z03mmc
z03mmc copied to clipboard
devbis
LYWSD03MMC B1.4 bricked
Just bricked 2pcs of LYWSD03MMC Hardware Version: LYWSD03MMC B1.4, Software Version: 9.9, Sensor: SHTC3 (SHTV3)
I'm doing flashing as described in readme:
- ATC_ota_400000
- reconnect with new name
- z03mmc.bin
But after flashing target firmware device stucks on values and not connecting to zigbee. Reinserting battery causes showing initial values, then screen blinks and stucks again (not updating values and not connecting to zigbee)
I did not got a new name after flashing with ATC_ota_40000.bin and replacing the battery afterwards (for minutes). I used the parameters from token_extractor to be able to Login. Do Activation did not work - wait for 10 minutes and nothing happend (maybe timeout)
13:12:22: Searching for devices 13:13:25: Connecting to: LYWSD03MMC 13:13:32: Hardware Revision String: B1.4 13:13:32: Software Revision String: 0159 13:13:32: Firmware Revision String: 2.1.1_0159 13:13:32: Detected Mi device 13:13:32: Connected 13:14:00: Send Login, please wait... 13:14:01: Received device infos are correct 13:14:01: Login successfull 13:14:08: File: ATC_ota_40000.bin 13:14:08: File size: 82516 bytes 13:14:08: Count: 5158 13:14:10: Start DFU 13:15:56: Update done after 104.879 seconds 13:16:03: Disconnected.
So flashing with z03mmc.bin failed at the end
14:40:56: Searching for devices
14:41:11: Connecting to: LYWSD03MMC
14:41:18: Hardware Revision String: B1.4
14:41:18: Software Revision String: 0159
14:41:18: Firmware Revision String: 2.1.1_0159
14:41:18: Detected Mi device
14:41:18: Connected
14:41:32: Send Login, please wait...
14:41:32: Received device infos are correct
14:41:32: Login successfull
14:41:39: Start DFU
-> stopped here
14:44:01: Update error: NotSupportedError: GATT operation failed for unknown reason.
14:44:01: Disconnected.
Tried at different device (mobile phone), too.
Any ideas?
Try to replace batteries with new ones.
Just replaced battery and it works. Very strange thing, maybe add this to docs?
Try to replace batteries with new ones.
Just replaced battery and it works. Very strange thing, maybe add this to docs?
Perhaps zigbee firmware is more sensitive to battery level.
Try to replace batteries with new ones.
Just replaced battery and it works. Very strange thing, maybe add this to docs?
Perhaps zigbee firmware is more sensitive to battery level.
I flashed third sensor with https://pvvx.github.io/ATC_MiThermometer/TelinkMiFlasher.html with same battery (after flashing previous two) and it connected after flashing without problems.
First bricked sensor was thrown away (i tried to flash it via UART and completely bricked it), second was connected after battery replacement with 100% capacity.
What is the difference between these two firmwares?
I flashed third sensor with https://pvvx.github.io/ATC_MiThermometer/TelinkMiFlasher.html with same battery (after flashing previous two) and it connected after flashing without problems.
Tried without success obviously due to the version
11:05:39: Searching for devices 11:06:20: Connecting to: LYWSD03MMC 11:06:32: Hardware Revision String: B1.4 11:06:32: Software Revision String: 0159 11:06:32: Firmware Revision String: 2.1.1_0159 11:06:32: Detected Mi device 11:06:32: (!) Version: 2.1.1_0159 is temporarily not supported (!) 11:06:32: Disconnected.