Pin issue

[dunbard0401]

I've prepped an OS image for my Manta M8P w/ CB1 (no eMMC), added the "generic-bigtreetech-manta-m8p-V2_0.cfg" config file, and i get this error on startup:

[dunbard0401]

this is the config file:

This file contains common pin mappings for the BIGTREETECH Manta M8P V2.0

To use this config, the firmware should be compiled for the

STM32H723 with a "128KiB bootloader" "25 MHz crystal"

and "USB (on PA11/PA12)", "CAN bus (on PD0/PD1)" or Serial (on USART1 PA10/PA9).

See docs/Config_Reference.md for a description of parameters.

Motor1

[stepper_x] step_pin: PE6 dir_pin: PE5 enable_pin: !PC14 microsteps: 16 rotation_distance: 40 endstop_pin: ^PF4 position_endstop: 0 position_max: 235 homing_speed: 50

Motor2

[stepper_y] step_pin: PE2 dir_pin: PE1 enable_pin: !PE4 microsteps: 16 rotation_distance: 40 endstop_pin: ^PF3 position_endstop: 0 position_max: 235 homing_speed: 50

Motor3

[stepper_z] step_pin: PB8 dir_pin: !PB7 enable_pin: !PE0 microsteps: 16 rotation_distance: 8 endstop_pin: ^PF2 position_endstop: 0 position_max: 270 position_min: -5.0 homing_speed: 8 second_homing_speed: 3 homing_retract_dist: 3

Motor4

The M8P only has 4 heater outputs which leaves an extra stepper

This can be used for a second Z stepper, dual_carriage, extruder co-stepper,

or other accesory such as an MMU

#[stepper_] #step_pin: PB4 #dir_pin: PB3 #enable_pin: !PB6 #endstop_pin: ^PF1 #...

Motor5

[extruder] step_pin: PG13 dir_pin: PG12 enable_pin: !PG15 microsteps: 16 rotation_distance: 33.500 nozzle_diameter: 0.4 filament_diameter: 1.75 heater_pin: PA0 # HE0 sensor_pin: PB0 # T0 sensor_type: Generic 3950 control: pid pid_Kp: 22.2 pid_Ki: 1.08 pid_Kd: 114 min_temp: 0 max_temp: 250

End-Stop 5

#[filament_switch_sensor material_0] #switch_pin: PF0

Motor6

#[extruder1] #step_pin: PG9 #dir_pin: PD7 #enable_pin: !PG11 #heater_pin: PA1 # HE1 #sensor_pin: PC5 # T1 #...

End-Stop 6

#[filament_switch_sensor material_1] #switch_pin: PC15

Motor7

#[extruder2] #step_pin: PD4 #dir_pin: PD3 #enable_pin: !PD6 #heater_pin: PA3 # HE2 #sensor_pin: PC4 # T2 #...

Motor8

#[extruder3] #step_pin: PC7 #dir_pin: PC8 #enable_pin: !PD2 #heater_pin: PA5 # HE3 #sensor_pin: PA7 # T3 #...

[heater_bed] heater_pin: PF5 sensor_pin: PB1 # TB sensor_type: ATC Semitec 104GT-2 control: watermark min_temp: 0 max_temp: 130

#[fan_generic soc-fan] #pin: host:gpio79 #CB1 #pin: host:gpio26 #CM4

Fan0

[fan] pin: PF7

Fan1

#[heater_fan fan1] #pin: PF9

Fan2

#[heater_fan fan2] #pin: PF6

Fan3

#[heater_fan fan3] #pin: PA8

Fan4

#[heater_fan fan4] #pin: PA4

Fan5

#[heater_fan fan5] #pin: PA6 #tachometer_pin: PC2

Fan6

#[heater_fan fan6] #pin: PA2 #tachometer_pin: PC1

[mcu]

serial: /dev/serial/by-id/usb-Klipper_stm32g0b1xx_0E00290009504B4633373520-if00

[printer] kinematics: cartesian max_velocity: 300 max_accel: 3000 max_z_velocity: 5 max_z_accel: 100

########################################

TMC2209 configuration

########################################

Motor1

#[tmc2209 stepper_x] #uart_pin: PC13 ##diag_pin: PF4 #run_current: 0.800 #stealthchop_threshold: 999999

Motor2

#[tmc2209 stepper_y] #uart_pin: PE3 ##diag_pin: PF3 #run_current: 0.800 #stealthchop_threshold: 999999

Motor3

#[tmc2209 stepper_z] #uart_pin: PB9 ##diag_pin: PF2 #run_current: 0.650 #stealthchop_threshold: 999999

Motor4

#[tmc2209 stepper_] #uart_pin: PB5 ##diag_pin: PF1 #run_current: 0.650 #stealthchop_threshold: 999999

Motor5

#[tmc2209 extruder] #uart_pin: PG14 #run_current: 0.800 #stealthchop_threshold: 999999

Motor6

#[tmc2209 extruder1] #uart_pin: PG10 #run_current: 0.800 #stealthchop_threshold: 999999

Motor7

#[tmc2209 extruder2] #uart_pin: PD5 #run_current: 0.800 #stealthchop_threshold: 999999

Motor8

#[tmc2209 extruder3] #uart_pin: PC6 #run_current: 0.800 #stealthchop_threshold: 999999

########################################

TMC2130 configuration

########################################

Motor1

#[tmc2130 stepper_x] #cs_pin: PC13 #spi_software_mosi_pin: PG6 #spi_software_miso_pin: PG7 #spi_software_sclk_pin: PG8 ##diag1_pin: PF4 #run_current: 0.800 #stealthchop_threshold: 999999

Motor2

#[tmc2130 stepper_y] #cs_pin: PE3 #spi_software_mosi_pin: PG6 #spi_software_miso_pin: PG7 #spi_software_sclk_pin: PG8 ##diag1_pin: PF3 #run_current: 0.800 #stealthchop_threshold: 999999

Motor3

#[tmc2130 stepper_z] #cs_pin: PB9 #spi_software_mosi_pin: PG6 #spi_software_miso_pin: PG7 #spi_software_sclk_pin: PG8 ##diag1_pin: PF2 #run_current: 0.650 #stealthchop_threshold: 999999

Motor4

#[tmc2130 stepper_] #cs_pin: PB5 #spi_software_mosi_pin: PG6 #spi_software_miso_pin: PG7 #spi_software_sclk_pin: PG8 ##diag1_pin: PF1 #run_current: 0.800 #stealthchop_threshold: 999999

Motor5

#[tmc2130 extruder] #cs_pin: PG14 #spi_software_mosi_pin: PG6 #spi_software_miso_pin: PG7 #spi_software_sclk_pin: PG8 #run_current: 0.800 #stealthchop_threshold: 999999

Motor6

#[tmc2130 extruder1] #cs_pin: PG10 #spi_software_mosi_pin: PG6 #spi_software_miso_pin: PG7 #spi_software_sclk_pin: PG8 #run_current: 0.800 #stealthchop_threshold: 999999

Motor7

#[tmc2130 extruder2] #cs_pin: PD5 #spi_software_mosi_pin: PG6 #spi_software_miso_pin: PG7 #spi_software_sclk_pin: PG8 #run_current: 0.800 #stealthchop_threshold: 999999

Motor8

#[tmc2130 extruder3] #cs_pin: PC6 #spi_software_mosi_pin: PG6 #spi_software_miso_pin: PG7 #spi_software_sclk_pin: PG8 #run_current: 0.800 #stealthchop_threshold: 999999

[board_pins] aliases: # EXP1 header EXP1_1=PE7, EXP1_2=PG1, EXP1_3=PG0, EXP1_4=PF15, EXP1_5=PF14, EXP1_6=PF13, # Slot in the socket on this side EXP1_7=PF12, EXP1_8=PF11, EXP1_9=<GND>, EXP1_10=<5V>,

# EXP2 header
EXP2_1=PE13, EXP2_2=PE12,
EXP2_3=PE15, EXP2_4=PE11,
EXP2_5=PE10, EXP2_6=PE14,      # Slot in the socket on this side
EXP2_7=PE8, EXP2_8=<RST>,
EXP2_9=<GND>, EXP2_10=<NC>

See the sample-lcd.cfg file for definitions of common LCD displays.

#[adxl345] #cs_pin: PA15 #spi_bus: spi3a

#[bltouch] #sensor_pin: PD13 #control_pin: PD12

Proximity switch

#[probe] #pin: PD8

#[output_pin ps_on_pin] #pin: PD14

#[neopixel my_neopixel_1] #pin: PD15

#[hall_filament_width_sensor] #adc1: PC0 #adc2: PF10