Angle needs to be 22.5 degrees. Also note, the width of the Canopy rail at its widest point after being cut needs to be ~90mm

[russellmm]

Lower Instrument Panel Construction Issue: Angle at the back of "Upper Instrument Panel Mount" critical to proper installation of "right inboard footwell wall and left inboard footwell wall" Comment: The angle of the cut on the back of the Upper Instrument Panel should be 13 degrees. This will allow the proper overhang of 3.175mm for the Right Inboard footwell wall and 12.78mm for the left Inboard Footwell wall.

[jrsteensen]

Going to track this per-issue in the beta 1 project.