firmware please help

[freddygino]

hi im trying to load the firmware on the launch pad followed the video to debug all went well till i hit the spider button i get load program error ...please help not to familiar to programming so this is all new to me

here is a pic of the error

tia

[kwackers]

I'm not an expert on the TI board but it looks like the first error I can see in that list is your problem - "but flash is not available on this device". The errors after this are simply because the later steps will automatically fail if it couldn't flash the device.

I guess the first question would be - do you have the right board? (Some variations may not have flash) Then are there any jumpers/switches that might disable the flash that you might have accidentally tweaked?

I don't have my board in front of me, it's all packaged up on my lathe now so I can't do much other than give you the above suggestions - sorry.

[freddygino]

Hi and thank you for answering.... Yea i checked the board followed James video step by step installed the same version ccs software as he and still get that error... Hopefully someone ran into the same problem and fixed it and would post it.... Thanks again

[Chucksbp]

I have seen other people having a problem that totally removed code composer from their computer, then reinstalled code composer and re configured everything. It may be worth a try?? also i would go through the three switches and flick them back and fort a few times. the plastic tape they use can be very finicky and stop the switch movement. Again I am no expert and i found this to be the most troubling part of the build. i can only say the end is well worth the trouble, you will love the ELS!

[freddygino]

I tried about 6 different versions of ccs and all came back with the same error... I didn't try flicking the switches I'll try that... I did email support at Texas instruments and the have a section about that but I don't know what I'm reading cause I don't know coding lol

[Chucksbp]

Are you using a version 9 of code composer? I know the latest versions will not work with Clough 42 software! Sent from my Galaxy -------- Original message --------From: freddygino @.> Date: 5/13/23 10:44 AM (GMT-05:00) To: clough42/electronic-leadscrew @.> Cc: Chucksbp @.>, Comment @.> Subject: Re: [clough42/electronic-leadscrew] firmware please help (Issue #260) I tried about 6 different versions of ccs and all came back with the same error... I didn't try flicking the switches I'll try that... I did email support at Texas instruments and the have a section about that but I don't know what I'm reading cause I don't know coding lol

—Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you commented.Message ID: @.***>

[freddygino]

Yes I'm using the same version as James v9. 1

[Chucksbp]

i had good luck with version 9.3.0

[freddygino]

Tried that 1

[freddygino]

this is what texas instruments sent me to resolve my issue...i really dont know what im reading ...if anyone would be so kind and checking out this link and help me with this i will greatly appreciate it ....thank you

https://e2e.ti.com/support/tools/code-composer-studio-group/ccs/f/code-composer-studio-forum/738865/faq-ccs-why-am-i-getting-a-data-verification-error-when-i-load-my-program

[Chucksbp]

Can you post a picture of your Configuration H page? are there any errors showing in the box on the very bottom right of the page?

[freddygino]

i installed ccs v9.3 and this is the error i get

[freddygino]

this is the config h

[Chucksbp]

Try this, remove the Clough42 board from the TI launch board. re install the three jumpers. use the supplied USB cable that came with the Launch board and see if you can program the chip. Thats how i did both of my boards. then i reinstalled the Clough42 board and connected everything. , i had issues with my first encoder and it wiped out encoder input one so i reprogramed the board several times successfully and then reprogramed a second board for a backup.

[freddygino]

ok will try thanks

[freddygino]

same error

[Chucksbp]

i have no idea what is happening. Hopefully James will look at this and respond. he often does. I wish i could help more.

[freddygino]

oh i so appreciate you try helping me thank you ,,,

[Chucksbp]

you are welcome!!!

[tomvikse]

Try a different computer..

[freddygino]

Yea that's what I'm doing next thanks

[freddygino]

tried different computer same thing....could there be something wrong with the file? i downloaded on 2nd computer from github

[Chucksbp]

Are you trying to flash the chip from this view?? this is where you should be doing the flash from. , show me this view let me see if there are any errors in the bottom right.

[freddygino]

hi chuck yesterday i was looking at the board and noticed f280025c its the wrong board i checked my invoice and it says f280049c so i spoke with someone from mouser electronics the place i bought the board they are sending me the board tommorow...i apoligize hope its the right 1 tommorow

[freddygino]

[Chucksbp]

No need to apologies for anything!!!! that's totally wild! who would have ever thought. At a glance it looks like the correct board. I hope this solves your problem, let us know if you get it working. best of luck to the finish!!!! I hope this fixes your issues!!!

[freddygino]

thank you so much and definitly will let you know

[kwackers]

I suspected that would be the case - hence my initial response... ;-) Live and learn.

[freddygino]

I suspected that would be the case - hence my initial response... ;-) Live and learn.

Yes that was you first question I overlooked... Thank you

[freddygino]

up and running in 3 minutes thanks guys

[Chucksbp]

That's great!! Congratulations!!!!