Problem setting up second Visonic Panel

[robermf]

Hello! I am having this issue in a fresh Instalation of HaOS. I was using (with previous versions) in a supervised HA instance running on Debian.

I have a Powermax Pro and Powermaster 10. When I add the first panel all is ok, but when I add the second panel I only it is in Powerlink mode and everything looks fine but Home Assistant only can get the first sensor (I tried changing the order of adding panels, older versions of the add-on...)

I attach the log (I tried to clean it up a little bit) and read but I don't understad very much. In the log appears a error setting up the sensors:

home-assistant-2.log

And here is the info of the panel 2:

code_format: null changed_by: None code_arm_required: false Panel Mode: Powerlink Protocol Version: 1.0.20.0 Watchdog Timeout (Total): 0 Watchdog Timeout (Past 24 Hours): 0 Download Timeout: 0 Download Retries: 0 Panel Problem Count: 0 Panel Problem Time: "" Panel Last Event: None Panel Last Event Data: Zone: 0 Entity: null Tamper: false Siren: false Reset: false Time: "2020-01-01T00:00:00.0" Count: 0 Type: [] Event: [] Mode: [] Name: [] Panel Alarm Status: None Panel Trouble Status: None Panel Siren Active: false Panel Status: Disarmed Panel Status Code: Disarmed Panel Ready: "Yes" Panel Alert In Memory: "No" Panel Trouble: "Yes" Panel Bypass: "No" Panel Status Changed: "No" Panel Alarm Event: "No" Panel Armed: "No" Power Master: "Yes" Panel Model: PowerMaster 10 Panel Type: 7 Model Type: 104 Panel Name: Unknown EPROM Change Time I Think: Not Set Jamming Detection: Disable Entry Delay 1: 30 Seconds Entry Delay 2: 1 Minute Exit Delay: 30 Seconds Bell Time: 4 Minutes Piezo Beeps: Enable Swinger Stop: After 1 Time Aux Key 1: Instant Arm Aux Key 2: Cancel Exit Delay Supevision Interval: 12 Hours No Activity Time: Disable Alarm Cancel Time: 5 Minutes Abort Time: 30 Seconds Confirm Alarm Timer: 60 Minutes Screen Saver: "Off" Reset Option: User Reset Duress: "2580" AC Failure Report: 5 Minutes User Permit: Disable Zone Restore: Report Restore Tamper Option: "On" PGM By Line Fail: "No" Auto Arm Option: Disable Send 2wv Code: Don't Send Memory Prompt: Disable Time Format: Europe - 24H Date Format: Europe DD/MM/YYYY Low Battery Acknowledge: "Off" Not Ready: Normal X10 Flash On Alarm: No Flash Disarm Option: Any Time Siren On Line: Disable on Fail Upload Option: Any Time Panic Alarm: Audible Panic Exit Mode: Normal Bell Report Option: Others Internal/Strobe Siren: Internal Siren Quick Arm: "Off" Back Light Time: Off After 10 Seconds Two-Way Voice - Private: Disable Latchkey Arming: "Off" Bypass: No Bypass Trouble Beeps: Disable Cross Zoning: "Off" Recent Close Report: "Off" Piezo Siren: "On" Dialing Method: Tone (DTMF) Remote Access: "On" Report Confirmed Alarm: Disable Report 1st Account No: "001234" 2nd Account No: "005678" Ringback Time: 1 Minute Report to Central Station: All but Open/Close * Backup Report To Pager: Disable Report Reporting To Private Tel: Disable Report Central Station Dialing Attempts: "8" Report Format: SIA 4/2 Pulse Rate: 20 pps Two-Way Voice To Central Stations: Disable Autotest Time: "12:00" Autotest Cycle: Disable Line Failure Report: Don't Report System Inactive Report: Disable Ambient Level: Low Level PowerLink Failure: Disable Report GSM Line Purpose: SMS Only GSM Report to SMS: Disable Report GSM Line Failure: Don't Report GSM Install: Not Installed GSM Select Antenna: Internal antenna X10 Lockout Time (start HH:MM): "07:00" X10 House Code: B PGM By Arm Away: Disable PGM By Arm Home: Disable PGM By Disarm: Disable PGM By Delay: Disable PGM By Memory: Disable PGM By Keyfob: Disable PGM Act Zone A: Disable PGM Act Zone B: Disable PGM Act Zone C: Disable PGM Pulse Time: 2 Seconds X10 Trouble Indication: Disable X10 3 Phase and frequency: Disable X10 Report on Fail to Central Station 1: Disable X10 Report on Fail to Central Station 2: Disable X10 Report on Fail to Pager: Disable X10 Report on Fail to Private: Disable X10 Report on Fail to SMS: Disable Set Voice Option: Enable Voice Squawk Option: Low Level Auto Arm Time: "12:00" Panel Eprom: J-703069 I18.415 Panel Software: JS702947 I18.415 Panel Serial: "0907030000." Door Zones: "" Motion Zones: "" Smoke Zones: "" Ignored Zones: "" Other Zones: Z01,Z02,Z03,Z04,Z05,Z06,Z07,Z08 Devices: "" Client Version: 0.8.5.2 Exception Count: 0 panel: 2 friendly_name: Visonic Alarm Panel 2 supported_features: 7

Thank you for your help, Dave.