esp-hosted
esp-hosted copied to clipboard
Published
20 hours ago •
espressif
espressif
ESP32 Unable to detect Flash Size
I'm using a AT25SF321B as the SPI flash for an ESP32-D0WD-V3 IC. I can successfully detect the flash chip, but the size isn't able to be detected. Is there a way to ignore the flash size during runtime? Before we had manually commented out the do_core_init check in the last firmware version (v0.4). Is there something incompatible with the SPI Flash we are using? It seems to correctly flash the chip using the write_flash command, but booting fails.
Output of flash_id command
Detecting chip type... ESP32
Chip is ESP32-D0WD-V3 (revision v3.0)
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
Crystal is 40MHz
MAC: f0:08:d1:4c:fb:48
Uploading stub...
Running stub...
Stub running...
Manufacturer: 1f
Device: 8701
Detected flash size: Unknown
Hard resetting via RTS pin...
Output once it tries to boot
I (13) boot: ESP-IDF v4.4.1-472-gc9140caf8c-dirty 2nd stage bootloader
I (13) boot: compile time 21:33:21
I (13) boot: chip revision: 3
I (16) boot_comm: chip revision: 3, min. bootloader chip revision: 0
I (23) boot.esp32: SPI Speed : 40MHz
I (28) boot.esp32: SPI Mode : DIO
I (32) boot.esp32: SPI Flash Size : 4MB
I (37) boot: Enabling RNG early entropy source...
I (42) boot: Partition Table:
I (46) boot: ## Label Usage Type ST Offset Length
I (53) boot: 0 nvs WiFi data 01 02 00009000 00004000
I (61) boot: 1 otadata OTA data 01 00 0000d000 00002000
I (68) boot: 2 phy_init RF data 01 01 0000f000 00001000
I (76) boot: 3 factory factory app 00 00 00010000 00100000
I (83) boot: 4 ota_0 OTA app 00 10 00110000 00100000
I (91) boot: 5 ota_1 OTA app 00 11 00210000 00100000
I (98) boot: End of partition table
I (102) boot: Defaulting to factory image
I (107) boot_comm: chip revision: 3, min. application chip revision: 0
I (114) esp_image: segment 0: paddr=00010020 vaddr=3f400020 size=15e00h ( 89600) map
I (155) esp_image: segment 1: paddr=00025e28 vaddr=3ffbdb60 size=0553ch ( 21820) load
I (164) esp_image: segment 2: paddr=0002b36c vaddr=40080000 size=04cach ( 19628) load
I (172) esp_image: segment 3: paddr=00030020 vaddr=400d0020 size=769dch (485852) map
I (348) esp_image: segment 4: paddr=000a6a04 vaddr=40084cac size=181d4h ( 98772) load
I (389) esp_image: segment 5: paddr=000bebe0 vaddr=50000000 size=00010h ( 16) load
I (404) boot: Loaded app from partition at offset 0x10000
I (404) boot: Disabling RNG early entropy source...
I (415) cpu_start: Pro cpu up.
I (416) cpu_start: Starting app cpu, entry point is 0x4008121c
I (410) cpu_start: App cpu up.
I (432) cpu_start: Pro cpu start user code
I (432) cpu_start: cpu freq: 240000000
I (432) cpu_start: Application information:
I (437) cpu_start: Project name: network_adapter
I (442) cpu_start: App version: 293978e
I (447) cpu_start: Compile time: Jul 20 2022 21:33:02
I (453) cpu_start: ELF file SHA256: 573ea08fdc881889...
I (459) cpu_start: ESP-IDF: v4.4.1-472-gc9140caf8c-dirty
I (466) heap_init: Initializing. RAM available for dynamic allocation:
I (473) heap_init: At 3FFAFF10 len 000000F0 (0 KiB): DRAM
I (479) heap_init: At 3FFB6388 len 00001C78 (7 KiB): DRAM
I (485) heap_init: At 3FFB9A20 len 00004108 (16 KiB): DRAM
I (492) heap_init: At 3FFD1498 len 0000EB68 (58 KiB): DRAM
I (498) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM
I (504) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM
I (510) heap_init: At 4009CE80 len 00003180 (12 KiB): IRAM
I (518) spi_flash: detected chip: generic
I (521) spi_flash: flash io: dio
E (525) spi_flash: Detected size(0k) smaller than the size in the binary image header(4096k). Probe failed.
assert failed: do_core_init startup.c:298 (flash_ret == ESP_OK)
Backtrace:0x40081b3e:0x3ffe3a800x400907fd:0x3ffe3aa0 0x4009739d:0x3ffe3ac0 0x400d25ea:0x3ffe3be0 0x400d2746:0x3ffe3c00 0x40081445:0x3ffe3c40 0x400794e0:0x3ffe3c80 |<-CORRUPTED
ELF file SHA256: 573ea08fdc881889
Rebooting...
Any ideas on what we can try to fix this issue?
Hello @wildbiotiger,
Thank you for trying the ESP-Hosted solution. This issue could be better answered with ESP-IDF team.
Suggestion: If any GPIOs attached, Can you remove all of them, try to erase flash and re-try flashing?
Can you please check this issue with https://github.com/espressif/esp-idf/issues?
I can post the issue there, but the issue is with the SDIO firmware provided in the latest release (v1.0.1). So, I am not able to modify any of the underlying code here. Would you be able to provide the source code that's trying to detect the SPI memory size in the current build? That would help me to frame the question better for the ESP-IDF team.
Other notes:
- SDIO is currently hooked up with the following pulled high through 10k resistors: MTMS, MTDI, MTDO, GPIO2, GPIO4
- When flashing, I pull MTMS, MTDI, MTDO, GPIO2, GPIO4, and GPIO0 low and toggle CHIP_PU to get it into the UART bootloader
- I have also burned the eFuse for VDD_SDIO to be set at 3.3V and verified using an oscilloscope that the voltage to the chip is 3.3V
- No voltage droops or other rail issues have been observed during flashing or anything else, it simply appears to be failing the memory size check
- In both the UART bootloader mode, and the SPI bootloader, the SPI memory size is unable to be detected as I showed above
- There are no other GPIOs connected besides the ones I listed above and the following connected to the SPI flash:
SD_DATA0 - (2) Slave Out
SD_DATA1 - (5) Slave In
SD_DATA2 - (7) Hold (IO3)
SD_DATA3 - (3) Write Protect (IO2)
SD_CLK - (6) SCK
SD_CMD - (1) Chip Select
Can you try to flash ESP-Hosted-FG solution, which is available to flash. There is not much difference other than Wi-Fi related handling. Basically, no change in SDIO or any other functionality.
You can build and flash ESP32 chipset using
ESP-IDF release/v4.0 with steps
- https://github.com/espressif/esp-hosted/blob/ESP-Hosted_MCU_Host/docs/Linux_based_host/Linux_based_readme.md#22-esp-idf-setup
- https://github.com/espressif/esp-hosted/blob/ESP-Hosted_MCU_Host/docs/Linux_based_host/SDIO_setup.md#222-source-compilation using SDIO
For flashing in fact you can use even IDF examples for SDIO slave driver. If it fails, ESP-IDF would be in better position to understand and resolve these issues quickly. Anyway, Please let us know if any of the above code flashes correctly.
Can you publish a build that would disable asserts in the code? That would help get me past THIS particular issue.
Forget about ESP-Hosted,
I want to understand why are you getting,
Detected size(0k) smaller than the size in the binary image header(4096k). Probe failed.
Can you try if SDIO slave example from ESP-IDF from branch, release/v4.0 is getting flashed without these kind of errors.
What my point is, if you have something non working at the ESP-IDF level itself, flashing ESP-Hosted would not be much useful and will complicate to understand what is exactly the problem.
Also do you have another chipset, where you can flash the firmware you had flashed? Possibly, It will help to differentiate the behaviour between working and non working things.
Can you please attach sdkconfig ? Also please check if this issue is related for you: https://github.com/espressif/esp-idf/issues/4829
@mantriyogesh Yes, I understand the issue lies primarily with ESP-IDF not ESP-Hosted. I have not tried the SDIO slave example yet, but I can pretty well trace the calls for the latest version of the ESP-IDF:
- esp_flash_spi_init.c:esp_flash_init_main:313
- esp_flash_api.c:esp_flash_get_size:294
- esp_flash_api.c:chip->chip_drv->detect_size:499
- spi_flash_chip_generic.c:spi_flash_chip_generic_detect_size:129
I would think the ID calculation for the SPI flash ID I see in the logs (0x1F8701) would spit out at least 2, but this doesn't seem to be the case. UNLESS the function errors out beforehand and NO size is returned.
0x1F8701 & 0xff // = 0x01
1 << 1 // = 2
//Why is chip_size still 0?
Based on the datasheet, it should be the following:
0x1F8701 & 0x1f00 // = 0x700
0x700 >> 8 // = 0x7
1 << 0x7 // = 128, which is not 32 Mbit, so not sure where to go here. Is this a JEDEC lookup table value?
SO, something in either case seems off.
Here's the current sdkconfig from the project.
I think I only had to edit the partition table to expand it for the debug statements and changed DIO to QIO (but I've tried it with DIO with no change in result).
#
# Automatically generated file. DO NOT EDIT.
# Espressif IoT Development Framework (ESP-IDF) Project Configuration
#
CONFIG_IDF_TARGET_ESP32=y
CONFIG_IDF_TARGET="esp32"
CONFIG_IDF_FIRMWARE_CHIP_ID=0x0000
#
# SDK tool configuration
#
CONFIG_SDK_TOOLPREFIX="xtensa-esp32-elf-"
CONFIG_APP_COMPILE_TIME_DATE=y
# CONFIG_APP_EXCLUDE_PROJECT_VER_VAR is not set
# CONFIG_APP_EXCLUDE_PROJECT_NAME_VAR is not set
CONFIG_APP_RETRIEVE_LEN_ELF_SHA=16
# CONFIG_BOOTLOADER_LOG_LEVEL_NONE is not set
# CONFIG_BOOTLOADER_LOG_LEVEL_ERROR is not set
# CONFIG_BOOTLOADER_LOG_LEVEL_WARN is not set
# CONFIG_BOOTLOADER_LOG_LEVEL_INFO is not set
# CONFIG_BOOTLOADER_LOG_LEVEL_DEBUG is not set
CONFIG_BOOTLOADER_LOG_LEVEL_VERBOSE=y
CONFIG_BOOTLOADER_LOG_LEVEL=5
CONFIG_BOOTLOADER_SPI_WP_PIN=7
CONFIG_BOOTLOADER_VDDSDIO_BOOST_1_9V=y
# CONFIG_BOOTLOADER_FACTORY_RESET is not set
# CONFIG_BOOTLOADER_APP_TEST is not set
CONFIG_BOOTLOADER_WDT_ENABLE=y
# CONFIG_BOOTLOADER_WDT_DISABLE_IN_USER_CODE is not set
CONFIG_BOOTLOADER_WDT_TIME_MS=9000
# CONFIG_BOOTLOADER_APP_ROLLBACK_ENABLE is not set
CONFIG_BOOTLOADER_FLASH_XMC_SUPPORT=y
# CONFIG_SECURE_SIGNED_APPS_NO_SECURE_BOOT is not set
# CONFIG_SECURE_BOOT_ENABLED is not set
# CONFIG_SECURE_FLASH_ENC_ENABLED is not set
CONFIG_ESPTOOLPY_BAUD_OTHER_VAL=115200
CONFIG_ESPTOOLPY_FLASHMODE_QIO=y
# CONFIG_ESPTOOLPY_FLASHMODE_QOUT is not set
# CONFIG_ESPTOOLPY_FLASHMODE_DIO is not set
# CONFIG_ESPTOOLPY_FLASHMODE_DOUT is not set
CONFIG_ESPTOOLPY_FLASHMODE="dio"
CONFIG_ESPTOOLPY_FLASHFREQ_80M=y
# CONFIG_ESPTOOLPY_FLASHFREQ_40M is not set
# CONFIG_ESPTOOLPY_FLASHFREQ_26M is not set
# CONFIG_ESPTOOLPY_FLASHFREQ_20M is not set
CONFIG_ESPTOOLPY_FLASHFREQ="80m"
# CONFIG_ESPTOOLPY_FLASHSIZE_1MB is not set
# CONFIG_ESPTOOLPY_FLASHSIZE_2MB is not set
CONFIG_ESPTOOLPY_FLASHSIZE_4MB=y
# CONFIG_ESPTOOLPY_FLASHSIZE_8MB is not set
# CONFIG_ESPTOOLPY_FLASHSIZE_16MB is not set
CONFIG_ESPTOOLPY_FLASHSIZE="4MB"
CONFIG_ESPTOOLPY_FLASHSIZE_DETECT=y
CONFIG_ESPTOOLPY_BEFORE_RESET=y
# CONFIG_ESPTOOLPY_BEFORE_NORESET is not set
CONFIG_ESPTOOLPY_BEFORE="default_reset"
CONFIG_ESPTOOLPY_AFTER_RESET=y
# CONFIG_ESPTOOLPY_AFTER_NORESET is not set
CONFIG_ESPTOOLPY_AFTER="hard_reset"
# CONFIG_ESPTOOLPY_MONITOR_BAUD_9600B is not set
# CONFIG_ESPTOOLPY_MONITOR_BAUD_57600B is not set
CONFIG_ESPTOOLPY_MONITOR_BAUD_115200B=y
# CONFIG_ESPTOOLPY_MONITOR_BAUD_230400B is not set
# CONFIG_ESPTOOLPY_MONITOR_BAUD_921600B is not set
# CONFIG_ESPTOOLPY_MONITOR_BAUD_2MB is not set
# CONFIG_ESPTOOLPY_MONITOR_BAUD_OTHER is not set
CONFIG_ESPTOOLPY_MONITOR_BAUD_OTHER_VAL=115200
CONFIG_ESPTOOLPY_MONITOR_BAUD=115200
# CONFIG_PARTITION_TABLE_SINGLE_APP is not set
CONFIG_PARTITION_TABLE_TWO_OTA=y
# CONFIG_PARTITION_TABLE_CUSTOM is not set
CONFIG_PARTITION_TABLE_CUSTOM_FILENAME="partitions.csv"
CONFIG_PARTITION_TABLE_FILENAME="partitions_two_ota.csv"
CONFIG_PARTITION_TABLE_OFFSET=0x10000
CONFIG_PARTITION_TABLE_MD5=y
CONFIG_ESP_SDIO_HOST_INTERFACE=y
# CONFIG_ESP_SPI_HOST_INTERFACE is not set
CONFIG_ESP_OTA_WORKAROUND=y
# CONFIG_ESP_SERIAL_DEBUG is not set
# CONFIG_ESP_WLAN_DEBUG is not set
# CONFIG_ESP_BT_DEBUG is not set
CONFIG_COMPILER_OPTIMIZATION_LEVEL_DEBUG=y
# CONFIG_COMPILER_OPTIMIZATION_LEVEL_RELEASE is not set
CONFIG_COMPILER_OPTIMIZATION_ASSERTIONS_ENABLE=y
# CONFIG_COMPILER_OPTIMIZATION_ASSERTIONS_SILENT is not set
# CONFIG_COMPILER_OPTIMIZATION_ASSERTIONS_DISABLE is not set
# CONFIG_COMPILER_CXX_EXCEPTIONS is not set
CONFIG_COMPILER_STACK_CHECK_MODE_NONE=y
# CONFIG_COMPILER_STACK_CHECK_MODE_NORM is not set
# CONFIG_COMPILER_STACK_CHECK_MODE_STRONG is not set
# CONFIG_COMPILER_STACK_CHECK_MODE_ALL is not set
# CONFIG_COMPILER_STACK_CHECK is not set
# CONFIG_COMPILER_WARN_WRITE_STRINGS is not set
# CONFIG_COMPILER_DISABLE_GCC8_WARNINGS is not set
# CONFIG_ESP32_APPTRACE_DEST_TRAX is not set
CONFIG_ESP32_APPTRACE_DEST_NONE=y
# CONFIG_ESP32_APPTRACE_ENABLE is not set
CONFIG_ESP32_APPTRACE_LOCK_ENABLE=y
CONFIG_BT_ENABLED=y
# CONFIG_BTDM_CTRL_MODE_BLE_ONLY is not set
# CONFIG_BTDM_CTRL_MODE_BR_EDR_ONLY is not set
CONFIG_BTDM_CTRL_MODE_BTDM=y
CONFIG_BTDM_CTRL_BLE_MAX_CONN=3
CONFIG_BTDM_CTRL_BR_EDR_MAX_ACL_CONN=2
CONFIG_BTDM_CTRL_BR_EDR_MAX_SYNC_CONN=0
# CONFIG_BTDM_CTRL_BR_EDR_SCO_DATA_PATH_HCI is not set
CONFIG_BTDM_CTRL_BR_EDR_SCO_DATA_PATH_PCM=y
CONFIG_BTDM_CTRL_BR_EDR_SCO_DATA_PATH_EFF=1
CONFIG_BTDM_CTRL_PCM_ROLE_EDGE_CONFIG=y
CONFIG_BTDM_CTRL_PCM_ROLE_MASTER=y
# CONFIG_BTDM_CTRL_PCM_ROLE_SLAVE is not set
CONFIG_BTDM_CTRL_PCM_POLAR_FALLING_EDGE=y
# CONFIG_BTDM_CTRL_PCM_POLAR_RISING_EDGE is not set
CONFIG_BTDM_CTRL_PCM_ROLE_EFF=0
CONFIG_BTDM_CTRL_PCM_POLAR_EFF=0
CONFIG_BTDM_CTRL_AUTO_LATENCY=y
CONFIG_BTDM_CTRL_AUTO_LATENCY_EFF=y
CONFIG_BTDM_CTRL_LEGACY_AUTH_VENDOR_EVT=y
CONFIG_BTDM_CTRL_LEGACY_AUTH_VENDOR_EVT_EFF=y
CONFIG_BTDM_CTRL_BLE_MAX_CONN_EFF=3
CONFIG_BTDM_CTRL_BR_EDR_MAX_ACL_CONN_EFF=2
CONFIG_BTDM_CTRL_BR_EDR_MAX_SYNC_CONN_EFF=0
CONFIG_BTDM_CTRL_PINNED_TO_CORE_0=y
# CONFIG_BTDM_CTRL_PINNED_TO_CORE_1 is not set
CONFIG_BTDM_CTRL_PINNED_TO_CORE=0
CONFIG_BTDM_CTRL_HCI_MODE_VHCI=y
# CONFIG_BTDM_CTRL_HCI_MODE_UART_H4 is not set
CONFIG_BTDM_MODEM_SLEEP=y
CONFIG_BTDM_MODEM_SLEEP_MODE_ORIG=y
# CONFIG_BTDM_MODEM_SLEEP_MODE_EVED is not set
CONFIG_BTDM_LPCLK_SEL_MAIN_XTAL=y
CONFIG_BTDM_BLE_DEFAULT_SCA_250PPM=y
CONFIG_BTDM_BLE_SLEEP_CLOCK_ACCURACY_INDEX_EFF=1
CONFIG_BTDM_BLE_SCAN_DUPL=y
CONFIG_BTDM_SCAN_DUPL_TYPE_DEVICE=y
# CONFIG_BTDM_SCAN_DUPL_TYPE_DATA is not set
# CONFIG_BTDM_SCAN_DUPL_TYPE_DATA_DEVICE is not set
CONFIG_BTDM_SCAN_DUPL_TYPE=0
CONFIG_BTDM_SCAN_DUPL_CACHE_SIZE=200
# CONFIG_BTDM_BLE_MESH_SCAN_DUPL_EN is not set
CONFIG_BTDM_CTRL_FULL_SCAN_SUPPORTED=y
CONFIG_BTDM_BLE_ADV_REPORT_FLOW_CTRL_SUPP=y
CONFIG_BTDM_BLE_ADV_REPORT_FLOW_CTRL_NUM=100
CONFIG_BTDM_BLE_ADV_REPORT_DISCARD_THRSHOLD=20
# CONFIG_BT_BLUEDROID_ENABLED is not set
# CONFIG_BT_NIMBLE_ENABLED is not set
CONFIG_BT_CONTROLLER_ONLY=y
CONFIG_BT_RESERVE_DRAM=0xdb5c
# CONFIG_BLE_MESH is not set
# CONFIG_ADC_FORCE_XPD_FSM is not set
CONFIG_ADC_DISABLE_DAC=y
# CONFIG_SPI_MASTER_IN_IRAM is not set
CONFIG_SPI_MASTER_ISR_IN_IRAM=y
# CONFIG_SPI_SLAVE_IN_IRAM is not set
CONFIG_SPI_SLAVE_ISR_IN_IRAM=y
# CONFIG_CAN_ISR_IN_IRAM is not set
# CONFIG_UART_ISR_IN_IRAM is not set
# CONFIG_EFUSE_CUSTOM_TABLE is not set
# CONFIG_EFUSE_VIRTUAL is not set
# CONFIG_EFUSE_CODE_SCHEME_COMPAT_NONE is not set
CONFIG_EFUSE_CODE_SCHEME_COMPAT_3_4=y
# CONFIG_EFUSE_CODE_SCHEME_COMPAT_REPEAT is not set
CONFIG_EFUSE_MAX_BLK_LEN=192
# CONFIG_ESP_TLS_SERVER is not set
CONFIG_ESP32_REV_MIN_0=y
# CONFIG_ESP32_REV_MIN_1 is not set
# CONFIG_ESP32_REV_MIN_2 is not set
# CONFIG_ESP32_REV_MIN_3 is not set
CONFIG_ESP32_REV_MIN=0
CONFIG_ESP32_DPORT_WORKAROUND=y
# CONFIG_ESP32_DEFAULT_CPU_FREQ_80 is not set
# CONFIG_ESP32_DEFAULT_CPU_FREQ_160 is not set
CONFIG_ESP32_DEFAULT_CPU_FREQ_240=y
CONFIG_ESP32_DEFAULT_CPU_FREQ_MHZ=240
# CONFIG_ESP32_SPIRAM_SUPPORT is not set
# CONFIG_ESP32_MEMMAP_TRACEMEM is not set
# CONFIG_ESP32_MEMMAP_TRACEMEM_TWOBANKS is not set
# CONFIG_ESP32_TRAX is not set
CONFIG_ESP32_TRACEMEM_RESERVE_DRAM=0x0
# CONFIG_ESP32_UNIVERSAL_MAC_ADDRESSES_TWO is not set
CONFIG_ESP32_UNIVERSAL_MAC_ADDRESSES_FOUR=y
CONFIG_ESP32_UNIVERSAL_MAC_ADDRESSES=4
# CONFIG_ESP32_ULP_COPROC_ENABLED is not set
CONFIG_ESP32_ULP_COPROC_RESERVE_MEM=0
# CONFIG_ESP32_PANIC_PRINT_HALT is not set
CONFIG_ESP32_PANIC_PRINT_REBOOT=y
# CONFIG_ESP32_PANIC_SILENT_REBOOT is not set
# CONFIG_ESP32_PANIC_GDBSTUB is not set
CONFIG_ESP32_DEBUG_OCDAWARE=y
CONFIG_ESP32_DEBUG_STUBS_ENABLE=y
CONFIG_ESP32_BROWNOUT_DET=y
CONFIG_ESP32_BROWNOUT_DET_LVL_SEL_0=y
# CONFIG_ESP32_BROWNOUT_DET_LVL_SEL_1 is not set
# CONFIG_ESP32_BROWNOUT_DET_LVL_SEL_2 is not set
# CONFIG_ESP32_BROWNOUT_DET_LVL_SEL_3 is not set
# CONFIG_ESP32_BROWNOUT_DET_LVL_SEL_4 is not set
# CONFIG_ESP32_BROWNOUT_DET_LVL_SEL_5 is not set
# CONFIG_ESP32_BROWNOUT_DET_LVL_SEL_6 is not set
# CONFIG_ESP32_BROWNOUT_DET_LVL_SEL_7 is not set
CONFIG_ESP32_BROWNOUT_DET_LVL=0
CONFIG_ESP32_REDUCE_PHY_TX_POWER=y
CONFIG_ESP32_TIME_SYSCALL_USE_RTC_FRC1=y
# CONFIG_ESP32_TIME_SYSCALL_USE_RTC is not set
# CONFIG_ESP32_TIME_SYSCALL_USE_FRC1 is not set
# CONFIG_ESP32_TIME_SYSCALL_USE_NONE is not set
CONFIG_ESP32_RTC_CLK_SRC_INT_RC=y
# CONFIG_ESP32_RTC_CLK_SRC_EXT_CRYS is not set
# CONFIG_ESP32_RTC_CLK_SRC_EXT_OSC is not set
# CONFIG_ESP32_RTC_CLK_SRC_INT_8MD256 is not set
CONFIG_ESP32_RTC_CLK_CAL_CYCLES=1024
CONFIG_ESP32_RTC_XTAL_CAL_RETRY=1
CONFIG_ESP32_DEEP_SLEEP_WAKEUP_DELAY=2000
CONFIG_ESP32_XTAL_FREQ_40=y
# CONFIG_ESP32_XTAL_FREQ_26 is not set
# CONFIG_ESP32_XTAL_FREQ_AUTO is not set
CONFIG_ESP32_XTAL_FREQ=40
# CONFIG_ESP32_DISABLE_BASIC_ROM_CONSOLE is not set
# CONFIG_ESP32_COMPATIBLE_PRE_V2_1_BOOTLOADERS is not set
# CONFIG_ESP32_COMPATIBLE_PRE_V3_1_BOOTLOADERS is not set
# CONFIG_ESP32_USE_FIXED_STATIC_RAM_SIZE is not set
CONFIG_ESP32_DPORT_DIS_INTERRUPT_LVL=5
# CONFIG_PM_ENABLE is not set
CONFIG_ADC_CAL_EFUSE_TP_ENABLE=y
CONFIG_ADC_CAL_EFUSE_VREF_ENABLE=y
CONFIG_ADC_CAL_LUT_ENABLE=y
# CONFIG_ESP_TIMER_PROFILING is not set
CONFIG_ESP_ERR_TO_NAME_LOOKUP=y
CONFIG_ESP_SYSTEM_EVENT_QUEUE_SIZE=32
CONFIG_ESP_SYSTEM_EVENT_TASK_STACK_SIZE=2304
CONFIG_ESP_MAIN_TASK_STACK_SIZE=3584
CONFIG_ESP_IPC_TASK_STACK_SIZE=1024
CONFIG_ESP_TIMER_TASK_STACK_SIZE=3584
CONFIG_ESP_CONSOLE_UART_DEFAULT=y
# CONFIG_ESP_CONSOLE_UART_CUSTOM is not set
# CONFIG_ESP_CONSOLE_UART_NONE is not set
CONFIG_ESP_CONSOLE_UART_NUM=0
CONFIG_ESP_CONSOLE_UART_BAUDRATE=115200
CONFIG_ESP_INT_WDT=y
CONFIG_ESP_INT_WDT_TIMEOUT_MS=600
CONFIG_ESP_INT_WDT_CHECK_CPU1=y
CONFIG_ESP_TASK_WDT=y
# CONFIG_ESP_TASK_WDT_PANIC is not set
CONFIG_ESP_TASK_WDT_TIMEOUT_S=5
CONFIG_ESP_TASK_WDT_CHECK_IDLE_TASK_CPU0=y
CONFIG_ESP_TASK_WDT_CHECK_IDLE_TASK_CPU1=y
CONFIG_ETH_USE_ESP32_EMAC=y
CONFIG_ETH_PHY_INTERFACE_RMII=y
# CONFIG_ETH_PHY_INTERFACE_MII is not set
CONFIG_ETH_RMII_CLK_INPUT=y
# CONFIG_ETH_RMII_CLK_OUTPUT is not set
CONFIG_ETH_RMII_CLK_IN_GPIO=0
CONFIG_ETH_DMA_BUFFER_SIZE=512
CONFIG_ETH_DMA_RX_BUFFER_NUM=10
CONFIG_ETH_DMA_TX_BUFFER_NUM=10
CONFIG_ETH_USE_SPI_ETHERNET=y
CONFIG_ETH_SPI_ETHERNET_DM9051=y
# CONFIG_ESP_EVENT_LOOP_PROFILING is not set
CONFIG_ESP_EVENT_POST_FROM_ISR=y
CONFIG_ESP_EVENT_POST_FROM_IRAM_ISR=y
CONFIG_ESP_HTTP_CLIENT_ENABLE_HTTPS=y
# CONFIG_ESP_HTTP_CLIENT_ENABLE_BASIC_AUTH is not set
CONFIG_HTTPD_MAX_REQ_HDR_LEN=512
CONFIG_HTTPD_MAX_URI_LEN=512
CONFIG_HTTPD_ERR_RESP_NO_DELAY=y
CONFIG_HTTPD_PURGE_BUF_LEN=32
# CONFIG_HTTPD_LOG_PURGE_DATA is not set
# CONFIG_OTA_ALLOW_HTTP is not set
# CONFIG_ESP_HTTPS_SERVER_ENABLE is not set
CONFIG_ESP32_WIFI_SW_COEXIST_ENABLE=y
CONFIG_ESP32_WIFI_STATIC_RX_BUFFER_NUM=16
CONFIG_ESP32_WIFI_DYNAMIC_RX_BUFFER_NUM=32
# CONFIG_ESP32_WIFI_STATIC_TX_BUFFER is not set
CONFIG_ESP32_WIFI_DYNAMIC_TX_BUFFER=y
CONFIG_ESP32_WIFI_TX_BUFFER_TYPE=1
CONFIG_ESP32_WIFI_DYNAMIC_TX_BUFFER_NUM=64
# CONFIG_ESP32_WIFI_CSI_ENABLED is not set
CONFIG_ESP32_WIFI_AMPDU_TX_ENABLED=y
CONFIG_ESP32_WIFI_TX_BA_WIN=6
CONFIG_ESP32_WIFI_AMPDU_RX_ENABLED=y
CONFIG_ESP32_WIFI_RX_BA_WIN=6
# CONFIG_ESP32_WIFI_NVS_ENABLED is not set
# CONFIG_ESP32_WIFI_TASK_PINNED_TO_CORE_0 is not set
CONFIG_ESP32_WIFI_TASK_PINNED_TO_CORE_1=y
CONFIG_ESP32_WIFI_SOFTAP_BEACON_MAX_LEN=752
CONFIG_ESP32_WIFI_MGMT_SBUF_NUM=32
# CONFIG_ESP32_WIFI_DEBUG_LOG_ENABLE is not set
CONFIG_ESP32_WIFI_IRAM_OPT=y
CONFIG_ESP32_WIFI_RX_IRAM_OPT=y
CONFIG_ESP32_WIFI_ENABLE_WPA3_SAE=y
CONFIG_ESP32_PHY_CALIBRATION_AND_DATA_STORAGE=y
# CONFIG_ESP32_PHY_INIT_DATA_IN_PARTITION is not set
CONFIG_ESP32_PHY_MAX_WIFI_TX_POWER=20
CONFIG_ESP32_PHY_MAX_TX_POWER=20
# CONFIG_ESP32_ENABLE_COREDUMP_TO_FLASH is not set
# CONFIG_ESP32_ENABLE_COREDUMP_TO_UART is not set
CONFIG_ESP32_ENABLE_COREDUMP_TO_NONE=y
# CONFIG_ESP32_ENABLE_COREDUMP is not set
# CONFIG_FATFS_CODEPAGE_DYNAMIC is not set
CONFIG_FATFS_CODEPAGE_437=y
# CONFIG_FATFS_CODEPAGE_720 is not set
# CONFIG_FATFS_CODEPAGE_737 is not set
# CONFIG_FATFS_CODEPAGE_771 is not set
# CONFIG_FATFS_CODEPAGE_775 is not set
# CONFIG_FATFS_CODEPAGE_850 is not set
# CONFIG_FATFS_CODEPAGE_852 is not set
# CONFIG_FATFS_CODEPAGE_855 is not set
# CONFIG_FATFS_CODEPAGE_857 is not set
# CONFIG_FATFS_CODEPAGE_860 is not set
# CONFIG_FATFS_CODEPAGE_861 is not set
# CONFIG_FATFS_CODEPAGE_862 is not set
# CONFIG_FATFS_CODEPAGE_863 is not set
# CONFIG_FATFS_CODEPAGE_864 is not set
# CONFIG_FATFS_CODEPAGE_865 is not set
# CONFIG_FATFS_CODEPAGE_866 is not set
# CONFIG_FATFS_CODEPAGE_869 is not set
# CONFIG_FATFS_CODEPAGE_932 is not set
# CONFIG_FATFS_CODEPAGE_936 is not set
# CONFIG_FATFS_CODEPAGE_949 is not set
# CONFIG_FATFS_CODEPAGE_950 is not set
CONFIG_FATFS_CODEPAGE=437
CONFIG_FATFS_LFN_NONE=y
# CONFIG_FATFS_LFN_HEAP is not set
# CONFIG_FATFS_LFN_STACK is not set
CONFIG_FATFS_FS_LOCK=0
CONFIG_FATFS_TIMEOUT_MS=10000
CONFIG_FATFS_PER_FILE_CACHE=y
CONFIG_FMB_MASTER_TIMEOUT_MS_RESPOND=150
CONFIG_FMB_MASTER_DELAY_MS_CONVERT=200
CONFIG_FMB_QUEUE_LENGTH=20
CONFIG_FMB_SERIAL_TASK_STACK_SIZE=2048
CONFIG_FMB_SERIAL_BUF_SIZE=256
CONFIG_FMB_SERIAL_TASK_PRIO=10
# CONFIG_FMB_PORT_TASK_AFFINITY_NO_AFFINITY is not set
CONFIG_FMB_PORT_TASK_AFFINITY_CPU0=y
# CONFIG_FMB_PORT_TASK_AFFINITY_CPU1 is not set
CONFIG_FMB_PORT_TASK_AFFINITY=0x0
# CONFIG_FMB_CONTROLLER_SLAVE_ID_SUPPORT is not set
CONFIG_FMB_CONTROLLER_NOTIFY_TIMEOUT=20
CONFIG_FMB_CONTROLLER_NOTIFY_QUEUE_SIZE=20
CONFIG_FMB_CONTROLLER_STACK_SIZE=4096
CONFIG_FMB_EVENT_QUEUE_TIMEOUT=20
CONFIG_FMB_TIMER_PORT_ENABLED=y
CONFIG_FMB_TIMER_GROUP=0
CONFIG_FMB_TIMER_INDEX=0
CONFIG_FMB_MASTER_TIMER_GROUP=0
CONFIG_FMB_MASTER_TIMER_INDEX=0
# CONFIG_FREERTOS_UNICORE is not set
CONFIG_FREERTOS_NO_AFFINITY=0x7FFFFFFF
CONFIG_FREERTOS_CORETIMER_0=y
# CONFIG_FREERTOS_CORETIMER_1 is not set
CONFIG_FREERTOS_HZ=400
CONFIG_FREERTOS_ASSERT_ON_UNTESTED_FUNCTION=y
# CONFIG_FREERTOS_CHECK_STACKOVERFLOW_NONE is not set
# CONFIG_FREERTOS_CHECK_STACKOVERFLOW_PTRVAL is not set
CONFIG_FREERTOS_CHECK_STACKOVERFLOW_CANARY=y
# CONFIG_FREERTOS_WATCHPOINT_END_OF_STACK is not set
CONFIG_FREERTOS_INTERRUPT_BACKTRACE=y
CONFIG_FREERTOS_THREAD_LOCAL_STORAGE_POINTERS=1
CONFIG_FREERTOS_ASSERT_FAIL_ABORT=y
# CONFIG_FREERTOS_ASSERT_FAIL_PRINT_CONTINUE is not set
# CONFIG_FREERTOS_ASSERT_DISABLE is not set
CONFIG_FREERTOS_IDLE_TASK_STACKSIZE=1536
CONFIG_FREERTOS_ISR_STACKSIZE=1536
# CONFIG_FREERTOS_LEGACY_HOOKS is not set
CONFIG_FREERTOS_MAX_TASK_NAME_LEN=16
# CONFIG_FREERTOS_SUPPORT_STATIC_ALLOCATION is not set
CONFIG_FREERTOS_TIMER_TASK_PRIORITY=1
CONFIG_FREERTOS_TIMER_TASK_STACK_DEPTH=2048
CONFIG_FREERTOS_TIMER_QUEUE_LENGTH=10
CONFIG_FREERTOS_QUEUE_REGISTRY_SIZE=0
# CONFIG_FREERTOS_USE_TRACE_FACILITY is not set
# CONFIG_FREERTOS_GENERATE_RUN_TIME_STATS is not set
# CONFIG_FREERTOS_DEBUG_INTERNALS is not set
CONFIG_FREERTOS_TASK_FUNCTION_WRAPPER=y
CONFIG_FREERTOS_CHECK_MUTEX_GIVEN_BY_OWNER=y
# CONFIG_FREERTOS_CHECK_PORT_CRITICAL_COMPLIANCE is not set
CONFIG_HEAP_POISONING_DISABLED=y
# CONFIG_HEAP_POISONING_LIGHT is not set
# CONFIG_HEAP_POISONING_COMPREHENSIVE is not set
CONFIG_HEAP_TRACING_OFF=y
# CONFIG_HEAP_TRACING_STANDALONE is not set
# CONFIG_HEAP_TRACING_TOHOST is not set
# CONFIG_HEAP_TRACING is not set
# CONFIG_LOG_DEFAULT_LEVEL_NONE is not set
# CONFIG_LOG_DEFAULT_LEVEL_ERROR is not set
# CONFIG_LOG_DEFAULT_LEVEL_WARN is not set
# CONFIG_LOG_DEFAULT_LEVEL_INFO is not set
# CONFIG_LOG_DEFAULT_LEVEL_DEBUG is not set
CONFIG_LOG_DEFAULT_LEVEL_VERBOSE=y
CONFIG_LOG_DEFAULT_LEVEL=5
CONFIG_LOG_COLORS=y
CONFIG_LWIP_LOCAL_HOSTNAME="espressif"
# CONFIG_LWIP_L2_TO_L3_COPY is not set
# CONFIG_LWIP_IRAM_OPTIMIZATION is not set
CONFIG_LWIP_TIMERS_ONDEMAND=y
CONFIG_LWIP_MAX_SOCKETS=10
# CONFIG_LWIP_USE_ONLY_LWIP_SELECT is not set
# CONFIG_LWIP_SO_LINGER is not set
CONFIG_LWIP_SO_REUSE=y
CONFIG_LWIP_SO_REUSE_RXTOALL=y
# CONFIG_LWIP_SO_RCVBUF is not set
CONFIG_LWIP_IP4_FRAG=y
CONFIG_LWIP_IP6_FRAG=y
# CONFIG_LWIP_IP4_REASSEMBLY is not set
# CONFIG_LWIP_IP6_REASSEMBLY is not set
# CONFIG_LWIP_STATS is not set
# CONFIG_LWIP_ETHARP_TRUST_IP_MAC is not set
CONFIG_LWIP_ESP_GRATUITOUS_ARP=y
CONFIG_LWIP_GARP_TMR_INTERVAL=60
CONFIG_LWIP_TCPIP_RECVMBOX_SIZE=32
CONFIG_LWIP_DHCP_DOES_ARP_CHECK=y
# CONFIG_LWIP_DHCP_RESTORE_LAST_IP is not set
CONFIG_LWIP_DHCPS_LEASE_UNIT=60
CONFIG_LWIP_DHCPS_MAX_STATION_NUM=8
# CONFIG_LWIP_AUTOIP is not set
# CONFIG_LWIP_IPV6_AUTOCONFIG is not set
CONFIG_LWIP_NETIF_LOOPBACK=y
CONFIG_LWIP_LOOPBACK_MAX_PBUFS=8
CONFIG_LWIP_TCP_ISN_HOOK=y
CONFIG_LWIP_MAX_ACTIVE_TCP=16
CONFIG_LWIP_MAX_LISTENING_TCP=16
CONFIG_LWIP_TCP_HIGH_SPEED_RETRANSMISSION=y
CONFIG_LWIP_TCP_MAXRTX=12
CONFIG_LWIP_TCP_SYNMAXRTX=12
CONFIG_LWIP_TCP_MSS=1440
CONFIG_LWIP_TCP_MSL=60000
CONFIG_LWIP_TCP_SND_BUF_DEFAULT=5744
CONFIG_LWIP_TCP_WND_DEFAULT=5744
CONFIG_LWIP_TCP_RECVMBOX_SIZE=6
CONFIG_LWIP_TCP_QUEUE_OOSEQ=y
# CONFIG_LWIP_TCP_KEEP_CONNECTION_WHEN_IP_CHANGES is not set
CONFIG_LWIP_TCP_OVERSIZE_MSS=y
# CONFIG_LWIP_TCP_OVERSIZE_QUARTER_MSS is not set
# CONFIG_LWIP_TCP_OVERSIZE_DISABLE is not set
CONFIG_LWIP_TCP_RTO_TIME=1500
CONFIG_LWIP_MAX_UDP_PCBS=16
CONFIG_LWIP_UDP_RECVMBOX_SIZE=6
CONFIG_LWIP_TCPIP_TASK_STACK_SIZE=3072
CONFIG_LWIP_TCPIP_TASK_AFFINITY_NO_AFFINITY=y
# CONFIG_LWIP_TCPIP_TASK_AFFINITY_CPU0 is not set
# CONFIG_LWIP_TCPIP_TASK_AFFINITY_CPU1 is not set
CONFIG_LWIP_TCPIP_TASK_AFFINITY=0x7FFFFFFF
# CONFIG_LWIP_PPP_SUPPORT is not set
CONFIG_LWIP_IPV6_MEMP_NUM_ND6_QUEUE=3
CONFIG_LWIP_IPV6_ND6_NUM_NEIGHBORS=5
# CONFIG_LWIP_MULTICAST_PING is not set
# CONFIG_LWIP_BROADCAST_PING is not set
CONFIG_LWIP_MAX_RAW_PCBS=16
CONFIG_LWIP_DHCP_MAX_NTP_SERVERS=1
CONFIG_LWIP_SNTP_UPDATE_DELAY=3600000
CONFIG_MBEDTLS_INTERNAL_MEM_ALLOC=y
# CONFIG_MBEDTLS_DEFAULT_MEM_ALLOC is not set
# CONFIG_MBEDTLS_CUSTOM_MEM_ALLOC is not set
CONFIG_MBEDTLS_ASYMMETRIC_CONTENT_LEN=y
CONFIG_MBEDTLS_SSL_IN_CONTENT_LEN=16384
CONFIG_MBEDTLS_SSL_OUT_CONTENT_LEN=4096
# CONFIG_MBEDTLS_DEBUG is not set
# CONFIG_MBEDTLS_ECP_RESTARTABLE is not set
# CONFIG_MBEDTLS_CMAC_C is not set
CONFIG_MBEDTLS_HARDWARE_AES=y
# CONFIG_MBEDTLS_HARDWARE_MPI is not set
CONFIG_MBEDTLS_HARDWARE_SHA=y
CONFIG_MBEDTLS_HAVE_TIME=y
# CONFIG_MBEDTLS_HAVE_TIME_DATE is not set
CONFIG_MBEDTLS_TLS_SERVER_AND_CLIENT=y
# CONFIG_MBEDTLS_TLS_SERVER_ONLY is not set
# CONFIG_MBEDTLS_TLS_CLIENT_ONLY is not set
# CONFIG_MBEDTLS_TLS_DISABLED is not set
CONFIG_MBEDTLS_TLS_SERVER=y
CONFIG_MBEDTLS_TLS_CLIENT=y
CONFIG_MBEDTLS_TLS_ENABLED=y
# CONFIG_MBEDTLS_PSK_MODES is not set
CONFIG_MBEDTLS_KEY_EXCHANGE_RSA=y
CONFIG_MBEDTLS_KEY_EXCHANGE_DHE_RSA=y
CONFIG_MBEDTLS_KEY_EXCHANGE_ELLIPTIC_CURVE=y
CONFIG_MBEDTLS_KEY_EXCHANGE_ECDHE_RSA=y
CONFIG_MBEDTLS_KEY_EXCHANGE_ECDHE_ECDSA=y
CONFIG_MBEDTLS_KEY_EXCHANGE_ECDH_ECDSA=y
CONFIG_MBEDTLS_KEY_EXCHANGE_ECDH_RSA=y
CONFIG_MBEDTLS_SSL_RENEGOTIATION=y
# CONFIG_MBEDTLS_SSL_PROTO_SSL3 is not set
CONFIG_MBEDTLS_SSL_PROTO_TLS1=y
CONFIG_MBEDTLS_SSL_PROTO_TLS1_1=y
CONFIG_MBEDTLS_SSL_PROTO_TLS1_2=y
# CONFIG_MBEDTLS_SSL_PROTO_DTLS is not set
CONFIG_MBEDTLS_SSL_ALPN=y
CONFIG_MBEDTLS_CLIENT_SSL_SESSION_TICKETS=y
CONFIG_MBEDTLS_SERVER_SSL_SESSION_TICKETS=y
CONFIG_MBEDTLS_AES_C=y
# CONFIG_MBEDTLS_CAMELLIA_C is not set
# CONFIG_MBEDTLS_DES_C is not set
CONFIG_MBEDTLS_RC4_DISABLED=y
# CONFIG_MBEDTLS_RC4_ENABLED_NO_DEFAULT is not set
# CONFIG_MBEDTLS_RC4_ENABLED is not set
# CONFIG_MBEDTLS_BLOWFISH_C is not set
# CONFIG_MBEDTLS_XTEA_C is not set
CONFIG_MBEDTLS_CCM_C=y
CONFIG_MBEDTLS_GCM_C=y
# CONFIG_MBEDTLS_RIPEMD160_C is not set
CONFIG_MBEDTLS_PEM_PARSE_C=y
CONFIG_MBEDTLS_PEM_WRITE_C=y
CONFIG_MBEDTLS_X509_CRL_PARSE_C=y
CONFIG_MBEDTLS_X509_CSR_PARSE_C=y
CONFIG_MBEDTLS_ECP_C=y
CONFIG_MBEDTLS_ECDH_C=y
CONFIG_MBEDTLS_ECDSA_C=y
CONFIG_MBEDTLS_ECP_DP_SECP192R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP224R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP256R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP384R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP521R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP192K1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP224K1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_SECP256K1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_BP256R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_BP384R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_BP512R1_ENABLED=y
CONFIG_MBEDTLS_ECP_DP_CURVE25519_ENABLED=y
CONFIG_MBEDTLS_ECP_NIST_OPTIM=y
CONFIG_MDNS_MAX_SERVICES=10
CONFIG_MQTT_PROTOCOL_311=y
CONFIG_MQTT_TRANSPORT_SSL=y
CONFIG_MQTT_TRANSPORT_WEBSOCKET=y
CONFIG_MQTT_TRANSPORT_WEBSOCKET_SECURE=y
# CONFIG_MQTT_USE_CUSTOM_CONFIG is not set
# CONFIG_MQTT_TASK_CORE_SELECTION_ENABLED is not set
# CONFIG_MQTT_CUSTOM_OUTBOX is not set
CONFIG_NEWLIB_STDOUT_LINE_ENDING_CRLF=y
# CONFIG_NEWLIB_STDOUT_LINE_ENDING_LF is not set
# CONFIG_NEWLIB_STDOUT_LINE_ENDING_CR is not set
# CONFIG_NEWLIB_STDIN_LINE_ENDING_CRLF is not set
# CONFIG_NEWLIB_STDIN_LINE_ENDING_LF is not set
CONFIG_NEWLIB_STDIN_LINE_ENDING_CR=y
# CONFIG_NEWLIB_NANO_FORMAT is not set
# CONFIG_OPENSSL_DEBUG is not set
# CONFIG_OPENSSL_ASSERT_DO_NOTHING is not set
CONFIG_OPENSSL_ASSERT_EXIT=y
CONFIG_PTHREAD_TASK_PRIO_DEFAULT=5
CONFIG_PTHREAD_TASK_STACK_SIZE_DEFAULT=3072
CONFIG_PTHREAD_STACK_MIN=768
CONFIG_PTHREAD_DEFAULT_CORE_NO_AFFINITY=y
# CONFIG_PTHREAD_DEFAULT_CORE_0 is not set
# CONFIG_PTHREAD_DEFAULT_CORE_1 is not set
CONFIG_PTHREAD_TASK_CORE_DEFAULT=-1
CONFIG_PTHREAD_TASK_NAME_DEFAULT="pthread"
# CONFIG_SPI_FLASH_VERIFY_WRITE is not set
# CONFIG_SPI_FLASH_ENABLE_COUNTERS is not set
CONFIG_SPI_FLASH_ROM_DRIVER_PATCH=y
CONFIG_SPI_FLASH_DANGEROUS_WRITE_ABORTS=y
# CONFIG_SPI_FLASH_DANGEROUS_WRITE_FAILS is not set
# CONFIG_SPI_FLASH_DANGEROUS_WRITE_ALLOWED is not set
# CONFIG_SPI_FLASH_USE_LEGACY_IMPL is not set
# CONFIG_SPI_FLASH_BYPASS_BLOCK_ERASE is not set
CONFIG_SPI_FLASH_YIELD_DURING_ERASE=y
CONFIG_SPI_FLASH_ERASE_YIELD_DURATION_MS=20
CONFIG_SPI_FLASH_ERASE_YIELD_TICKS=1
# CONFIG_SPI_FLASH_SIZE_OVERRIDE is not set
CONFIG_SPI_FLASH_SUPPORT_ISSI_CHIP=y
CONFIG_SPI_FLASH_SUPPORT_GD_CHIP=y
CONFIG_SPI_FLASH_ENABLE_ENCRYPTED_READ_WRITE=y
CONFIG_SPIFFS_MAX_PARTITIONS=3
CONFIG_SPIFFS_CACHE=y
CONFIG_SPIFFS_CACHE_WR=y
# CONFIG_SPIFFS_CACHE_STATS is not set
CONFIG_SPIFFS_PAGE_CHECK=y
CONFIG_SPIFFS_GC_MAX_RUNS=10
# CONFIG_SPIFFS_GC_STATS is not set
CONFIG_SPIFFS_PAGE_SIZE=256
CONFIG_SPIFFS_OBJ_NAME_LEN=32
CONFIG_SPIFFS_USE_MAGIC=y
CONFIG_SPIFFS_USE_MAGIC_LENGTH=y
CONFIG_SPIFFS_META_LENGTH=4
CONFIG_SPIFFS_USE_MTIME=y
# CONFIG_SPIFFS_DBG is not set
# CONFIG_SPIFFS_API_DBG is not set
# CONFIG_SPIFFS_GC_DBG is not set
# CONFIG_SPIFFS_CACHE_DBG is not set
# CONFIG_SPIFFS_CHECK_DBG is not set
# CONFIG_SPIFFS_TEST_VISUALISATION is not set
CONFIG_NETIF_IP_LOST_TIMER_INTERVAL=120
CONFIG_TCPIP_LWIP=y
CONFIG_UNITY_ENABLE_FLOAT=y
CONFIG_UNITY_ENABLE_DOUBLE=y
# CONFIG_UNITY_ENABLE_COLOR is not set
CONFIG_UNITY_ENABLE_IDF_TEST_RUNNER=y
# CONFIG_UNITY_ENABLE_FIXTURE is not set
# CONFIG_UNITY_ENABLE_BACKTRACE_ON_FAIL is not set
CONFIG_VFS_SUPPRESS_SELECT_DEBUG_OUTPUT=y
CONFIG_VFS_SUPPORT_TERMIOS=y
CONFIG_SEMIHOSTFS_MAX_MOUNT_POINTS=1
CONFIG_SEMIHOSTFS_HOST_PATH_MAX_LEN=128
# CONFIG_WL_SECTOR_SIZE_512 is not set
CONFIG_WL_SECTOR_SIZE_4096=y
CONFIG_WL_SECTOR_SIZE=4096
CONFIG_WIFI_PROV_SCAN_MAX_ENTRIES=16
CONFIG_WIFI_PROV_AUTOSTOP_TIMEOUT=30
CONFIG_WPA_MBEDTLS_CRYPTO=y
# CONFIG_WPA_WPS_STRICT is not set
# CONFIG_WPA_DEBUG_PRINT is not set
# CONFIG_LEGACY_INCLUDE_COMMON_HEADERS is not set
# Deprecated options for backward compatibility
CONFIG_TOOLPREFIX="xtensa-esp32-elf-"
# CONFIG_LOG_BOOTLOADER_LEVEL_NONE is not set
# CONFIG_LOG_BOOTLOADER_LEVEL_ERROR is not set
# CONFIG_LOG_BOOTLOADER_LEVEL_WARN is not set
# CONFIG_LOG_BOOTLOADER_LEVEL_INFO is not set
# CONFIG_LOG_BOOTLOADER_LEVEL_DEBUG is not set
CONFIG_LOG_BOOTLOADER_LEVEL_VERBOSE=y
CONFIG_LOG_BOOTLOADER_LEVEL=5
# CONFIG_APP_ROLLBACK_ENABLE is not set
# CONFIG_FLASH_ENCRYPTION_ENABLED is not set
CONFIG_FLASHMODE_QIO=y
# CONFIG_FLASHMODE_QOUT is not set
# CONFIG_FLASHMODE_DIO is not set
# CONFIG_FLASHMODE_DOUT is not set
# CONFIG_MONITOR_BAUD_9600B is not set
# CONFIG_MONITOR_BAUD_57600B is not set
CONFIG_MONITOR_BAUD_115200B=y
# CONFIG_MONITOR_BAUD_230400B is not set
# CONFIG_MONITOR_BAUD_921600B is not set
# CONFIG_MONITOR_BAUD_2MB is not set
# CONFIG_MONITOR_BAUD_OTHER is not set
CONFIG_MONITOR_BAUD_OTHER_VAL=115200
CONFIG_MONITOR_BAUD=115200
CONFIG_OPTIMIZATION_LEVEL_DEBUG=y
# CONFIG_OPTIMIZATION_LEVEL_RELEASE is not set
CONFIG_OPTIMIZATION_ASSERTIONS_ENABLED=y
# CONFIG_OPTIMIZATION_ASSERTIONS_SILENT is not set
# CONFIG_OPTIMIZATION_ASSERTIONS_DISABLED is not set
# CONFIG_CXX_EXCEPTIONS is not set
CONFIG_STACK_CHECK_NONE=y
# CONFIG_STACK_CHECK_NORM is not set
# CONFIG_STACK_CHECK_STRONG is not set
# CONFIG_STACK_CHECK_ALL is not set
# CONFIG_STACK_CHECK is not set
# CONFIG_WARN_WRITE_STRINGS is not set
# CONFIG_DISABLE_GCC8_WARNINGS is not set
# CONFIG_BTDM_CONTROLLER_MODE_BLE_ONLY is not set
# CONFIG_BTDM_CONTROLLER_MODE_BR_EDR_ONLY is not set
CONFIG_BTDM_CONTROLLER_MODE_BTDM=y
CONFIG_BTDM_CONTROLLER_BLE_MAX_CONN=3
CONFIG_BTDM_CONTROLLER_BR_EDR_MAX_ACL_CONN=2
CONFIG_BTDM_CONTROLLER_BR_EDR_MAX_SYNC_CONN=0
CONFIG_BTDM_CONTROLLER_BLE_MAX_CONN_EFF=3
CONFIG_BTDM_CONTROLLER_BR_EDR_MAX_ACL_CONN_EFF=2
CONFIG_BTDM_CONTROLLER_BR_EDR_MAX_SYNC_CONN_EFF=0
CONFIG_BTDM_CONTROLLER_PINNED_TO_CORE=0
CONFIG_BTDM_CONTROLLER_HCI_MODE_VHCI=y
# CONFIG_BTDM_CONTROLLER_HCI_MODE_UART_H4 is not set
CONFIG_BTDM_CONTROLLER_MODEM_SLEEP=y
CONFIG_BLE_SCAN_DUPLICATE=y
CONFIG_SCAN_DUPLICATE_BY_DEVICE_ADDR=y
# CONFIG_SCAN_DUPLICATE_BY_ADV_DATA is not set
# CONFIG_SCAN_DUPLICATE_BY_ADV_DATA_AND_DEVICE_ADDR is not set
CONFIG_SCAN_DUPLICATE_TYPE=0
CONFIG_DUPLICATE_SCAN_CACHE_SIZE=200
# CONFIG_BLE_MESH_SCAN_DUPLICATE_EN is not set
CONFIG_BTDM_CONTROLLER_FULL_SCAN_SUPPORTED=y
CONFIG_BLE_ADV_REPORT_FLOW_CONTROL_SUPPORTED=y
CONFIG_BLE_ADV_REPORT_FLOW_CONTROL_NUM=100
CONFIG_BLE_ADV_REPORT_DISCARD_THRSHOLD=20
# CONFIG_BLUEDROID_ENABLED is not set
# CONFIG_NIMBLE_ENABLED is not set
CONFIG_ADC2_DISABLE_DAC=y
# CONFIG_SPIRAM_SUPPORT is not set
# CONFIG_MEMMAP_TRACEMEM is not set
# CONFIG_MEMMAP_TRACEMEM_TWOBANKS is not set
CONFIG_TRACEMEM_RESERVE_DRAM=0x0
# CONFIG_TWO_UNIVERSAL_MAC_ADDRESS is not set
CONFIG_FOUR_UNIVERSAL_MAC_ADDRESS=y
CONFIG_NUMBER_OF_UNIVERSAL_MAC_ADDRESS=4
# CONFIG_ULP_COPROC_ENABLED is not set
CONFIG_ULP_COPROC_RESERVE_MEM=0
CONFIG_BROWNOUT_DET=y
CONFIG_BROWNOUT_DET_LVL_SEL_0=y
# CONFIG_BROWNOUT_DET_LVL_SEL_1 is not set
# CONFIG_BROWNOUT_DET_LVL_SEL_2 is not set
# CONFIG_BROWNOUT_DET_LVL_SEL_3 is not set
# CONFIG_BROWNOUT_DET_LVL_SEL_4 is not set
# CONFIG_BROWNOUT_DET_LVL_SEL_5 is not set
# CONFIG_BROWNOUT_DET_LVL_SEL_6 is not set
# CONFIG_BROWNOUT_DET_LVL_SEL_7 is not set
CONFIG_BROWNOUT_DET_LVL=0
CONFIG_REDUCE_PHY_TX_POWER=y
CONFIG_ESP32_RTC_CLOCK_SOURCE_INTERNAL_RC=y
# CONFIG_ESP32_RTC_CLOCK_SOURCE_EXTERNAL_CRYSTAL is not set
# CONFIG_ESP32_RTC_CLOCK_SOURCE_EXTERNAL_OSC is not set
# CONFIG_ESP32_RTC_CLOCK_SOURCE_INTERNAL_8MD256 is not set
# CONFIG_DISABLE_BASIC_ROM_CONSOLE is not set
# CONFIG_COMPATIBLE_PRE_V2_1_BOOTLOADERS is not set
CONFIG_SYSTEM_EVENT_QUEUE_SIZE=32
CONFIG_SYSTEM_EVENT_TASK_STACK_SIZE=2304
CONFIG_MAIN_TASK_STACK_SIZE=3584
CONFIG_IPC_TASK_STACK_SIZE=1024
CONFIG_TIMER_TASK_STACK_SIZE=3584
CONFIG_CONSOLE_UART_DEFAULT=y
# CONFIG_CONSOLE_UART_CUSTOM is not set
# CONFIG_CONSOLE_UART_NONE is not set
CONFIG_CONSOLE_UART_NUM=0
CONFIG_CONSOLE_UART_BAUDRATE=115200
CONFIG_INT_WDT=y
CONFIG_INT_WDT_TIMEOUT_MS=600
CONFIG_INT_WDT_CHECK_CPU1=y
CONFIG_TASK_WDT=y
# CONFIG_TASK_WDT_PANIC is not set
CONFIG_TASK_WDT_TIMEOUT_S=5
CONFIG_TASK_WDT_CHECK_IDLE_TASK_CPU0=y
CONFIG_TASK_WDT_CHECK_IDLE_TASK_CPU1=y
# CONFIG_EVENT_LOOP_PROFILING is not set
CONFIG_POST_EVENTS_FROM_ISR=y
CONFIG_POST_EVENTS_FROM_IRAM_ISR=y
CONFIG_SW_COEXIST_ENABLE=y
CONFIG_MB_MASTER_TIMEOUT_MS_RESPOND=150
CONFIG_MB_MASTER_DELAY_MS_CONVERT=200
CONFIG_MB_QUEUE_LENGTH=20
CONFIG_MB_SERIAL_TASK_STACK_SIZE=2048
CONFIG_MB_SERIAL_BUF_SIZE=256
CONFIG_MB_SERIAL_TASK_PRIO=10
# CONFIG_MB_CONTROLLER_SLAVE_ID_SUPPORT is not set
CONFIG_MB_CONTROLLER_NOTIFY_TIMEOUT=20
CONFIG_MB_CONTROLLER_NOTIFY_QUEUE_SIZE=20
CONFIG_MB_CONTROLLER_STACK_SIZE=4096
CONFIG_MB_EVENT_QUEUE_TIMEOUT=20
CONFIG_MB_TIMER_PORT_ENABLED=y
CONFIG_MB_TIMER_GROUP=0
CONFIG_MB_TIMER_INDEX=0
# CONFIG_SUPPORT_STATIC_ALLOCATION is not set
CONFIG_TIMER_TASK_PRIORITY=1
CONFIG_TIMER_TASK_STACK_DEPTH=2048
CONFIG_TIMER_QUEUE_LENGTH=10
# CONFIG_L2_TO_L3_COPY is not set
# CONFIG_USE_ONLY_LWIP_SELECT is not set
CONFIG_ESP_GRATUITOUS_ARP=y
CONFIG_GARP_TMR_INTERVAL=60
CONFIG_TCPIP_RECVMBOX_SIZE=32
CONFIG_TCP_MAXRTX=12
CONFIG_TCP_SYNMAXRTX=12
CONFIG_TCP_MSS=1440
CONFIG_TCP_MSL=60000
CONFIG_TCP_SND_BUF_DEFAULT=5744
CONFIG_TCP_WND_DEFAULT=5744
CONFIG_TCP_RECVMBOX_SIZE=6
CONFIG_TCP_QUEUE_OOSEQ=y
# CONFIG_ESP_TCP_KEEP_CONNECTION_WHEN_IP_CHANGES is not set
CONFIG_TCP_OVERSIZE_MSS=y
# CONFIG_TCP_OVERSIZE_QUARTER_MSS is not set
# CONFIG_TCP_OVERSIZE_DISABLE is not set
CONFIG_UDP_RECVMBOX_SIZE=6
CONFIG_TCPIP_TASK_STACK_SIZE=3072
CONFIG_TCPIP_TASK_AFFINITY_NO_AFFINITY=y
# CONFIG_TCPIP_TASK_AFFINITY_CPU0 is not set
# CONFIG_TCPIP_TASK_AFFINITY_CPU1 is not set
CONFIG_TCPIP_TASK_AFFINITY=0x7FFFFFFF
# CONFIG_PPP_SUPPORT is not set
CONFIG_ESP32_PTHREAD_TASK_PRIO_DEFAULT=5
CONFIG_ESP32_PTHREAD_TASK_STACK_SIZE_DEFAULT=3072
CONFIG_ESP32_PTHREAD_STACK_MIN=768
CONFIG_ESP32_DEFAULT_PTHREAD_CORE_NO_AFFINITY=y
# CONFIG_ESP32_DEFAULT_PTHREAD_CORE_0 is not set
# CONFIG_ESP32_DEFAULT_PTHREAD_CORE_1 is not set
CONFIG_ESP32_PTHREAD_TASK_CORE_DEFAULT=-1
CONFIG_ESP32_PTHREAD_TASK_NAME_DEFAULT="pthread"
CONFIG_SPI_FLASH_WRITING_DANGEROUS_REGIONS_ABORTS=y
# CONFIG_SPI_FLASH_WRITING_DANGEROUS_REGIONS_FAILS is not set
# CONFIG_SPI_FLASH_WRITING_DANGEROUS_REGIONS_ALLOWED is not set
CONFIG_IP_LOST_TIMER_INTERVAL=120
CONFIG_SUPPRESS_SELECT_DEBUG_OUTPUT=y
CONFIG_SUPPORT_TERMIOS=y
# End of deprecated options
@mantriyogesh any update on your side? Just to recap:
- Disabling the asserts in the ESP-Hosted build would allow me to bypass the size check if you are able to publish a new build
- Was there anything odd with the response from the SPI Flash that did not match the datasheet or JEDEC specifications? I can report this to the chip manufacturer if so.
- Otherwise, is there anything that should change on the ESP-IDF side with respect to the flash check? It would seem that a custom driver might be a decent option with just overriding the SPI flash size check and probe. If that was the case, how soon could we get this integrated into a new build of the ESP-Hosted firmware?
Please let me know if there's anything that needs to happen on my side.
Hello @wildbiotiger ,
Sorry for the late response. I have asked the ESP-IDF team, if such changes could be published. They might take some time to respond.
In case of urgency, please use the ESP-IDF issue tracker.
Is this custom hardware? If yes, what is flash part used on the device?
Can you flash 'hello world' example without any changes in menuconfig and get us output?
@mantriyogesh it is on a custom board. I linked the datasheet for the SPI flash we are using in the first post: https://www.mouser.com/datasheet/2/698/adet_s_a0010543939_1-2956529.pdf I’ll have to run the hello world tomorrow.
Actually, you can use esp-idf with all your own expected changes, using ESP-Hosted-FG, as the firmware code is available to you and you can do any changes you need in ESP-IDF.
I understand you are running into external flash issues, but getting these up & working is kind of expected before using ESP-Hosted.
Instead of using direct binaries, you can build them in directory https://github.com/espressif/esp-hosted/tree/ESP-Hosted_MCU_Host/esp/esp_driver/network_adapter.
- setup IDF, https://github.com/espressif/esp-hosted/blob/ESP-Hosted_MCU_Host/docs/Linux_based_host/Linux_based_readme.md#22-esp-idf-setup -> Change what you need here in IDF
- Clone ESP-Hosted, https://github.com/espressif/esp-hosted/blob/ESP-Hosted_MCU_Host/docs/Linux_based_host/Linux_based_readme.md#23-esp-hosted-code-repository
- build & flash the ESP, https://github.com/espressif/esp-hosted/blob/ESP-Hosted_MCU_Host/docs/Linux_based_host/SPI_setup.md#222-source-compilation
Anyway, I have flagged the flash issue to internal SPI flash team, it might take some time to get response.
@mantriyogesh yes, that's what we were doing, and that was build of the MCU firmware was what we were using when I posted the logs originally. We have made the changes there, but we are very interested in getting a version that works with the native Linux Wi-Fi utilities (which is the version that is closed source at the moment).
Understood. I can make the changes and give you. I suppose that's the only change you are looking for. If not, can you please send the IDF patch and base commit you are using?
Hello @wildbiotiger ,
As I get input from the SPI flash team,
For this flash, its problem is that, its ID format is not recognized,
and the ID is where the size is usually get from.
What I see is that the flash driver used by the app is not compatible with it in the get_size.
Customer need to customize their driver for this point, see:
https://gitlab.espressif.cn:6688/espressif/esp-idf/-/blob/master/examples/storage/custom_flash_driver/components/custom_chip_driver/spi_flash_chip_eon.c
But TBH, This flash will have a lot of places that are not compatible with the default flash driver.
Considering the above context, is there any plan B for the SPI flash you can use? As I understand, you might end up in a lot of changes to make it supported. In case this is expected for mass production, you can get in touch with our business team, where they would fasten the support to this problem.
BTW, It is tricky to remember the names, so just explaining the variant/flavours ESP-Hosted supports.
- FG i.e. first generation
- can be used with
LinuxandMCU. It has custom control path APIs, you can use.
- can be used with
- NG i.e. next generation
- Specially designed to use Wi-Fi with wpa_supplicant (seam-less Wi-Fi control). Works only with Linux.
Now, In case you want to continue ahead, you have complete source code in above links I had shared previously for FG. You can make the changes in ESP-IDF and get the flashing working on FG first. Then let me know the changes in a patch with base commit of ESP-IDF. I will apply that patch to IDF and get you NG binary.
Hope this helps.
Thanks @mantriyogesh, we will take a look and get back to you on the implementation.
@mantriyogesh I've updated a fork of ESP-ID with the AT25 driver here: https://github.com/espressif/esp-idf/pull/9842. Would you please publish a build with this code? Other notes on the driver bringup:
- The driver should support all of the AT25SF family, so other chips will be recognized
- The original size calculation in the generic driver LOOKS like it will never report any size over 255, as when it gets divided by 1024 in the upper level driver, it will = 0. Seems like a bug in the generic driver as well
I also found another strange issue somewhat unrelated:
- ESP-IDF version 4.4
- ESP-HOSTED-FG version 0.4
- Enable Log Level Verbose
- SDIO aborts due to recursive mutex in logging function
Backtrace dump from GDB:
Reading symbols from build/network_adapter.elf...
(gdb) list *0x40083373
0x40083373 is in lock_acquire_generic (esp32/esp-idf/components/newlib/locks.c:139).
134 }
135 BaseType_t success;
136 if (!xPortCanYield()) {
137 /* In ISR Context */
138 if (mutex_type == queueQUEUE_TYPE_RECURSIVE_MUTEX) {
139 abort(); /* recursive mutexes make no sense in ISR context */
140 }
141 BaseType_t higher_task_woken = false;
142 success = xSemaphoreTakeFromISR(h, &higher_task_woken);
143 if (!success && delay > 0) {
(gdb) list *0x40081d1a
0x40081d1a is in panic_abort (esp32/esp-idf/components/esp_system/panic.c:402).
397 esp_apptrace_flush_nolock(ESP_APPTRACE_DEST_TRAX, CONFIG_APPTRACE_POSTMORTEM_FLUSH_THRESH,
398 APPTRACE_ONPANIC_HOST_FLUSH_TMO);
399 #endif
400 #endif
401
402 *((volatile int *) 0) = 0; // NOLINT(clang-analyzer-core.NullDereference) should be an invalid operation on targets
403 while (1);
404 }
405
406 /* Weak versions of reset reason hint functions.
(gdb) list *0x40090de1
0x40090de1 is in esp_system_abort (esp32/esp-idf/components/esp_system/esp_system.c:128).
123 return IDF_VER;
124 }
125
126 void __attribute__((noreturn)) esp_system_abort(const char *details)
127 {
128 panic_abort(details);
129 }
(gdb) list *0x4009804a
0x4009804a is in abort (esp32/esp-idf/components/newlib/abort.c:46).
41
42 for (size_t i = 0; i < sizeof(str) / sizeof(str[0]); i++) {
43 strcat(dest, str[i]);
44 }
45
46 esp_system_abort(buf);
47 }
(gdb) 0x40083373
Undefined command: "0x40083373". Try "help".
(gdb) list *0x40083373
0x40083373 is in lock_acquire_generic (esp32/esp-idf/components/newlib/locks.c:139).
134 }
135 BaseType_t success;
136 if (!xPortCanYield()) {
137 /* In ISR Context */
138 if (mutex_type == queueQUEUE_TYPE_RECURSIVE_MUTEX) {
139 abort(); /* recursive mutexes make no sense in ISR context */
140 }
141 BaseType_t higher_task_woken = false;
142 success = xSemaphoreTakeFromISR(h, &higher_task_woken);
143 if (!success && delay > 0) {
(gdb) list *0x400834bd
0x400834bd is in _lock_acquire_recursive (esp32/esp-idf/components/newlib/locks.c:167).
162 void IRAM_ATTR _lock_acquire(_lock_t *lock) {
163 lock_acquire_generic(lock, portMAX_DELAY, queueQUEUE_TYPE_MUTEX);
164 }
165
166 void IRAM_ATTR _lock_acquire_recursive(_lock_t *lock) {
167 lock_acquire_generic(lock, portMAX_DELAY, queueQUEUE_TYPE_RECURSIVE_MUTEX);
168 }
169
170 int IRAM_ATTR _lock_try_acquire(_lock_t *lock) {
171 return lock_acquire_generic(lock, 0, queueQUEUE_TYPE_MUTEX);
(gdb) list *0x40083536
0x40083536 is in __retarget_lock_acquire_recursive (esp32/esp-idf/components/newlib/locks.c:323).
318
319 void IRAM_ATTR __retarget_lock_acquire_recursive(_LOCK_T lock)
320 {
321 check_lock_nonzero(lock);
322 MAYBE_OVERRIDE_LOCK(lock, &s_common_recursive_mutex);
323 _lock_acquire_recursive(&lock);
324 }
325
326 int IRAM_ATTR __retarget_lock_try_acquire(_LOCK_T lock)
327 {
(gdb) list *0x4015370e
0x4015370e is in _vfprintf_r (/builds/idf/crosstool-NG/.build/xtensa-esp32-elf/src/newlib/newlib/libc/stdio/vfprintf.c:853).
848 /builds/idf/crosstool-NG/.build/xtensa-esp32-elf/src/newlib/newlib/libc/stdio/vfprintf.c: No such file or directory.
(gdb) list *0x40156741
0x40156741 is in vprintf (/builds/idf/crosstool-NG/.build/xtensa-esp32-elf/src/newlib/newlib/libc/stdio/vprintf.c:34).
29 /builds/idf/crosstool-NG/.build/xtensa-esp32-elf/src/newlib/newlib/libc/stdio/vprintf.c: No such file or directory.
(gdb) list *0x4016466d
0x4016466d is in esp_log_writev (esp32/esp-idf/components/log/log.c:200).
195 esp_log_level_t level_for_tag = s_log_level_get_and_unlock(tag);
196 if (!should_output(level, level_for_tag)) {
197 return;
198 }
199
200 (*s_log_print_func)(format, args);
201
202 }
203
204 void esp_log_write(esp_log_level_t level,
(gdb) list *0x40096add
0x40096add is in esp_log_write (esp32/esp-idf/components/log/log.c:210).
205 const char *tag,
206 const char *format, ...)
207 {
208 va_list list;
209 va_start(list, format);
210 esp_log_writev(level, tag, format, list);
211 va_end(list);
212 }
213
214 static inline bool get_cached_log_level(const char *tag, esp_log_level_t *level)
(gdb) list *0x400fb4e1
0x400fb4e1 is in sdio_slave_hal_load_buf (esp32/esp-idf/components/hal/sdio_slave_hal.c:667).
662
663 if (tail == NULL) {
664 //no one in the ll, start new ll operation.
665 sdio_slave_ll_recv_start(hal->slc, desc);
666 sdio_slave_ll_recv_intr_ena(hal->slc, true);
667 HAL_LOGV(TAG, "recv_load_buf: start new");
668 } else {
669 //restart former ll operation
670 sdio_slave_ll_recv_restart(hal->slc);
671 HAL_LOGV(TAG, "recv_load_buf: restart");
(gdb) q
Hey @mantriyogesh, any chance on getting the pull request integrated and publishing a new build?
Sorry for the delayed response.
- Can you please provide
IDF branch usedandgit commit, over which you need the MR/patch to be applied? - For the recent issue of logging, you can raise the issue in ESP-IDF.
- Quick suggestions:
- Disable that log
- In case want to retain the log, try with, https://docs.espressif.com/projects/esp-idf/en/latest/esp32/api-reference/system/log.html#c.ESP_EARLY_LOGI
For ESP-Hosted-NG, we are right now limited with IDF branch release/4.4, git commit, 6d85d53c. If you have time, you can give me a patch over the same commit. Otherwise, I will have to port and then get you the ESP binary (might take a day or two , as I am on some other issue)
Also, I see from prior logs, you are using ESP32 with SDIO transport option. Considering ESP binary creation, would that transport be sufficient for you?
@mantriyogesh, I had put that in my last post. Here’s the pull request: https://github.com/espressif/esp-idf/pull/9842 And the commit eec8e298d979cd743cff80ebc5495e26ef624406
and yes, SDIO transport should be fine. I think the patch I created with the pull request uses v4.4. If it doesn’t just let me know.
@mantriyogesh I've added a new pull request targeting just v4.4 here:
https://github.com/espressif/esp-idf/pull/9884
Let me know if you need anything else.
Hello Nicholas,
Apologies for delay. I hope this would be useful for you.
GH_161_29sep22.tgz is only ESP firmware with your code over ESP-IDF release/v4.4 6d85d53c
The supported commit at Host is f1d32ab
Please note,
- This is not tested build. Just compiled.
- You might face issues if you use different host code other than above commit
- ESP side code is also going to be published in upcoming releases. At that point, you can even sync to master at both side, ESP & Host.
@mantriyogesh, haven't gotten a chance to test it yet. Work stuff cropping up.