openwrt-redmi-ax3000
openwrt-redmi-ax3000 copied to clipboard
hzyitc
R81 (AX3000 works but not tested at all)
@hzyitc 我补充一下 AX3000 RA81的 兼容性情况： 镜像使用 ipq50xx-qsdk-kernel-5.4-openwrt-21.02-qsdk-11.5.05.841.1029 2023-06-08 10:03:31 UTC(+00:00)
- 正常启动
- 交换机正常
- CPU Ethernet 正常
- NSS NAT无法使用(具体表现为iperf3测速时最好只能跑到620Mbps，且 CPU 满载)
- 2.4G/5G WiFi正常，但 5G 160Mhz需要同 README 相同的设置.
启动过程中dmesg: https://gist.github.com/baysonfox/454873fb47d4276241b92487c231a632 (刷了自定义的扩容分区表，不知有无影响)
NSS NAT无法使用(具体表现为iperf3测速时最好只能跑到620Mbps，且 CPU 满载)
单纯的nat还是PPPoE? 路由上跑的iperf3还是外部设备?如果是外部设备，连的是wifi还是有线。
NSS NAT无法使用(具体表现为iperf3测速时最好只能跑到620Mbps，且 CPU 满载)
单纯的nat还是PPPoE? 路由上跑的iperf3还是外部设备?如果是外部设备，连的是wifi还是有线。
R81可以刷了吗！
NSS NAT无法使用(具体表现为iperf3测速时最好只能跑到620Mbps，且 CPU 满载)
单纯的nat还是PPPoE? 路由上跑的iperf3还是外部设备?如果是外部设备，连的是wifi还是有线。
目前是纯 NAT (PPPoE还未进行测试), 路由上用iperf3作为服务端和客户端都进行了测试, 作为服务端时速度在 825Mbps 左右, 且比较稳定. 但作为客户端时速度会有较大波动(869Mbps - 602Mbps), 对端设备是一台J4125的机器, 使用1Gbps的网卡进行有线连接. (感觉有种类似“暖机”的情况？在部分情况下某次测试最开始的速度可能只有300-400Mbps, 之后速度会回到正常状态.)
作为服务端进行测试:
----------------------------------------------------------- Server listening on 5201 (test #1) ----------------------------------------------------------- Accepted connection from 192.168.1.3, port 55666 [ 5] local 192.168.1.1 port 5201 connected to 192.168.1.3 port 55676 [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 104 MBytes 874 Mbits/sec [ 5] 1.00-2.00 sec 108 MBytes 909 Mbits/sec [ 5] 2.00-3.00 sec 76.8 MBytes 642 Mbits/sec [ 5] 3.00-4.00 sec 78.3 MBytes 658 Mbits/sec [ 5] 4.00-5.00 sec 108 MBytes 905 Mbits/sec [ 5] 5.00-6.00 sec 106 MBytes 891 Mbits/sec [ 5] 6.00-7.00 sec 105 MBytes 881 Mbits/sec [ 5] 7.00-8.00 sec 109 MBytes 912 Mbits/sec [ 5] 8.00-9.00 sec 97.9 MBytes 822 Mbits/sec [ 5] 9.00-10.00 sec 96.7 MBytes 811 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate [ 5] 0.00-10.00 sec 990 MBytes 830 Mbits/sec receiver ----------------------------------------------------------- Server listening on 5201 (test #2) ----------------------------------------------------------- Accepted connection from 192.168.1.3, port 53598 [ 5] local 192.168.1.1 port 5201 connected to 192.168.1.3 port 53608 [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 99.4 MBytes 832 Mbits/sec [ 5] 1.00-2.00 sec 104 MBytes 875 Mbits/sec [ 5] 2.00-3.00 sec 98.6 MBytes 827 Mbits/sec [ 5] 3.00-4.00 sec 97.3 MBytes 816 Mbits/sec [ 5] 4.00-5.00 sec 97.0 MBytes 814 Mbits/sec [ 5] 5.00-6.01 sec 96.9 MBytes 807 Mbits/sec [ 5] 6.01-7.01 sec 85.5 MBytes 719 Mbits/sec [ 5] 7.01-8.00 sec 103 MBytes 870 Mbits/sec [ 5] 8.00-9.00 sec 98.6 MBytes 827 Mbits/sec [ 5] 9.00-10.00 sec 98.3 MBytes 825 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate [ 5] 0.00-10.00 sec 979 MBytes 821 Mbits/sec receiver ----------------------------------------------------------- Server listening on 5201 (test #3) -----------------------------------------------------------
作为客户端进行测试:
Connecting to host 192.168.1.3, port 5201 [ 5] local 192.168.1.1 port 49646 connected to 192.168.1.3 port 5201 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 93.1 MBytes 780 Mbits/sec 0 618 KBytes [ 5] 1.00-2.00 sec 103 MBytes 861 Mbits/sec 0 648 KBytes [ 5] 2.00-3.00 sec 104 MBytes 869 Mbits/sec 0 718 KBytes [ 5] 3.00-4.02 sec 98.2 MBytes 807 Mbits/sec 0 836 KBytes [ 5] 4.02-5.01 sec 74.9 MBytes 639 Mbits/sec 0 836 KBytes [ 5] 5.01-6.03 sec 73.9 MBytes 608 Mbits/sec 0 977 KBytes [ 5] 6.03-7.03 sec 72.0 MBytes 602 Mbits/sec 0 977 KBytes [ 5] 7.03-8.00 sec 74.8 MBytes 645 Mbits/sec 0 977 KBytes [ 5] 8.00-9.00 sec 91.7 MBytes 768 Mbits/sec 0 977 KBytes [ 5] 9.00-10.00 sec 101 MBytes 854 Mbits/sec 0 1.21 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.00 sec 886 MBytes 743 Mbits/sec 0 sender [ 5] 0.00-10.01 sec 886 MBytes 742 Mbits/sec receiver root@OpenWrt:~# iperf3 -c 192.168.1.3 Connecting to host 192.168.1.3, port 5201 [ 5] local 192.168.1.1 port 49660 connected to 192.168.1.3 port 5201 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 77.4 MBytes 647 Mbits/sec 0 660 KBytes [ 5] 1.00-2.00 sec 101 MBytes 848 Mbits/sec 0 693 KBytes [ 5] 2.00-3.00 sec 106 MBytes 886 Mbits/sec 0 738 KBytes [ 5] 3.00-4.01 sec 60.9 MBytes 506 Mbits/sec 0 738 KBytes [ 5] 4.01-5.01 sec 62.5 MBytes 524 Mbits/sec 0 738 KBytes [ 5] 5.01-6.00 sec 86.4 MBytes 733 Mbits/sec 0 827 KBytes [ 5] 6.00-7.00 sec 76.0 MBytes 639 Mbits/sec 0 1.10 MBytes [ 5] 7.00-8.00 sec 96.2 MBytes 807 Mbits/sec 0 1.10 MBytes [ 5] 8.00-9.00 sec 86.1 MBytes 722 Mbits/sec 0 1.15 MBytes [ 5] 9.00-10.00 sec 87.5 MBytes 734 Mbits/sec 0 1.15 MBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.00 sec 840 MBytes 704 Mbits/sec 0 sender [ 5] 0.00-10.01 sec 839 MBytes 703 Mbits/sec receiver iperf Done.
测试时的ps返回:
PID USER VSZ STAT COMMAND
1 root 1392 S /sbin/procd
2 root 0 SW [kthreadd]
3 root 0 IW
hi, do you mind share what you have progress with Xiaomi AX3000. Would love to see how it perform
Maybe someone wants to make a video and upload it to YouTube about how to install openWRT on R81
