I'm bought Els Pc Board, Encoder, Els Control panel, it's time for the servo Kit...

[andrea271068]

I as I wrote in the objective, it's time for me to buy the servo Kit, servo+driver+ power supply, I don't have 3 phase, is so important? I can't use my domestic 220V? I live in Italy it's normal for us 220V.

I can't find even in e-bay your servo and the Kl -5080H

I have a Chinese mini-lathe, w

I can buy those kind of servo?

Nema23 2N.m 57 Hybrid Closed Loop Servo Stepper Motor 2Nm 76mm+HSS57 Servo Driver Controller CNC Kit 24-50V DC For CNC Router Engraving Milling Machine

many thanks in advance

[Hobby-Lofty]

Andrea, I fitted to my 7x14 mini lathe: eBay kit: 3Nm Nema 24 Closed Loop Stepper Hybrid Servo Motor 5A 86mm &Driver CL57Y CNC Kit it works fine Power supply from banggood : AC 110/220V to DC 0-60V 8A 480W Adjustable Regulated Switch Power Supply Driver Transformer W/ LCD Display for LED Strips, I've been running it at 30v . In the UK we have 240v and it works fine The nema 24 just has 10mm diameter shaft. this may be overkill but I know it works for me. Good luck Lofty

[forrestlw]

Andrea, The power supply does not require 3 phase to operate. Just 115v or 220v single phase house voltage. The phase is the type of motor/drive set you are using. A 3 phase set has a 1.2 degree step angle. A 2 phase has a 1.8 degree step angle. Most nema 23 motors have a 8mm shaft and very few have a .250" (6.35mm) shaft. Andrea, did this answer your question?

[andrea271068]

Dear Lofty, many thanks, really, I was confused in what to buy.

In case of problem I can write you again?

Andrea Pisani Export Manager

Composad srl – Italy Mobile Phone: 0039 335 70 98 102 E-mail: [email protected]mailto:[email protected]

From: Hobby-Lofty [email protected] Sent: Friday, December 18, 2020 2:48 PM To: clough42/electronic-leadscrew [email protected] Cc: Andrea Pisani [email protected]; Author [email protected] Subject: Re: [clough42/electronic-leadscrew] I'm bought Els Pc Board, Encoder, Els Control panel, it's time for the servo Kit... (#116)

Andrea, I fitted to my 7x14 mini lathe: eBay kit: 3Nm Nema 24 Closed Loop Stepper Hybrid Servo Motor 5A 86mm &Driver CL57Y CNC Kit it works fine Power supply from banggood : AC 110/220V to DC 0-60V 8A 480W Adjustable Regulated Switch Power Supply Driver Transformer W/ LCD Display for LED Strips, I've been running it at 30v . In the UK we have 240v and it works fine The nema 24 just has 10mm diameter shaft. this may be overkill but I know it works for me. Good luck Lofty

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHubhttps://github.com/clough42/electronic-leadscrew/issues/116#issuecomment-748093157, or unsubscribehttps://github.com/notifications/unsubscribe-auth/ASB5PO72Y2UDWEJRKVV3EJLSVNMRRANCNFSM4U7TTJUQ.

[andrea271068]

Hi, finally I bought a servo Kit, I follow your suggestion but come with 350W power supply 36 V, I hope is good. I never do electronic configuration or job, is my first time, hope that I can do it, is a challenge . may I will need your help guys to go true to this adventure. Especially for the setup and configuration.

Thanks for everithing.