BigTreeTech TFT35 & Raspberry Pi (Octoprint) not working

[BakaBazooka]

Cannot get the TFT35 touchscreen to work with octoprint using a MKS GEN L? When removing the touchscreen, octoprint works normally.

How to fix this problem

[Msq001]

maybe you use a same UART port in TFT35 and Raspberry Pi, The USB and AUX-1 use the same UART. you can click "Settings->Disconnect" on touch screen to disconnect the TFT35, or use the other UART connect with TFT35

[BakaBazooka]

I am using a bunch of 2130 x4 on SPI connections.

Is there a way to separate the USB and AUX-1 connection?? Or can anything be done in the Marlin firmware to split into 2 separate serial connections ? (one for octoprint and the other for the touch scren)

[Msq001]

yeah, marlin-bugfix-2.0.x support the second serial port. you can #define SERIAL_PORT 0 for usb, and #define SERIAL_PORT_2 2 for TFT35, wiring RX(TFT35) to TXD2(MKS Gen L), TX(TFT35) to RXD2(MKS Gen L)

[BakaBazooka]

I am already using the EXP1 & EXP2 pins for the RepRap LCD, and the AUX-2 & AUX-3 for the TMC2130 SPI connections. Is there a way to address or define the serial port to the AUX-1 on the MKS Gen L for the touchscreen?

[Msq001]

the serial port in AUX-1 was be wired with USB in PCB, so if you use Raspberry Pi by USB, Serial ports on AUX-1 are Actually unusable. atmega2560 has four hardware serial ports, two of which are used as endstops, leaving only two serial ports in AUX-1 and EXP-1 for use. I want to know why TFT35 and RepRap LCD need to be used at the same time. T_T

[BakaBazooka]

Thanks @Msq001

I am using the RepRap LCD to adjust my BLTouch settings, since the TFT35 does not come with the BLTouch commands and I do not know how to configure them. So i was hoping to get it working with the two screens. Is it possible to use the EXP-2 instead of the EXP-1, and if so what serial port should it be addressed to?

Has anyone done a step by step guide for Marlin 2.0 for Ender 3 with MKS Gen L? Can't get my firmware to compile.

[Msq001]

The pin of RepRap LCD display is on EXP-1, and the EXP-2 is for SD Card, So if you want to use EXP-2 to display RepRap LCD and EXP-1 to insert TFT35, you need to modify the pins_xx.h for MKS_GEN_L in Marlin firmware.

[BakaBazooka]

Thanks for the info. I might just order the SKR V1.3 board

I assume that the SKR v1.3 would be better for connecting both screens and octoprint? Since it has a dedicated TFT screen port. But I have a question: the TFT port sharing the same UART connection with the USB port?

[Msq001]

The USB port of SKR V1.3 uses virtual serial port. not the same UART as TFT

[MDRudnicki]

This worked for me in Configuration.h, Marlin 2.0.:

#define SERIAL_PORT 0 /**

• Select a secondary serial port on the board to use for communication with the host.
• This allows the connection of wireless adapters (for instance) to non-default port pins.
• Serial port -1 is the USB emulated serial port, if available.
• :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT_2 -1 I'm running a BTT SKR v1.3 + TFT3.5 + Octoprint and can control the printer through the touchscreen and Octoprint.

[arut16]

@MDRudnicki You just connected your RPi by USB to SKR ?

[bdelia]

@MDRudnicki , I have a similar setup except I am using the TFT24 V1.1 instead of the TFT3.5. I have the serial ports defined as you do in Marlin, but I cannot seem to get Octoprint and the TFT to operate at the same time. I am using the SKR V1.3 board...Just got the TFT24 a couple of days ago and stuggling to get it fully configured.

Would you mind sharing your Configuration.h, Configuration_adv.h, and aany files associated with PIN assignments like pins.h, pins_BTT_SKR_common.h and pins_BTT_SKR_V1_3.h? I'd like to compare and see if I have missed something with the Marlin config.

[MDRudnicki]

Yes

Sent from my iPhone

On Apr 17, 2020, at 8:03 AM, arut16 [email protected] wrote:

 @MDRudnicki You just connected your RPi by USB to SKR ?

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub, or unsubscribe.

[MDRudnicki]

Hi Brett,

Here are the files. I have not touched pins.

I found that the screen sometimes does not turn on when the printer is switched on, but will come on after turning off and on again

I hope this helps.

Note- the configuration files are configures for a BLTouch, and also have my extruder and hot end PID settings.

On Wed, Apr 29, 2020 at 3:55 PM Brett Delia [email protected] wrote:

@MDRudnicki https://github.com/MDRudnicki , I have a similar setup except I am using the TFT24 V1.1 instead of the TFT3.5. I have the serial ports defined as you do in Marlin, but I cannot seem to get Octoprint and the TFT to operate at the same time. I am using the SKR V1.3 board...Just got the TFT24 a couple of days ago and stuggling to get it fully configured.

Would you mind sharing your Configuration.h, Configuration_adv.h, and aany files associated with PIN assignments like pins.h, pins_BTT_SKR_common.h and pins_BTT_SKR_V1_3.h? I'd like to compare and see if I have missed something with the Marlin config.

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/bigtreetech/BIGTREETECH-TFT35-V1.2/issues/9#issuecomment-621459103, or unsubscribe https://github.com/notifications/unsubscribe-auth/AOFAIJLKLQRIC3FPDJCEFADRPCH55ANCNFSM4HGMZEMA .

/**

• Marlin 3D Printer Firmware
• Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
• Based on Sprinter and grbl.
• Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
• This program is free software: you can redistribute it and/or modify
• it under the terms of the GNU General Public License as published by
• the Free Software Foundation, either version 3 of the License, or
• (at your option) any later version.
• This program is distributed in the hope that it will be useful,
• but WITHOUT ANY WARRANTY; without even the implied warranty of
• MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
• GNU General Public License for more details.
• You should have received a copy of the GNU General Public License
• along with this program. If not, see http://www.gnu.org/licenses/.

*/ #pragma once

/**

• Configuration_adv.h
• Advanced settings.
• Only change these if you know exactly what you're doing.
• Some of these settings can damage your printer if improperly set!
• Basic settings can be found in Configuration.h

*/ #define CONFIGURATION_ADV_H_VERSION 020000

// @section temperature

//=========================================================================== //=============================Thermal Settings ============================ //===========================================================================

// // Custom Thermistor 1000 parameters // #if TEMP_SENSOR_0 == 1000 #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C #define HOTEND0_BETA 3950 // Beta value #endif

#if TEMP_SENSOR_1 == 1000 #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C #define HOTEND1_BETA 3950 // Beta value #endif

#if TEMP_SENSOR_2 == 1000 #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C #define HOTEND2_BETA 3950 // Beta value #endif

#if TEMP_SENSOR_3 == 1000 #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C #define HOTEND3_BETA 3950 // Beta value #endif

#if TEMP_SENSOR_4 == 1000 #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C #define HOTEND4_BETA 3950 // Beta value #endif

#if TEMP_SENSOR_5 == 1000 #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C #define HOTEND5_BETA 3950 // Beta value #endif

#if TEMP_SENSOR_6 == 1000 #define HOTEND6_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor #define HOTEND6_RESISTANCE_25C_OHMS 100000 // Resistance at 25C #define HOTEND6_BETA 3950 // Beta value #endif

#if TEMP_SENSOR_7 == 1000 #define HOTEND7_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor #define HOTEND7_RESISTANCE_25C_OHMS 100000 // Resistance at 25C #define HOTEND7_BETA 3950 // Beta value #endif

#if TEMP_SENSOR_BED == 1000 #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C #define BED_BETA 3950 // Beta value #endif

#if TEMP_SENSOR_CHAMBER == 1000 #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C #define CHAMBER_BETA 3950 // Beta value #endif

// // Hephestos 2 24V heated bed upgrade kit. // https://store.bq.com/en/heated-bed-kit-hephestos2 // //#define HEPHESTOS2_HEATED_BED_KIT #if ENABLED(HEPHESTOS2_HEATED_BED_KIT) #undef TEMP_SENSOR_BED #define TEMP_SENSOR_BED 70 #define HEATER_BED_INVERTING true #endif

/**

• Heated Chamber settings */ #if TEMP_SENSOR_CHAMBER #define CHAMBER_MINTEMP 5 #define CHAMBER_MAXTEMP 60 #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target //#define CHAMBER_LIMIT_SWITCHING //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin //#define HEATER_CHAMBER_INVERTING false #endif

#if DISABLED(PIDTEMPBED) #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control #if ENABLED(BED_LIMIT_SWITCHING) #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS #endif #endif

/**

• Thermal Protection provides additional protection to your printer from damage
• and fire. Marlin always includes safe min and max temperature ranges which
• protect against a broken or disconnected thermistor wire.
• The issue: If a thermistor falls out, it will report the much lower
• temperature of the air in the room, and the the firmware will keep
• the heater on.
• The solution: Once the temperature reaches the target, start observing.
• If the temperature stays too far below the target (hysteresis) for too
• long (period), the firmware will halt the machine as a safety precaution.
• If you get false positives for "Thermal Runaway", increase
• THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) #define THERMAL_PROTECTION_PERIOD 40 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius

//#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303 #endif

/**

• Whenever an M104, M109, or M303 increases the target temperature, the
• firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature
• hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and
• requires a hard reset. This test restarts with any M104/M109/M303, but only
• if the current temperature is far enough below the target for a reliable
• test.
• If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD
• and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
• below 2. */ #define WATCH_TEMP_PERIOD 20 // Seconds #define WATCH_TEMP_INCREASE 2 // Degrees Celsius #endif

/**

• Thermal Protection parameters for the bed are just as above for hotends. */ #if ENABLED(THERMAL_PROTECTION_BED) #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius

/**

• As described above, except for the bed (M140/M190/M303). */ #define WATCH_BED_TEMP_PERIOD 60 // Seconds #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #endif

/**

• Thermal Protection parameters for the heated chamber. */ #if ENABLED(THERMAL_PROTECTION_CHAMBER) #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius

/**

• Heated chamber watch settings (M141/M191). */ #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius #endif

#if ENABLED(PIDTEMP) // Add an experimental additional term to the heater power, proportional to the extrusion speed. // A well-chosen Kc value should add just enough power to melt the increased material volume. //#define PID_EXTRUSION_SCALING #if ENABLED(PID_EXTRUSION_SCALING) #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) #define LPQ_MAX_LEN 50 #endif

/**

• Add an experimental additional term to the heater power, proportional to the fan speed.
• A well-chosen Kf value should add just enough power to compensate for power-loss from the cooling fan.
• You can either just add a constant compensation with the DEFAULT_Kf value
• or follow the instruction below to get speed-dependent compensation.
• Constant compensation (use only with fanspeeds of 0% and 100%)

• ---

• A good starting point for the Kf-value comes from the calculation:
• kf = (power_fan * eff_fan) / power_heater * 255
• where eff_fan is between 0.0 and 1.0, based on fan-efficiency and airflow to the nozzle / heater.
• Example:
• Heater: 40W, Fan: 0.1A * 24V = 2.4W, eff_fan = 0.8
• Kf = (2.4W * 0.8) / 40W * 255 = 12.24
• Fan-speed dependent compensation

• ---

• 1. To find a good Kf value, set the hotend temperature, wait for it to settle, and enable the fan (100%).
• Make sure PID_FAN_SCALING_LIN_FACTOR is 0 and PID_FAN_SCALING_ALTERNATIVE_DEFINITION is not enabled.
• If you see the temperature drop repeat the test, increasing the Kf value slowly, until the temperature
• drop goes away. If the temperature overshoots after enabling the fan, the Kf value is too big.
• 2. Note the Kf-value for fan-speed at 100%
• 3. Determine a good value for PID_FAN_SCALING_MIN_SPEED, which is around the speed, where the fan starts moving.
• 4. Repeat step 1. and 2. for this fan speed.
• 5. Enable PID_FAN_SCALING_ALTERNATIVE_DEFINITION and enter the two identified Kf-values in
• PID_FAN_SCALING_AT_FULL_SPEED and PID_FAN_SCALING_AT_MIN_SPEED. Enter the minimum speed in PID_FAN_SCALING_MIN_SPEED */ //#define PID_FAN_SCALING #if ENABLED(PID_FAN_SCALING) //#define PID_FAN_SCALING_ALTERNATIVE_DEFINITION #if ENABLED(PID_FAN_SCALING_ALTERNATIVE_DEFINITION) // The alternative definition is used for an easier configuration. // Just figure out Kf at fullspeed (255) and PID_FAN_SCALING_MIN_SPEED. // DEFAULT_Kf and PID_FAN_SCALING_LIN_FACTOR are calculated accordingly.

  #define PID_FAN_SCALING_AT_FULL_SPEED 13.0        //=PID_FAN_SCALING_LIN_FACTOR*255+DEFAULT_Kf
  #define PID_FAN_SCALING_AT_MIN_SPEED 6.0          //=PID_FAN_SCALING_LIN_FACTOR*PID_FAN_SCALING_MIN_SPEED+DEFAULT_Kf
  #define PID_FAN_SCALING_MIN_SPEED 10.0            // Minimum fan speed at which to enable PID_FAN_SCALING

  #define DEFAULT_Kf (255.0*PID_FAN_SCALING_AT_MIN_SPEED-PID_FAN_SCALING_AT_FULL_SPEED*PID_FAN_SCALING_MIN_SPEED)/(255.0-PID_FAN_SCALING_MIN_SPEED)
  #define PID_FAN_SCALING_LIN_FACTOR (PID_FAN_SCALING_AT_FULL_SPEED-DEFAULT_Kf)/255.0

#else
  #define PID_FAN_SCALING_LIN_FACTOR (0)             // Power loss due to cooling = Kf * (fan_speed)
  #define DEFAULT_Kf 10                              // A constant value added to the PID-tuner
  #define PID_FAN_SCALING_MIN_SPEED 10               // Minimum fan speed at which to enable PID_FAN_SCALING
#endif

#endif #endif

/**

• Automatic Temperature:
• The hotend target temperature is calculated by all the buffered lines of gcode.
• The maximum buffered steps/sec of the extruder motor is called "se".
• Start autotemp mode with M109 S B F
• The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
• mintemp and maxtemp. Turn this off by executing M109 without F*
• Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
• On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode */ #define AUTOTEMP #if ENABLED(AUTOTEMP) #define AUTOTEMP_OLDWEIGHT 0.98 #endif

// Show extra position information with 'M114 D' //#define M114_DETAIL

// Show Temperature ADC value // Enable for M105 to include ADC values read from temperature sensors. //#define SHOW_TEMP_ADC_VALUES

/**

• High Temperature Thermistor Support
• Thermistors able to support high temperature tend to have a hard time getting
• good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP
• will probably be caught when the heating element first turns on during the
• preheating process, which will trigger a min_temp_error as a safety measure
• and force stop everything.
• To circumvent this limitation, we allow for a preheat time (during which,
• min_temp_error won't be triggered) and add a min_temp buffer to handle
• aberrant readings.
• If you want to enable this feature for your hotend thermistor(s)
• uncomment and set values > 0 in the constants below */

// The number of consecutive low temperature errors that can occur // before a min_temp_error is triggered. (Shouldn't be more than 10.) //#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0

// The number of milliseconds a hotend will preheat before starting to check // the temperature. This value should NOT be set to the time it takes the // hot end to reach the target temperature, but the time it takes to reach // the minimum temperature your thermistor can read. The lower the better/safer. // This shouldn't need to be more than 30 seconds (30000) //#define MILLISECONDS_PREHEAT_TIME 0

// @section extruder

// Extruder runout prevention. // If the machine is idle and the temperature over MINTEMP // then extrude some filament every couple of SECONDS. //#define EXTRUDER_RUNOUT_PREVENT #if ENABLED(EXTRUDER_RUNOUT_PREVENT) #define EXTRUDER_RUNOUT_MINTEMP 190 #define EXTRUDER_RUNOUT_SECONDS 30 #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m) #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm) #endif

// @section temperature

// Calibration for AD595 / AD8495 sensor to adjust temperature measurements. // The final temperature is calculated as (measuredTemp * GAIN) + OFFSET. #define TEMP_SENSOR_AD595_OFFSET 0.0 #define TEMP_SENSOR_AD595_GAIN 1.0 #define TEMP_SENSOR_AD8495_OFFSET 0.0 #define TEMP_SENSOR_AD8495_GAIN 1.0

/**

• Controller Fan
• To cool down the stepper drivers and MOSFETs.
• The fan will turn on automatically whenever any stepper is enabled
• and turn off after a set period after all steppers are turned off. */ //#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled #define CONTROLLERFAN_SPEED 255 // 255 == full speed //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled #endif

// When first starting the main fan, run it at full speed for the // given number of milliseconds. This gets the fan spinning reliably // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) //#define FAN_KICKSTART_TIME 100

// Some coolers may require a non-zero "off" state. //#define FAN_OFF_PWM 1

/**

• PWM Fan Scaling
• Define the min/max speeds for PWM fans (as set with M106).
• With these options the M106 0-255 value range is scaled to a subset
• to ensure that the fan has enough power to spin, or to run lower
• current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
• Value 0 always turns off the fan.
• Define one or both of these to override the default 0-255 range. */ //#define FAN_MIN_PWM 50 //#define FAN_MAX_PWM 128

/**

• FAST PWM FAN Settings
• Use to change the FAST FAN PWM frequency (if enabled in Configuration.h)
• Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a
• frequency as close as possible to the desired frequency.
• FAST_PWM_FAN_FREQUENCY [undefined by default]
• Set this to your desired frequency.
• If left undefined this defaults to F = F_CPU/(22551)
• i.e., F = 31.4kHz on 16MHz microcontrollers or F = 39.2kHz on 20MHz microcontrollers.
• These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required
• NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior.
• USE_OCR2A_AS_TOP [undefined by default]
• Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2:
• 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz]
• 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz]
• A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of
• PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.)
• USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies. */ #if ENABLED(FAST_PWM_FAN) //#define FAST_PWM_FAN_FREQUENCY 31400 //#define USE_OCR2A_AS_TOP #endif

// @section extruder

/**

• Extruder cooling fans
• Extruder auto fans automatically turn on when their extruders'
• temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE.
• Your board's pins file specifies the recommended pins. Override those here
• or set to -1 to disable completely.
• Multiple extruders can be assigned to the same pin in which case
• the fan will turn on when any selected extruder is above the threshold. */ #define E0_AUTO_FAN_PIN P2_04 #define E1_AUTO_FAN_PIN -1 #define E2_AUTO_FAN_PIN -1 #define E3_AUTO_FAN_PIN -1 #define E4_AUTO_FAN_PIN -1 #define E5_AUTO_FAN_PIN -1 #define CHAMBER_AUTO_FAN_PIN -1

#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 #define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed #define CHAMBER_AUTO_FAN_TEMPERATURE 30 #define CHAMBER_AUTO_FAN_SPEED 255

/**

• Part-Cooling Fan Multiplexer
• This feature allows you to digitally multiplex the fan output.
• The multiplexer is automatically switched at tool-change.
• Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. */ #define FANMUX0_PIN -1 #define FANMUX1_PIN -1 #define FANMUX2_PIN -1

/**

• M355 Case Light on-off / brightness */ //#define CASE_LIGHT_ENABLE #if ENABLED(CASE_LIGHT_ENABLE) //#define CASE_LIGHT_PIN 4 // Override the default pin if needed #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) //#define CASE_LIGHT_MAX_PWM 128 // Limit pwm //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } #endif #endif

// @section homing

// If you want endstops to stay on (by default) even when not homing // enable this option. Override at any time with M120, M121. //#define ENDSTOPS_ALWAYS_ON_DEFAULT

// @section extras

//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.

// Employ an external closed loop controller. Override pins here if needed. //#define EXTERNAL_CLOSED_LOOP_CONTROLLER #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER) //#define CLOSED_LOOP_ENABLE_PIN -1 //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1 #endif

/**

• Dual Steppers / Dual Endstops
• This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes.
• For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to
• spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop
• set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug
• that should be used for the second endstop. Extra endstops will appear in the output of 'M119'.
• Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors
• this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error
• in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. */

//#define X_DUAL_STEPPER_DRIVERS #if ENABLED(X_DUAL_STEPPER_DRIVERS) #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions //#define X_DUAL_ENDSTOPS #if ENABLED(X_DUAL_ENDSTOPS) #define X2_USE_ENDSTOP XMAX #define X2_ENDSTOP_ADJUSTMENT 0 #endif #endif

//#define Y_DUAL_STEPPER_DRIVERS #if ENABLED(Y_DUAL_STEPPER_DRIVERS) #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions //#define Y_DUAL_ENDSTOPS #if ENABLED(Y_DUAL_ENDSTOPS) #define Y2_USE_ENDSTOP YMAX #define Y2_ENDSTOP_ADJUSTMENT 0 #endif #endif

// // For Z set the number of stepper drivers // #define NUM_Z_STEPPER_DRIVERS 1 // (1-4) Z options change based on how many

#if NUM_Z_STEPPER_DRIVERS > 1 //#define Z_MULTI_ENDSTOPS #if ENABLED(Z_MULTI_ENDSTOPS) #define Z2_USE_ENDSTOP XMAX #define Z2_ENDSTOP_ADJUSTMENT 0 #if NUM_Z_STEPPER_DRIVERS >= 3 #define Z3_USE_ENDSTOP YMAX #define Z3_ENDSTOP_ADJUSTMENT 0 #endif #if NUM_Z_STEPPER_DRIVERS >= 4 #define Z4_USE_ENDSTOP ZMAX #define Z4_ENDSTOP_ADJUSTMENT 0 #endif #endif #endif

/**

• Dual X Carriage
• This setup has two X carriages that can move independently, each with its own hotend.
• The carriages can be used to print an object with two colors or materials, or in
• "duplication mode" it can print two identical or X-mirrored objects simultaneously.
• The inactive carriage is parked automatically to prevent oozing.
• X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis.
• By default the X2 stepper is assigned to the first unused E plug on the board.
• The following Dual X Carriage modes can be selected with M605 S:
• 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel

•   results as long as it supports dual X-carriages. (M605 S0)
  

• 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so

•   that additional slicer support is not required. (M605 S1)
  

• 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with

•   the first X-carriage and extruder, to print 2 copies of the same object at the same time.
  

•   Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and
  

•   follow with M605 S2 to initiate duplicated movement.
  

• 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates

•   the movement of the first except the second extruder is reversed in the X axis.
  

•   Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and
  

•   follow with M605 S3 to initiate mirrored movement.
  

*/ //#define DUAL_X_CARRIAGE #if ENABLED(DUAL_X_CARRIAGE) #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS. // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops // without modifying the firmware (through the "M218 T1 X???" command). // Remember: you should set the second extruder x-offset to 0 in your slicer.

// This is the default power-up mode which can be later using M605. #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE

// Default x offset in duplication mode (typically set to half print bed width) #define DEFAULT_DUPLICATION_X_OFFSET 100

#endif // DUAL_X_CARRIAGE

// Activate a solenoid on the active extruder with M380. Disable all with M381. // Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. //#define EXT_SOLENOID

// @section homing

// Homing hits each endstop, retracts by these distances, then does a slower bump. #define X_HOME_BUMP_MM 5 #define Y_HOME_BUMP_MM 5 #define Z_HOME_BUMP_MM 2 #define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) #define QUICK_HOME // If homing includes X and Y, do a diagonal move initially //#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing

// When G28 is called, this option will make Y home before X //#define HOME_Y_BEFORE_X

// Enable this if X or Y can't home without homing the other axis first. //#define CODEPENDENT_XY_HOMING

#if ENABLED(BLTOUCH) /**

• Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
• Do not activate settings that the probe might not understand. Clones might misunderstand
• advanced commands.
• Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then

•   check the wiring of the BROWN, RED and ORANGE wires.
  

• Note: If the trigger signal of your probe is not being recognized, it has been very often

•   because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
  

•   like they would be with a real switch. So please check the wiring first.
  

• Settings for all BLTouch and clone probes: */

// Safety: The probe needs time to recognize the command. // Minimum command delay (ms). Enable and increase if needed. //#define BLTOUCH_DELAY 500

/**

• Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones: */

// Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful // in special cases, like noisy or filtered input configurations. //#define BLTOUCH_FORCE_SW_MODE

/**

• Settings for BLTouch Smart 3.0 and 3.1
• Summary:
• • Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
• • High-Speed mode
• • Disable LCD voltage options */

/**

• Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
• V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
• If disabled, OD mode is the hard-coded default on 3.0
• On startup, Marlin will compare its eeprom to this vale. If the selected mode
• differs, a mode set eeprom write will be completed at initialization.
• Use the option below to force an eeprom write to a V3.1 probe regardless. */ #define BLTOUCH_SET_5V_MODE

/**

• Safety: Activate if connecting a probe with an unknown voltage mode.
• V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
• V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
• To preserve the life of the probe, use this once then turn it off and re-flash. */ //#define BLTOUCH_FORCE_MODE_SET

/**

• Use "HIGH SPEED" mode for probing.
• Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems.
• This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
• If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state. */ //#define BLTOUCH_HS_MODE

// Safety: Enable voltage mode settings in the LCD menu. //#define BLTOUCH_LCD_VOLTAGE_MENU

#endif // BLTOUCH

/**

• Z Steppers Auto-Alignment
• Add the G34 command to align multiple Z steppers using a bed probe. */ //#define Z_STEPPER_AUTO_ALIGN #if ENABLED(Z_STEPPER_AUTO_ALIGN) // Define probe X and Y positions for Z1, Z2 [, Z3] #define Z_STEPPER_ALIGN_XY { { 10, 190 }, { 100, 10 }, { 190, 190 } }

// Provide Z stepper positions for more rapid convergence in bed alignment. // Currently requires triple stepper drivers. //#define Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS #if ENABLED(Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS) // Define Stepper XY positions for Z1, Z2, Z3 corresponding to // the Z screw positions in the bed carriage. // Define one position per Z stepper in stepper driver order. #define Z_STEPPER_ALIGN_STEPPER_XY { { 210.7, 102.5 }, { 152.6, 220.0 }, { 94.5, 102.5 } } #else // Amplification factor. Used to scale the correction step up or down. // In case the stepper (spindle) position is further out than the test point. // Use a value > 1. NOTE: This may cause instability #define Z_STEPPER_ALIGN_AMP 1.0 #endif

// Set number of iterations to align #define Z_STEPPER_ALIGN_ITERATIONS 3

// Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34

// On a 300mm bed a 5% grade would give a misalignment of ~1.5cm #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle

// Stop criterion. If the accuracy is better than this stop iterating early #define Z_STEPPER_ALIGN_ACC 0.02 #endif

// @section motion

#define AXIS_RELATIVE_MODES { false, false, false, false }

// Add a Duplicate option for well-separated conjoined nozzles //#define MULTI_NOZZLE_DUPLICATION

// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. #define INVERT_X_STEP_PIN false #define INVERT_Y_STEP_PIN false #define INVERT_Z_STEP_PIN false #define INVERT_E_STEP_PIN false

// Default stepper release if idle. Set to 0 to deactivate. // Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. // Time can be set by M18 and M84. #define DEFAULT_STEPPER_DEACTIVE_TIME 120 #define DISABLE_INACTIVE_X true #define DISABLE_INACTIVE_Y true #define DISABLE_INACTIVE_Z false // Set to false if the nozzle will fall down on your printed part when print has finished. #define DISABLE_INACTIVE_E true

#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate #define DEFAULT_MINTRAVELFEEDRATE 0.0

//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated

// Minimum time that a segment needs to take if the buffer is emptied #define DEFAULT_MINSEGMENTTIME 20000 // (ms)

// If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN

// Frequency limit // See nophead's blog for more info // Not working O //#define XY_FREQUENCY_LIMIT 15

// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end // of the buffer and all stops. This should not be much greater than zero and should only be changed // if unwanted behavior is observed on a user's machine when running at very slow speeds. #define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)

// // Backlash Compensation // Adds extra movement to axes on direction-changes to account for backlash. // //#define BACKLASH_COMPENSATION #if ENABLED(BACKLASH_COMPENSATION) // Define values for backlash distance and correction. // If BACKLASH_GCODE is enabled these values are the defaults. #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction

// Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments // to reduce print artifacts. (Enabling this is costly in memory and computation!) //#define BACKLASH_SMOOTHING_MM 3 // (mm)

// Add runtime configuration and tuning of backlash values (M425) //#define BACKLASH_GCODE

#if ENABLED(BACKLASH_GCODE) // Measure the Z backlash when probing (G29) and set with "M425 Z" #define MEASURE_BACKLASH_WHEN_PROBING

#if ENABLED(MEASURE_BACKLASH_WHEN_PROBING)
  // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT
  // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION
  // increments while checking for the contact to be broken.
  #define BACKLASH_MEASUREMENT_LIMIT       0.5   // (mm)
  #define BACKLASH_MEASUREMENT_RESOLUTION  0.005 // (mm)
  #define BACKLASH_MEASUREMENT_FEEDRATE    Z_PROBE_SPEED_SLOW // (mm/m)
#endif

#endif #endif

/**

• Automatic backlash, position and hotend offset calibration
• Enable G425 to run automatic calibration using an electrically-
• conductive cube, bolt, or washer mounted on the bed.
• G425 uses the probe to touch the top and sides of the calibration object
• on the bed and measures and/or correct positional offsets, axis backlash
• and hotend offsets.
• Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within

•   ±5mm of true values for G425 to succeed.
  

*/ //#define CALIBRATION_GCODE #if ENABLED(CALIBRATION_GCODE)

#define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm

#define CALIBRATION_FEEDRATE_SLOW 60 // mm/m #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m

// The following parameters refer to the conical section of the nozzle tip. #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm

// Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). //#define CALIBRATION_REPORTING

// The true location and dimension the cube/bolt/washer on the bed. #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm

// Comment out any sides which are unreachable by the probe. For best // auto-calibration results, all sides must be reachable. #define CALIBRATION_MEASURE_RIGHT #define CALIBRATION_MEASURE_FRONT #define CALIBRATION_MEASURE_LEFT #define CALIBRATION_MEASURE_BACK

// Probing at the exact top center only works if the center is flat. If // probing on a screwhead or hollow washer, probe near the edges. //#define CALIBRATION_MEASURE_AT_TOP_EDGES

// Define the pin to read during calibration #ifndef CALIBRATION_PIN #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin //#define CALIBRATION_PIN_PULLDOWN #define CALIBRATION_PIN_PULLUP #endif #endif

/**

• Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies
• below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible
• vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the
• lowest stepping frequencies. */ //#define ADAPTIVE_STEP_SMOOTHING

/**

• Custom Microstepping
• Override as-needed for your setup. Up to 3 MS pins are supported. */ //#define MICROSTEP1 LOW,LOW,LOW //#define MICROSTEP2 HIGH,LOW,LOW //#define MICROSTEP4 LOW,HIGH,LOW //#define MICROSTEP8 HIGH,HIGH,LOW //#define MICROSTEP16 LOW,LOW,HIGH //#define MICROSTEP32 HIGH,LOW,HIGH

// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. #define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16]

/**

• @section stepper motor current
• Some boards have a means of setting the stepper motor current via firmware.
• The power on motor currents are set by:
• PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2

•                     known compatible chips: A4982
  

• DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H

•                     known compatible chips: AD5206
  

• DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2

•                     known compatible chips: MCP4728
  

• DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE

•                     known compatible chips: MCP4451, MCP4018
  

• Motor currents can also be set by M907 - M910 and by the LCD.
• M907 - applies to all.
• M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
• M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 */ //#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps //#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) //#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis

// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) //#define DIGIPOT_I2C #if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) /**

• Common slave addresses:

•                    A   (A shifted)   B   (B shifted)  IC
  

• Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451
• AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451
• AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451
• AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451
• MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 */ #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT #endif

//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster #define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5 // Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. // These correspond to the physical drivers, so be mindful if the order is changed. #define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO

//=========================================================================== //=============================Additional Features=========================== //===========================================================================

// @section lcd

#if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 5060, 5060, 460, 260 } // Feedrates for manual moves along X, Y, Z, E from panel #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen #endif #endif

// Change values more rapidly when the encoder is rotated faster #define ENCODER_RATE_MULTIPLIER #if ENABLED(ENCODER_RATE_MULTIPLIER) #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed #endif

// Play a beep when the feedrate is changed from the Status Screen //#define BEEP_ON_FEEDRATE_CHANGE #if ENABLED(BEEP_ON_FEEDRATE_CHANGE) #define FEEDRATE_CHANGE_BEEP_DURATION 10 #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif

#if HAS_LCD_MENU

// Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU #if ENABLED(LCD_INFO_MENU) //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages #endif

// BACK menu items keep the highlight at the top //#define TURBO_BACK_MENU_ITEM

/**

• LED Control Menu
• Add LED Control to the LCD menu */ //#define LED_CONTROL_MENU #if ENABLED(LED_CONTROL_MENU) #define LED_COLOR_PRESETS // Enable the Preset Color menu option #if ENABLED(LED_COLOR_PRESETS) #define LED_USER_PRESET_RED 255 // User defined RED value #define LED_USER_PRESET_GREEN 128 // User defined GREEN value #define LED_USER_PRESET_BLUE 0 // User defined BLUE value #define LED_USER_PRESET_WHITE 255 // User defined WHITE value #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup #endif #endif

#endif // HAS_LCD_MENU

// Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING

// On the Info Screen, display XY with one decimal place when possible //#define LCD_DECIMAL_SMALL_XY

// The timeout (in ms) to return to the status screen from sub-menus //#define LCD_TIMEOUT_TO_STATUS 15000

// Add an 'M73' G-code to set the current percentage //#define LCD_SET_PROGRESS_MANUALLY

// Show the E position (filament used) during printing //#define LCD_SHOW_E_TOTAL

#if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits //#define SHOW_REMAINING_TIME // Display estimated time to completion #if ENABLED(SHOW_REMAINING_TIME) //#define USE_M73_REMAINING_TIME // Use remaining time from M73 command instead of estimation //#define ROTATE_PROGRESS_DISPLAY // Display (P)rogress, (E)lapsed, and (R)emaining time #endif #endif

#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing #if ENABLED(LCD_PROGRESS_BAR) #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar #endif #endif

#if ENABLED(SDSUPPORT)

// Some RAMPS and other boards don't detect when an SD card is inserted. You can work // around this by connecting a push button or single throw switch to the pin defined // as SD_DETECT_PIN in your board's pins definitions. // This setting should be disabled unless you are using a push button, pulling the pin to ground. // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). #define SD_DETECT_INVERTED

#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.

// Reverse SD sort to show "more recent" files first, according to the card's FAT. // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. #define SDCARD_RATHERRECENTFIRST

#define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing

//#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files

#define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27")

/**

• Continue after Power-Loss (Creality3D)
• Store the current state to the SD Card at the start of each layer
• during SD printing. If the recovery file is found at boot time, present
• an option on the LCD screen to continue the print from the last-known
• point in the file. */ //#define POWER_LOSS_RECOVERY #if ENABLED(POWER_LOSS_RECOVERY) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.

// Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
// especially with "vase mode" printing. Set too high and vases cannot be continued.
#define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data

#endif

/**

• Sort SD file listings in alphabetical order.
• With this option enabled, items on SD cards will be sorted
• by name for easier navigation.
• By default...
• • Use the slowest -but safest- method for sorting.
• • Folders are sorted to the top.
• • The sort key is statically allocated.
• • No added G-code (M34) support.
• • 40 item sorting limit. (Items after the first 40 are unsorted.)
• SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the
• compiler to calculate the worst-case usage and throw an error if the SRAM
• limit is exceeded.
• • SDSORT_USES_RAM provides faster sorting via a static directory buffer.
• • SDSORT_USES_STACK does the same, but uses a local stack-based buffer.
• • SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
• • SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) */ //#define SDCARD_SORT_ALPHA

// SD Card Sorting options #if ENABLED(SDCARD_SORT_ALPHA) #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. #define FOLDER_SORTING -1 // -1=above 0=none 1=below #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting. #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. #endif

// This allows hosts to request long names for files and folders with M33 //#define LONG_FILENAME_HOST_SUPPORT

// Enable this option to scroll long filenames in the SD card menu #define SCROLL_LONG_FILENAMES

// Leave the heaters on after Stop Print (not recommended!) //#define SD_ABORT_NO_COOLDOWN

/**

• This option allows you to abort SD printing when any endstop is triggered.
• This feature must be enabled with "M540 S1" or from the LCD menu.
• To have any effect, endstops must be enabled during SD printing. */ //#define SD_ABORT_ON_ENDSTOP_HIT

/**

• This option makes it easier to print the same SD Card file again.
• On print completion the LCD Menu will open with the file selected.
• You can just click to start the print, or navigate elsewhere. */ //#define SD_REPRINT_LAST_SELECTED_FILE

/**

• Auto-report SdCard status with M27 S */ //#define AUTO_REPORT_SD_STATUS

/**

• Support for USB thumb drives using an Arduino USB Host Shield or
• equivalent MAX3421E breakout board. The USB thumb drive will appear
• to Marlin as an SD card.
• The MAX3421E can be assigned the same pins as the SD card reader, with
• the following pin mapping:
• SCLK, MOSI, MISO --> SCLK, MOSI, MISO
• INT --> SD_DETECT_PIN [1]
• SS --> SDSS
• [1] On AVR an interrupt-capable pin is best for UHS3 compatibility. */ //#define USB_FLASH_DRIVE_SUPPORT #if ENABLED(USB_FLASH_DRIVE_SUPPORT) #define USB_CS_PIN SDSS #define USB_INTR_PIN SD_DETECT_PIN

/**
 * USB Host Shield Library
 *
 * - UHS2 uses no interrupts and has been production-tested
 *   on a LulzBot TAZ Pro with a 32-bit Archim board.
 *
 * - UHS3 is newer code with better USB compatibility. But it
 *   is less tested and is known to interfere with Servos.
 *   [1] This requires USB_INTR_PIN to be interrupt-capable.
 */
//#define USE_UHS3_USB

#endif

/**

• When using a bootloader that supports SD-Firmware-Flashing,
• add a menu item to activate SD-FW-Update on the next reboot.
• Requires ATMEGA2560 (Arduino Mega)
• Tested with this bootloader:
• https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560 */ //#define SD_FIRMWARE_UPDATE #if ENABLED(SD_FIRMWARE_UPDATE) #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0 #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF #endif

// Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER

#if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * * LCD - Use the SD drive in the external LCD controller. * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). * * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] */ //#define SDCARD_CONNECTION LCD #endif

#endif // SDSUPPORT

/**

• By default an onboard SD card reader may be shared as a USB mass-
• storage device. This option hides the SD card from the host PC. */ //#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security).

/**

• Additional options for Graphical Displays
• Use the optimizations here to improve printing performance,
• which can be adversely affected by graphical display drawing,
• especially when doing several short moves, and when printing
• on DELTA and SCARA machines.
• Some of these options may result in the display lagging behind
• controller events, as there is a trade-off between reliable
• printing performance versus fast display updates. */ #if HAS_GRAPHICAL_LCD // Show SD percentage next to the progress bar //#define DOGM_SD_PERCENT

// Enable to save many cycles by drawing a hollow frame on the Info Screen #define XYZ_HOLLOW_FRAME

// Enable to save many cycles by drawing a hollow frame on Menu Screens #define MENU_HOLLOW_FRAME

// A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. //#define USE_BIG_EDIT_FONT

// A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. //#define USE_SMALL_INFOFONT

// Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5

// Swap the CW/CCW indicators in the graphics overlay //#define OVERLAY_GFX_REVERSE

/**

• ST7920-based LCDs can emulate a 16 x 4 character display using
• the ST7920 character-generator for very fast screen updates.
• Enable LIGHTWEIGHT_UI to use this special display mode.
• Since LIGHTWEIGHT_UI has limited space, the position and status
• message occupy the same line. Set STATUS_EXPIRE_SECONDS to the
• length of time to display the status message before clearing.
• Set STATUS_EXPIRE_SECONDS to zero to never clear the status.
• This will prevent position updates from being displayed. */ #if ENABLED(U8GLIB_ST7920) //#define LIGHTWEIGHT_UI #if ENABLED(LIGHTWEIGHT_UI) #define STATUS_EXPIRE_SECONDS 20 #endif #endif

/**

• Status (Info) Screen customizations
• These options may affect code size and screen render time.
• Custom status screens can forcibly override these settings. */ //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends) #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames //#define STATUS_HEAT_PERCENT // Show heating in a progress bar //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.

// Frivolous Game Options //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu

#endif // HAS_GRAPHICAL_LCD

// // Additional options for DGUS / DWIN displays // #if HAS_DGUS_LCD #define DGUS_SERIAL_PORT 2 #define DGUS_BAUDRATE 115200

#define DGUS_RX_BUFFER_SIZE 128 #define DGUS_TX_BUFFER_SIZE 48 //#define DGUS_SERIAL_STATS_RX_BUFFER_OVERRUNS // Fix Rx overrun situation (Currently only for AVR)

#define DGUS_UPDATE_INTERVAL_MS 500 // (ms) Interval between automatic screen updates #define BOOTSCREEN_TIMEOUT 3000 // (ms) Duration to display the boot screen

#if EITHER(DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_HIPRECY) #define DGUS_PRINT_FILENAME // Display the filename during printing #define DGUS_PREHEAT_UI // Display a preheat screen during heatup

#if ENABLED(DGUS_LCD_UI_FYSETC)
  //#define DUGS_UI_MOVE_DIS_OPTION   // Disabled by default for UI_FYSETC
#else
  #define DUGS_UI_MOVE_DIS_OPTION     // Enabled by default for UI_HIPRECY
#endif

#define DGUS_FILAMENT_LOADUNLOAD
#if ENABLED(DGUS_FILAMENT_LOADUNLOAD)
  #define DGUS_FILAMENT_PURGE_LENGTH 10
  #define DGUS_FILAMENT_LOAD_LENGTH_PER_TIME 0.5 // (mm) Adjust in proportion to DGUS_UPDATE_INTERVAL_MS
#endif

#define DGUS_UI_WAITING               // Show a "waiting" screen between some screens
#if ENABLED(DGUS_UI_WAITING)
  #define DGUS_UI_WAITING_STATUS 10
  #define DGUS_UI_WAITING_STATUS_PERIOD 8 // Increase to slower waiting status looping
#endif

#endif #endif // HAS_DGUS_LCD

// // Touch UI for the FTDI Embedded Video Engine (EVE) // #if ENABLED(TOUCH_UI_FTDI_EVE) // Display board used //#define LCD_FTDI_VM800B35A // FTDI 3.5" with FT800 (320x240) //#define LCD_4DSYSTEMS_4DLCD_FT843 // 4D Systems 4.3" (480x272) //#define LCD_HAOYU_FT800CB // Haoyu with 4.3" or 5" (480x272) //#define LCD_HAOYU_FT810CB // Haoyu with 5" (800x480) //#define LCD_ALEPHOBJECTS_CLCD_UI // Aleph Objects Color LCD UI

// Correct the resolution if not using the stock TFT panel. //#define TOUCH_UI_320x240 //#define TOUCH_UI_480x272 //#define TOUCH_UI_800x480

// Mappings for boards with a standard RepRapDiscount Display connector //#define AO_EXP1_PINMAP // AlephObjects CLCD UI EXP1 mapping //#define AO_EXP2_PINMAP // AlephObjects CLCD UI EXP2 mapping //#define CR10_TFT_PINMAP // Rudolph Riedel's CR10 pin mapping //#define OTHER_PIN_LAYOUT // Define pins manually below #if ENABLED(OTHER_PIN_LAYOUT) // The pins for CS and MOD_RESET (PD) must be chosen. #define CLCD_MOD_RESET 9 #define CLCD_SPI_CS 10

// If using software SPI, specify pins for SCLK, MOSI, MISO
//#define CLCD_USE_SOFT_SPI
#if ENABLED(CLCD_USE_SOFT_SPI)
  #define CLCD_SOFT_SPI_MOSI 11
  #define CLCD_SOFT_SPI_MISO 12
  #define CLCD_SOFT_SPI_SCLK 13
#endif

#endif

// Display Orientation. An inverted (i.e. upside-down) display // is supported on the FT800. The FT810 and beyond also support // portrait and mirrored orientations. //#define TOUCH_UI_INVERTED //#define TOUCH_UI_PORTRAIT //#define TOUCH_UI_MIRRORED

// UTF8 processing and rendering. // Unsupported characters are shown as '?'. //#define TOUCH_UI_USE_UTF8 #if ENABLED(TOUCH_UI_USE_UTF8) // Western accents support. These accented characters use // combined bitmaps and require relatively little storage. #define TOUCH_UI_UTF8_WESTERN_CHARSET #if ENABLED(TOUCH_UI_UTF8_WESTERN_CHARSET) // Additional character groups. These characters require // full bitmaps and take up considerable storage: //#define TOUCH_UI_UTF8_SUPERSCRIPTS // ¹ ² ³ //#define TOUCH_UI_UTF8_COPYRIGHT // © ® //#define TOUCH_UI_UTF8_GERMANIC // ß //#define TOUCH_UI_UTF8_SCANDINAVIAN // Æ Ð Ø Þ æ ð ø þ //#define TOUCH_UI_UTF8_PUNCTUATION // « » ¿ ¡ //#define TOUCH_UI_UTF8_CURRENCY // ¢ £ ¤ ¥ //#define TOUCH_UI_UTF8_ORDINALS // º ª //#define TOUCH_UI_UTF8_MATHEMATICS // ± × ÷ //#define TOUCH_UI_UTF8_FRACTIONS // ¼ ½ ¾ //#define TOUCH_UI_UTF8_SYMBOLS // µ ¶ ¦ § ¬ #endif #endif

// Use a smaller font when labels don't fit buttons #define TOUCH_UI_FIT_TEXT

// Allow language selection from menu at run-time (otherwise use LCD_LANGUAGE) //#define LCD_LANGUAGE_1 en //#define LCD_LANGUAGE_2 fr //#define LCD_LANGUAGE_3 de //#define LCD_LANGUAGE_4 es //#define LCD_LANGUAGE_5 it

// Use a numeric passcode for "Screen lock" keypad. // (recommended for smaller displays) //#define TOUCH_UI_PASSCODE

// Output extra debug info for Touch UI events //#define TOUCH_UI_DEBUG

// Developer menu (accessed by touching "About Printer" copyright text) //#define TOUCH_UI_DEVELOPER_MENU #endif

// // FSMC Graphical TFT // #if ENABLED(FSMC_GRAPHICAL_TFT) //#define TFT_MARLINUI_COLOR 0xFFFF // White //#define TFT_MARLINBG_COLOR 0x0000 // Black //#define TFT_DISABLED_COLOR 0x0003 // Almost black //#define TFT_BTCANCEL_COLOR 0xF800 // Red //#define TFT_BTARROWS_COLOR 0xDEE6 // 11011 110111 00110 Yellow //#define TFT_BTOKMENU_COLOR 0x145F // 00010 100010 11111 Cyan #endif

// // ADC Button Debounce // #if HAS_ADC_BUTTONS #define ADC_BUTTON_DEBOUNCE_DELAY 16 // (ms) Increase if buttons bounce or repeat too fast #endif

// @section safety

/**

• The watchdog hardware timer will do a reset and disable all outputs
• if the firmware gets too overloaded to read the temperature sensors.
• If you find that watchdog reboot causes your AVR board to hang forever,
• enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO.
• NOTE: This method is less reliable as it can only catch hangups while
• interrupts are enabled. */ #define USE_WATCHDOG #if ENABLED(USE_WATCHDOG) //#define WATCHDOG_RESET_MANUAL #endif

// @section lcd

/**

• Babystepping enables movement of the axes by tiny increments without changing
• the current position values. This feature is used primarily to adjust the Z
• axis in the first layer of a print in real-time.
• Warning: Does not respect endstops! */ #define BABYSTEPPING #if ENABLED(BABYSTEPPING) //#define BABYSTEP_WITHOUT_HOMING //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way #define BABYSTEP_MULTIPLICATOR_Z 10 // Babysteps are very small. Increase for faster motion. #define BABYSTEP_MULTIPLICATOR_XY 1

#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. // Note: Extra time may be added to mitigate controller latency. //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. #if ENABLED(MOVE_Z_WHEN_IDLE) #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. #endif #endif

//#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28

#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping #if ENABLED(BABYSTEP_ZPROBE_OFFSET) //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor #endif #endif

// @section extruder

/**

• Linear Pressure Control v1.5
• Assumption: advance [steps] = k * (delta velocity [steps/s])
• K=0 means advance disabled.
• NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions!
• Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak.
• Larger K values will be needed for flexible filament and greater distances.
• If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk)
• print acceleration will be reduced during the affected moves to keep within the limit.
• See http://marlinfw.org/docs/features/lin_advance.html for full instructions.
• Mention @Sebastianv650 on GitHub to alert the author of any issues. */ //#define LIN_ADVANCE #if ENABLED(LIN_ADVANCE) //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed //#define LA_DEBUG // If enabled, this will generate debug information output over USB. #endif

// @section leveling

/**

• Points to probe for all 3-point Leveling procedures.
• Override if the automatically selected points are inadequate. */ #if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) //#define PROBE_PT_1_X 15 //#define PROBE_PT_1_Y 180 //#define PROBE_PT_2_X 15 //#define PROBE_PT_2_Y 20 //#define PROBE_PT_3_X 170 //#define PROBE_PT_3_Y 20 #endif

/**

• Override MIN_PROBE_EDGE for each side of the build plate
• Useful to get probe points to exact positions on targets or
• to allow leveling to avoid plate clamps on only specific
• sides of the bed. With NOZZLE_AS_PROBE negative values are
• allowed, to permit probing outside the bed.
• If you are replacing the prior *_PROBE_BED_POSITION options,
• LEFT and FRONT values in most cases will map directly over
• RIGHT and REAR would be the inverse such as
• (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION)
• This will allow all positions to match at compilation, however
• should the probe position be modified with M851XY then the
• probe points will follow. This prevents any change from causing
• the probe to be unable to reach any points. */ #if PROBE_SELECTED && !IS_KINEMATIC //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE #endif

#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) // Override the mesh area if the automatic (max) area is too large //#define MESH_MIN_X MESH_INSET //#define

[bdelia]

Hey @MDRudnicki , thanks for this. I may be missing it in the cut and paste, but did you also share your Configuration.h file? I seem to only see the Configuration_adv.h file. If you could also share the Configuration.h file that would be great.

Also, if you could attach them rather than cut and paste that might be easier.

Many thanks!

[MDRudnicki]

Here are my configuration files

On Fri, May 1, 2020 at 10:55 AM Brett Delia [email protected] wrote:

Hey @MDRudnicki https://github.com/MDRudnicki , thanks for this. I may be missing it in the cut and paste, but did you also share your Configuration.h file? I seem to only see the Configuration_adv.h file. If you could also share the Configuration.h file that would be great.

Also, if you could attach them rather than cut and paste that might be easier.

Many thanks!

— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/bigtreetech/BIGTREETECH-TFT35-V1.2/issues/9#issuecomment-622445164, or unsubscribe https://github.com/notifications/unsubscribe-auth/AOFAIJJKNRKTSLGCMXGE7WTRPLWHBANCNFSM4HGMZEMA .

/**

• Marlin 3D Printer Firmware
• Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
• Based on Sprinter and grbl.
• Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
• This program is free software: you can redistribute it and/or modify
• it under the terms of the GNU General Public License as published by
• the Free Software Foundation, either version 3 of the License, or
• (at your option) any later version.
• This program is distributed in the hope that it will be useful,
• but WITHOUT ANY WARRANTY; without even the implied warranty of
• MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
• GNU General Public License for more details.
• You should have received a copy of the GNU General Public License
• along with this program. If not, see http://www.gnu.org/licenses/.

*/ #pragma once

/**

• Configuration.h
• Basic settings such as:
• • Type of electronics
• • Type of temperature sensor
• • Printer geometry
• • Endstop configuration
• • LCD controller
• • Extra features
• Advanced settings can be found in Configuration_adv.h

*/ #define CONFIGURATION_H_VERSION 020000

//=========================================================================== //============================= Getting Started ============================= //===========================================================================

/**

• Here are some standard links for getting your machine calibrated:
• http://reprap.org/wiki/Calibration
• http://youtu.be/wAL9d7FgInk
• http://calculator.josefprusa.cz
• http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
• http://www.thingiverse.com/thing:5573
• https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
• http://www.thingiverse.com/thing:298812 */

//=========================================================================== //============================= DELTA Printer =============================== //=========================================================================== // For a Delta printer start with one of the configuration files in the // config/examples/delta directory and customize for your machine. //

//=========================================================================== //============================= SCARA Printer =============================== //=========================================================================== // For a SCARA printer start with the configuration files in // config/examples/SCARA and customize for your machine. //

// @section info

// Author info of this build printed to the host during boot and M115 #define STRING_CONFIG_H_AUTHOR "(thisiskeithb, Ender-5)" // Who made the changes. //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)

/**

• *** VENDORS PLEASE READ ***
• Marlin allows you to add a custom boot image for Graphical LCDs.
• With this option Marlin will first show your custom screen followed
• by the standard Marlin logo with version number and web URL.
• We encourage you to take advantage of this new feature and we also
• respectfully request that you retain the unmodified Marlin boot screen. */

// Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION ** #define SHOW_BOOTSCREEN

// Show the bitmap in Marlin/_Bootscreen.h on startup. #define SHOW_CUSTOM_BOOTSCREEN

// Show the bitmap in Marlin/_Statusscreen.h on the status screen. #define CUSTOM_STATUS_SCREEN_IMAGE

// @section machine

/**

• Select the serial port on the board to use for communication with the host.
• This allows the connection of wireless adapters (for instance) to non-default port pins.
• Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
• :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0

/**

• Select a secondary serial port on the board to use for communication with the host.
• This allows the connection of wireless adapters (for instance) to non-default port pins.
• Serial port -1 is the USB emulated serial port, if available.
• :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT_2 -1

//#define SERIAL_PORT_3 6

/**

• This setting determines the communication speed of the printer.
• 250000 works in most cases, but you might try a lower speed if
• you commonly experience drop-outs during host printing.
• You may try up to 1000000 to speed up SD file transfer.
• :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] */ #define BAUDRATE 115200

// Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH

// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_BIGTREE_SKR_V1_3 #endif

// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Ender-5"

// Printer's unique ID, used by some programs to differentiate between machines. // Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"

// @section extruder

// This defines the number of extruders // :[1, 2, 3, 4, 5, 6, 7, 8] #define EXTRUDERS 1

// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75

// For Cyclops or any "multi-extruder" that shares a single nozzle. //#define SINGLENOZZLE

/**

• Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
• This device allows one stepper driver on a control board to drive
• two to eight stepper motors, one at a time, in a manner suitable
• for extruders.
• This option only allows the multiplexer to switch on tool-change.
• Additional options to configure custom E moves are pending. */ //#define MK2_MULTIPLEXER #if ENABLED(MK2_MULTIPLEXER) // Override the default DIO selector pins here, if needed. // Some pins files may provide defaults for these pins. //#define E_MUX0_PIN 40 // Always Required //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs #endif

/**

• Prusa Multi-Material Unit v2
• Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
• Requires EXTRUDERS = 5
• For additional configuration see Configuration_adv.h */ //#define PRUSA_MMU2

// A dual extruder that uses a single stepper motor //#define SWITCHING_EXTRUDER #if ENABLED(SWITCHING_EXTRUDER) #define SWITCHING_EXTRUDER_SERVO_NR 0 #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] #if EXTRUDERS > 3 #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 #endif #endif

// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles //#define SWITCHING_NOZZLE #if ENABLED(SWITCHING_NOZZLE) #define SWITCHING_NOZZLE_SERVO_NR 0 //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo) #endif

/**

• Two separate X-carriages with extruders that connect to a moving part
• via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN. */ //#define PARKING_EXTRUDER

/**

• Two separate X-carriages with extruders that connect to a moving part
• via a magnetic docking mechanism using movements and no solenoid
• project : https://www.thingiverse.com/thing:3080893
• movements : https://youtu.be/0xCEiG9VS3k

•         https://youtu.be/Bqbcs0CU2FE
  

*/ //#define MAGNETIC_PARKING_EXTRUDER

#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)

#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381

#if ENABLED(PARKING_EXTRUDER)

#define PARKING_EXTRUDER_SOLENOIDS_INVERT           // If enabled, the solenoid is NOT magnetized with applied voltage
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW  // LOW or HIGH pin signal energizes the coil
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250        // (ms) Delay for magnetic field. No delay if 0 or not defined.
//#define MANUAL_SOLENOID_CONTROL                   // Manual control of docking solenoids with M380 S / M381

#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)

#define MPE_FAST_SPEED      9000      // (mm/m) Speed for travel before last distance point
#define MPE_SLOW_SPEED      4500      // (mm/m) Speed for last distance travel to park and couple
#define MPE_TRAVEL_DISTANCE   10      // (mm) Last distance point
#define MPE_COMPENSATION       0      // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling

#endif

#endif

/**

• Switching Toolhead
• Support for swappable and dockable toolheads, such as
• the E3D Tool Changer. Toolheads are locked with a servo. */ //#define SWITCHING_TOOLHEAD

/**

• Magnetic Switching Toolhead
• Support swappable and dockable toolheads with a magnetic
• docking mechanism using movement and no servo. */ //#define MAGNETIC_SWITCHING_TOOLHEAD

/**

• Electromagnetic Switching Toolhead
• Parking for CoreXY / HBot kinematics.
• Toolheads are parked at one edge and held with an electromagnet.
• Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4 */ //#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD

#if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders #if ENABLED(SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock #if ENABLED(PRIME_BEFORE_REMOVE) #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif #endif

/**

• "Mixing Extruder"
• • Adds G-codes M163 and M164 to set and "commit" the current mix factors.
• • Extends the stepping routines to move multiple steppers in proportion to the mix.
• • Optional support for Repetier Firmware's 'M164 S' supporting virtual tools.
• • This implementation supports up to two mixing extruders.
• • Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). */ //#define MIXING_EXTRUDER #if ENABLED(MIXING_EXTRUDER) #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD #if ENABLED(GRADIENT_MIX) //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias #endif #endif

// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. //#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle //#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle //#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle

// @section machine

/**

• Power Supply Control
• Enable and connect the power supply to the PS_ON_PIN.
• Specify whether the power supply is active HIGH or active LOW. */ //#define PSU_CONTROL //#define PSU_NAME "Power Supply"

#if ENABLED(PSU_CONTROL) #define PSU_ACTIVE_HIGH false // Set 'false' for ATX, 'true' for X-Box

//#define PSU_DEFAULT_OFF // Keep power off until enabled directly with M80 //#define PSU_POWERUP_DELAY 100 // (ms) Delay for the PSU to warm up to full power

//#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin #if ENABLED(AUTO_POWER_CONTROL) #define AUTO_POWER_FANS // Turn on PSU if fans need power #define AUTO_POWER_E_FANS #define AUTO_POWER_CONTROLLERFAN #define AUTO_POWER_CHAMBER_FAN //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature #define POWER_TIMEOUT 30 #endif #endif

// @section temperature

//=========================================================================== //============================= Thermal Settings ============================ //===========================================================================

/**

• --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
• Temperature sensors available:
• -5 : PT100 / PT1000 with MAX31865 (only for sensors 0-1)
• -3 : thermocouple with MAX31855 (only for sensors 0-1)
• -2 : thermocouple with MAX6675 (only for sensors 0-1)
• -4 : thermocouple with AD8495
• -1 : thermocouple with AD595

• 0 : not used
  

• 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
  

• 331 : (3.3V scaled thermistor 1 table for MEGA)
• 332 : (3.3V scaled thermistor 1 table for DUE)

• 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
  

• 3 : Mendel-parts thermistor (4.7k pullup)
  

• 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  

• 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)
  

• 501 : 100K Zonestar (Tronxy X3A) Thermistor
• 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)

• 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  

• 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  

• 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)

• 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
  

• 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
  

• 10 : 100k RS thermistor 198-961 (4.7k pullup)
• 11 : 100k beta 3950 1% thermistor (4.7k pullup)
• 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
• 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
• 15 : 100k thermistor calibration for JGAurora A5 hotend
• 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327
• 20 : Pt100 with circuit in the Ultimainboard V2.x with 5v excitation (AVR)
• 21 : Pt100 with circuit in the Ultimainboard V2.x with 3.3v excitation (STM32 \ LPC176x....)
• 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x
• 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
• 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup
• 66 : 4.7M High Temperature thermistor from Dyze Design
• 67 : 450C thermistor from SliceEngineering
• 70 : the 100K thermistor found in the bq Hephestos 2
• 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
• 99 : 100k thermistor with a 10K pull-up resistor (found on some Wanhao i3 machines)

•   1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
  

•                          (but gives greater accuracy and more stable PID)
  

• 51 : 100k thermistor - EPCOS (1k pullup)
• 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
• 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
• 1047 : Pt1000 with 4k7 pullup
• 1010 : Pt1000 with 1k pullup (non standard)
• 147 : Pt100 with 4k7 pullup
• 110 : Pt100 with 1k pullup (non standard)
• 1000 : Custom - Specify parameters in Configuration_adv.h

•     Use these for Testing or Development purposes. NEVER for production machine.
  

• 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
• 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 #define TEMP_SENSOR_2 0 #define TEMP_SENSOR_3 0 #define TEMP_SENSOR_4 0 #define TEMP_SENSOR_5 0 #define TEMP_SENSOR_6 0 #define TEMP_SENSOR_7 0 #define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_PROBE 0 #define TEMP_SENSOR_CHAMBER 0

// Dummy thermistor constant temperature readings, for use with 998 and 999 #define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_999_VALUE 100

// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings // from the two sensors differ too much the print will be aborted. //#define TEMP_SENSOR_1_AS_REDUNDANT #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10

#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109 #define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer #define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target

#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190 #define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer #define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target

// Below this temperature the heater will be switched off // because it probably indicates a broken thermistor wire. #define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5 #define HEATER_4_MINTEMP 5 #define HEATER_5_MINTEMP 5 #define HEATER_6_MINTEMP 5 #define HEATER_7_MINTEMP 5 #define BED_MINTEMP 5

// Above this temperature the heater will be switched off. // This can protect components from overheating, but NOT from shorts and failures. // (Use MINTEMP for thermistor short/failure protection.) #define HEATER_0_MAXTEMP 275 #define HEATER_1_MAXTEMP 275 #define HEATER_2_MAXTEMP 275 #define HEATER_3_MAXTEMP 275 #define HEATER_4_MAXTEMP 275 #define HEATER_5_MAXTEMP 275 #define HEATER_6_MAXTEMP 275 #define HEATER_7_MAXTEMP 275 #define BED_MAXTEMP 125

//=========================================================================== //============================= PID Settings ================================ //=========================================================================== // PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning

// Comment the following line to disable PID and enable bang-bang. #define PIDTEMP #define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current #define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current #define PID_K1 0.95 // Smoothing factor within any PID loop #if ENABLED(PIDTEMP) #define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) #define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) //#define PID_DEBUG // Sends debug data to the serial port. //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) // Set/get with gcode: M301 E[extruder number, 0-2] #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.

// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it // Creality Ender-5 #define DEFAULT_Kp 29.86 #define DEFAULT_Ki 3.37 #define DEFAULT_Kd 66.04

// Ultimaker //#define DEFAULT_Kp 22.2 //#define DEFAULT_Ki 1.08 //#define DEFAULT_Kd 114

// MakerGear //#define DEFAULT_Kp 7.0 //#define DEFAULT_Ki 0.1 //#define DEFAULT_Kd 12

// Mendel Parts V9 on 12V //#define DEFAULT_Kp 63.0 //#define DEFAULT_Ki 2.25 //#define DEFAULT_Kd 440

#endif // PIDTEMP

//=========================================================================== //====================== PID > Bed Temperature Control ====================== //===========================================================================

/**

• PID Bed Heating
• If this option is enabled set PID constants below.
• If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
• The PID frequency will be the same as the extruder PWM.
• If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
• which is fine for driving a square wave into a resistive load and does not significantly
• impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
• heater. If your configuration is significantly different than this and you don't understand
• the issues involved, don't use bed PID until someone else verifies that your hardware works. */ //#define PIDTEMPBED

//#define BED_LIMIT_SWITCHING

/**

• Max Bed Power
• Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
• When set to any value below 255, enables a form of PWM to the bed that acts like a divider
• so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) */ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current

#if ENABLED(PIDTEMPBED) //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port.

//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) #define DEFAULT_bedKp 10.00 #define DEFAULT_bedKi .023 #define DEFAULT_bedKd 305.4

//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) //from pidautotune //#define DEFAULT_bedKp 97.1 //#define DEFAULT_bedKi 1.41 //#define DEFAULT_bedKd 1675.16

// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED

// @section extruder

/**

• Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
• Add M302 to set the minimum extrusion temperature and/or turn
• cold extrusion prevention on and off.
• *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** */ #define PREVENT_COLD_EXTRUSION #define EXTRUDE_MINTEMP 170

/**

• Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
• Note: For Bowden Extruders make this large enough to allow load/unload. */ #define PREVENT_LENGTHY_EXTRUDE #define EXTRUDE_MAXLENGTH 200

//=========================================================================== //======================== Thermal Runaway Protection ======================= //===========================================================================

/**

• Thermal Protection provides additional protection to your printer from damage
• and fire. Marlin always includes safe min and max temperature ranges which
• protect against a broken or disconnected thermistor wire.
• The issue: If a thermistor falls out, it will report the much lower
• temperature of the air in the room, and the the firmware will keep
• the heater on.
• If you get "Thermal Runaway" or "Heating failed" errors the
• details can be tuned in Configuration_adv.h */

#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber

//=========================================================================== //============================= Mechanical Settings ========================= //===========================================================================

// @section machine

// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics // either in the usual order or reversed //#define COREXY //#define COREXZ //#define COREYZ //#define COREYX //#define COREZX //#define COREZY

//=========================================================================== //============================== Endstop Settings =========================== //===========================================================================

// @section homing

// Specify here all the endstop connectors that are connected to any endstop or probe. // Almost all printers will be using one per axis. Probes will use one or more of the // extra connectors. Leave undefined any used for non-endstop and non-probe purposes. //#define USE_XMIN_PLUG //#define USE_YMIN_PLUG #define USE_ZMIN_PLUG #define USE_XMAX_PLUG #define USE_YMAX_PLUG //#define USE_ZMAX_PLUG

// Enable pullup for all endstops to prevent a floating state #define ENDSTOPPULLUPS #if DISABLED(ENDSTOPPULLUPS) // Disable ENDSTOPPULLUPS to set pullups individually //#define ENDSTOPPULLUP_XMAX //#define ENDSTOPPULLUP_YMAX //#define ENDSTOPPULLUP_ZMAX //#define ENDSTOPPULLUP_XMIN //#define ENDSTOPPULLUP_YMIN //#define ENDSTOPPULLUP_ZMIN #define ENDSTOPPULLUP_ZMIN_PROBE #endif

// Enable pulldown for all endstops to prevent a floating state //#define ENDSTOPPULLDOWNS #if DISABLED(ENDSTOPPULLDOWNS) // Disable ENDSTOPPULLDOWNS to set pulldowns individually //#define ENDSTOPPULLDOWN_XMAX //#define ENDSTOPPULLDOWN_YMAX //#define ENDSTOPPULLDOWN_ZMAX //#define ENDSTOPPULLDOWN_XMIN //#define ENDSTOPPULLDOWN_YMIN //#define ENDSTOPPULLDOWN_ZMIN //#define ENDSTOPPULLDOWN_ZMIN_PROBE #endif

// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). #define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. #define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. #define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. #define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.

/**

• Stepper Drivers
• These settings allow Marlin to tune stepper driver timing and enable advanced options for
• stepper drivers that support them. You may also override timing options in Configuration_adv.h.
• A4988 is assumed for unspecified drivers.
• Options: A4988, A5984, DRV8825, LV8729, L6470, L6474, POWERSTEP01,

•      TB6560, TB6600, TMC2100,
  

•      TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
  

•      TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
  

•      TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
  

•      TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  

• :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] */ #define X_DRIVER_TYPE TMC2208 #define Y_DRIVER_TYPE TMC2208 #define Z_DRIVER_TYPE TMC2208 //#define X2_DRIVER_TYPE A4988 //#define Y2_DRIVER_TYPE A4988 //#define Z2_DRIVER_TYPE A4988 //#define Z3_DRIVER_TYPE A4988 //#define Z4_DRIVER_TYPE A4988 #define E0_DRIVER_TYPE TMC2208 //#define E1_DRIVER_TYPE A4988 //#define E2_DRIVER_TYPE A4988 //#define E3_DRIVER_TYPE A4988 //#define E4_DRIVER_TYPE A4988 //#define E5_DRIVER_TYPE A4988 //#define E6_DRIVER_TYPE A4988 //#define E7_DRIVER_TYPE A4988

// Enable this feature if all enabled endstop pins are interrupt-capable. // This will remove the need to poll the interrupt pins, saving many CPU cycles. //#define ENDSTOP_INTERRUPTS_FEATURE

/**

• Endstop Noise Threshold
• Enable if your probe or endstops falsely trigger due to noise.
• • Higher values may affect repeatability or accuracy of some bed probes.
• • To fix noise install a 100nF ceramic capacitor inline with the switch.
• • This feature is not required for common micro-switches mounted on PCBs
• based on the Makerbot design, which already have the 100nF capacitor.
• :[2,3,4,5,6,7] */ //#define ENDSTOP_NOISE_THRESHOLD 2

//============================================================================= //============================== Movement Settings ============================ //============================================================================= // @section motion

/**

• Default Settings
• These settings can be reset by M502
• Note that if EEPROM is enabled, saved values will override these. */

/**

• With this option each E stepper can have its own factors for the
• following movement settings. If fewer factors are given than the
• total number of extruders, the last value applies to the rest. */ //#define DISTINCT_E_FACTORS

/**

• Default Axis Steps Per Unit (steps/mm)
• Override with M92

•                                  X, Y, Z, E0 [, E1[, E2...]]
  

*/ #define DEFAULT_AXIS_STEPS_PER_UNIT { 79.80, 79.4, 399.2, 93 }

/**

• Default Max Feed Rate (mm/s)
• Override with M203

•                                  X, Y, Z, E0 [, E1[, E2...]]
  

*/ #define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 }

//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2 #if ENABLED(LIMITED_MAX_FR_EDITING) #define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits #endif

/**

• Default Max Acceleration (change/s) change = mm/s
• (Maximum start speed for accelerated moves)
• Override with M201

•                                  X, Y, Z, E0 [, E1[, E2...]]
  

*/ #define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 }

//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2 #if ENABLED(LIMITED_MAX_ACCEL_EDITING) #define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits #endif

/**

• Default Acceleration (change/s) change = mm/s
• Override with M204
• M204 P Acceleration
• M204 R Retract Acceleration
• M204 T Travel Acceleration */ #define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves #define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts #define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves

/**

• Default Jerk limits (mm/s)
• Override with M205 X Y Z E
• "Jerk" specifies the minimum speed change that requires acceleration.
• When changing speed and direction, if the difference is less than the
• value set here, it may happen instantaneously. */ //#define CLASSIC_JERK #if ENABLED(CLASSIC_JERK) #define DEFAULT_XJERK 10.0 #define DEFAULT_YJERK 10.0 #define DEFAULT_ZJERK 0.3

//#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2 #if ENABLED(LIMITED_JERK_EDITING) #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits #endif #endif

#define DEFAULT_EJERK 5.0 // May be used by Linear Advance

/**

• Junction Deviation Factor
• See:
• https://reprap.org/forum/read.php?1,739819
• http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html */ #if DISABLED(CLASSIC_JERK) #define JUNCTION_DEVIATION_MM 0.08 // (mm) Distance from real junction edge #endif

/**

• S-Curve Acceleration
• This option eliminates vibration during printing by fitting a Bézier
• curve to move acceleration, producing much smoother direction changes.
• See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained */ //#define S_CURVE_ACCELERATION

//=========================================================================== //============================= Z Probe Options ============================= //=========================================================================== // @section probes

// // See http://marlinfw.org/docs/configuration/probes.html //

/**

• Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
• Enable this option for a probe connected to the Z Min endstop pin. */ #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN

/**

• Z_MIN_PROBE_PIN
• Define this pin if the probe is not connected to Z_MIN_PIN.
• If not defined the default pin for the selected MOTHERBOARD
• will be used. Most of the time the default is what you want.
• • The simplest option is to use a free endstop connector.
• • Use 5V for powered (usually inductive) sensors.
• • RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
• • For simple switches connect...

•  - normally-closed switches to GND and D32.
  

•  - normally-open switches to 5V and D32.
  

*/ //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default

/**

• Probe Type
• Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
• Activate one of these to use Auto Bed Leveling below. */

/**

• The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
• Use G29 repeatedly, adjusting the Z height at each point with movement commands
• or (with LCD_BED_LEVELING) the LCD controller. */ //#define PROBE_MANUALLY //#define MANUAL_PROBE_START_Z 0.2

/**

• A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
• (e.g., an inductive probe or a nozzle-based probe-switch.) */ //#define FIX_MOUNTED_PROBE

/**

• Use the nozzle as the probe, as with a conductive
• nozzle system or a piezo-electric smart effector. */ //#define NOZZLE_AS_PROBE

/**

• Z Servo Probe, such as an endstop switch on a rotating arm. */ //#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. //#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles

/**

• The BLTouch probe uses a Hall effect sensor and emulates a servo. */ #define BLTOUCH

/**

• Touch-MI Probe by hotends.fr
• This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed.
• By default, the magnet is assumed to be on the left and activated by a home. If the magnet is
• on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
• Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,

•            and a minimum Z_HOMING_HEIGHT of 10.
  

*/ //#define TOUCH_MI_PROBE #if ENABLED(TOUCH_MI_PROBE) #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu) #endif

// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) //#define SOLENOID_PROBE

// A sled-mounted probe like those designed by Charles Bell. //#define Z_PROBE_SLED //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

// A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice. //#define RACK_AND_PINION_PROBE #if ENABLED(RACK_AND_PINION_PROBE) #define Z_PROBE_DEPLOY_X X_MIN_POS #define Z_PROBE_RETRACT_X X_MAX_POS #endif

// // For Z_PROBE_ALLEN_KEY see the Delta example configurations. //

/**

• Z Probe to nozzle (X,Y) offset, relative to (0, 0).
• In the following example the X and Y offsets are both positive:
• #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }

• +-- BACK ---+
  

• |           |
  

• L | (+) P | R <-- probe (20,20)
• E | | I
• F | (-) N (+) | G <-- nozzle (10,10)
• T | | H

• |    (-)    | T
  

• |           |
  

• O-- FRONT --+
  

• (0,0)
• Specify a Probe position as { X, Y, Z } */ #define NOZZLE_TO_PROBE_OFFSET { -45, -13, -1.7 }

// Most probes should stay away from the edges of the bed, but // with NOZZLE_AS_PROBE this can be negative for a wider probing area. #define MIN_PROBE_EDGE 10

// X and Y axis travel speed (mm/m) between probes #define XY_PROBE_SPEED 10000

// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z

// Feedrate (mm/m) for the "accurate" probe of each point #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)

/**

• Multiple Probing
• You may get improved results by probing 2 or more times.
• With EXTRA_PROBING the more atypical reading(s) will be disregarded.
• A total of 2 does fast/slow probes with a weighted average.
• A total of 3 or more adds more slow probes, taking the average. */ #define MULTIPLE_PROBING 2 //#define EXTRA_PROBING 1

/**

• Z probes require clearance when deploying, stowing, and moving between
• probe points to avoid hitting the bed and other hardware.
• Servo-mounted probes require extra space for the arm to rotate.
• Inductive probes need space to keep from triggering early.
• Use these settings to specify the distance (mm) to raise the probe (or
• lower the bed). The values set here apply over and above any (negative)
• probe Z Offset set with NOZZLE_TO_PROBE_OFFSET, M851, or the LCD.
• Only integer values >= 1 are valid here.
• Example: M851 Z-5 with a CLEARANCE of 4 => 9mm from bed to nozzle.

• But: `M851 Z+1` with a CLEARANCE of 2  =>  2mm from bed to nozzle.
  

*/ #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes //#define Z_AFTER_PROBING 5 // Z position after probing is done

#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping

// For M851 give a range for adjusting the Z probe offset #define Z_PROBE_OFFSET_RANGE_MIN -20 #define Z_PROBE_OFFSET_RANGE_MAX 20

// Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST

// Before deploy/stow pause for user confirmation //#define PAUSE_BEFORE_DEPLOY_STOW #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW) //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe #endif

/**

• Enable one or more of the following if probing seems unreliable.
• Heaters and/or fans can be disabled during probing to minimize electrical
• noise. A delay can also be added to allow noise and vibration to settle.
• These options are most useful for the BLTouch probe, but may also improve
• readings with inductive probes and piezo sensors. */ //#define PROBING_HEATERS_OFF // Turn heaters off when probing #if ENABLED(PROBING_HEATERS_OFF) //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) #endif //#define PROBING_FANS_OFF // Turn fans off when probing //#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors

// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } #define X_ENABLE_ON 0 #define Y_ENABLE_ON 0 #define Z_ENABLE_ON 0 #define E_ENABLE_ON 0 // For all extruders

// Disables axis stepper immediately when it's not being used. // WARNING: When motors turn off there is a chance of losing position accuracy! #define DISABLE_X false #define DISABLE_Y false #define DISABLE_Z false

// Warn on display about possibly reduced accuracy //#define DISABLE_REDUCED_ACCURACY_WARNING

// @section extruder

#define DISABLE_E false // For all extruders //#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled

// @section machine

// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. #define INVERT_X_DIR true #define INVERT_Y_DIR true #define INVERT_Z_DIR true

// @section extruder

// For direct drive extruder v9 set to true, for geared extruder set to false. #define INVERT_E0_DIR true #define INVERT_E1_DIR false #define INVERT_E2_DIR false #define INVERT_E3_DIR false #define INVERT_E4_DIR false #define INVERT_E5_DIR false #define INVERT_E6_DIR false #define INVERT_E7_DIR false

// @section homing

//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed

//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.

//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... // Be sure you have this distance over your Z_MAX_POS in case.

// Direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1] #define X_HOME_DIR 1 #define Y_HOME_DIR 1 #define Z_HOME_DIR -1

// @section machine

// The size of the print bed #define X_BED_SIZE 220 #define Y_BED_SIZE 220

// Travel limits (mm) after homing, corresponding to endstop positions. #define X_MIN_POS 0 #define Y_MIN_POS 0 #define Z_MIN_POS 0 #define X_MAX_POS X_BED_SIZE #define Y_MAX_POS Y_BED_SIZE #define Z_MAX_POS 300

/**

• Software Endstops
• • Prevent moves outside the set machine bounds.
• • Individual axes can be disabled, if desired.
• • X and Y only apply to Cartesian robots.
• • Use 'M211' to set software endstops on/off or report current state */

// Min software endstops constrain movement within minimum coordinate bounds #define MIN_SOFTWARE_ENDSTOPS #if ENABLED(MIN_SOFTWARE_ENDSTOPS) #define MIN_SOFTWARE_ENDSTOP_X #define MIN_SOFTWARE_ENDSTOP_Y //#define MIN_SOFTWARE_ENDSTOP_Z #endif

// Max software endstops constrain movement within maximum coordinate bounds #define MAX_SOFTWARE_ENDSTOPS #if ENABLED(MAX_SOFTWARE_ENDSTOPS) #define MAX_SOFTWARE_ENDSTOP_X #define MAX_SOFTWARE_ENDSTOP_Y #define MAX_SOFTWARE_ENDSTOP_Z #endif

#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD #endif

/**

• Filament Runout Sensors
• Mechanical or opto endstops are used to check for the presence of filament.
• RAMPS-based boards use SERVO3_PIN for the first runout sensor.
• For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
• By default the firmware assumes HIGH=FILAMENT PRESENT. */ //#define FILAMENT_RUNOUT_SENSOR #if ENABLED(FILAMENT_RUNOUT_SENSOR) #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.

// Set one or more commands to execute on filament runout. // (After 'M412 H' Marlin will ask the host to handle the process.) #define FILAMENT_RUNOUT_SCRIPT "M600"

// After a runout is detected, continue printing this length of filament // before executing the runout script. Useful for a sensor at the end of // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. //#define FILAMENT_RUNOUT_DISTANCE_MM 25

#ifdef FILAMENT_RUNOUT_DISTANCE_MM // Enable this option to use an encoder disc that toggles the runout pin // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM // large enough to avoid false positives.) //#define FILAMENT_MOTION_SENSOR #endif #endif

//=========================================================================== //=============================== Bed Leveling ============================== //=========================================================================== // @section calibrate

/**

• Choose one of the options below to enable G29 Bed Leveling. The parameters
• and behavior of G29 will change depending on your selection.
• If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
• • AUTO_BED_LEVELING_3POINT
• Probe 3 arbitrary points on the bed (that aren't collinear)
• You specify the XY coordinates of all 3 points.
• The result is a single tilted plane. Best for a flat bed.
• • AUTO_BED_LEVELING_LINEAR
• Probe several points in a grid.
• You specify the rectangle and the density of sample points.
• The result is a single tilted plane. Best for a flat bed.
• • AUTO_BED_LEVELING_BILINEAR
• Probe several points in a grid.
• You specify the rectangle and the density of sample points.
• The result is a mesh, best for large or uneven beds.
• • AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
• A comprehensive bed leveling system combining the features and benefits
• of other systems. UBL also includes integrated Mesh Generation, Mesh
• Validation and Mesh Editing systems.
• • MESH_BED_LEVELING
• Probe a grid manually
• The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
• For machines without a probe, Mesh Bed Leveling provides a method to perform
• leveling in steps so you can manually adjust the Z height at each grid-point.
• With an LCD controller the process is guided step-by-step. */ //#define AUTO_BED_LEVELING_3POINT //#define AUTO_BED_LEVELING_LINEAR #define AUTO_BED_LEVELING_BILINEAR //#define AUTO_BED_LEVELING_UBL //#define MESH_BED_LEVELING

/**

• Normally G28 leaves leveling disabled on completion. Enable
• this option to have G28 restore the prior leveling state. */ //#define RESTORE_LEVELING_AFTER_G28

/**

• Enable detailed logging of G28, G29, M48, etc.
• Turn on with the command 'M111 S32'.
• NOTE: Requires a lot of PROGMEM! */ //#define DEBUG_LEVELING_FEATURE

#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL) // Gradually reduce leveling correction until a set height is reached, // at which point movement will be level to the machine's XY plane. // The height can be set with M420 Z #define ENABLE_LEVELING_FADE_HEIGHT

// For Cartesian machines, instead of dividing moves on mesh boundaries, // split up moves into short segments like a Delta. This follows the // contours of the bed more closely than edge-to-edge straight moves. #define SEGMENT_LEVELED_MOVES #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)

/**

• Enable the G26 Mesh Validation Pattern tool. */ //#define G26_MESH_VALIDATION #if ENABLED(G26_MESH_VALIDATION) #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool. #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool. #endif

#endif

#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)

// Set the number of grid points per dimension. #define GRID_MAX_POINTS_X 3 #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

// Probe along the Y axis, advancing X after each column //#define PROBE_Y_FIRST

#if ENABLED(AUTO_BED_LEVELING_BILINEAR)

// Beyond the probed grid, continue the implied tilt?
// Default is to maintain the height of the nearest edge.
//#define EXTRAPOLATE_BEYOND_GRID

//
// Experimental Subdivision of the grid by Catmull-Rom method.
// Synthesizes intermediate points to produce a more detailed mesh.
//
//#define ABL_BILINEAR_SUBDIVISION
#if ENABLED(ABL_BILINEAR_SUBDIVISION)
  // Number of subdivisions between probe points
  #define BILINEAR_SUBDIVISIONS 3
#endif

#endif

#elif ENABLED(AUTO_BED_LEVELING_UBL)

//=========================================================================== //========================= Unified Bed Leveling ============================ //===========================================================================

//#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh

#define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500

//#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used // as the Z-Height correction value.

#elif ENABLED(MESH_BED_LEVELING)

//=========================================================================== //=================================== Mesh ================================== //===========================================================================

#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS

#endif // BED_LEVELING

/**

• Add a bed leveling sub-menu for ABL or MBL.
• Include a guided procedure if manual probing is enabled. */ //#define LCD_BED_LEVELING

#if ENABLED(LCD_BED_LEVELING) #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment //#define MESH_EDIT_MENU // Add a menu to edit mesh points #endif

// Add a menu item to move between bed corners for manual bed adjustment //#define LEVEL_BED_CORNERS

#if ENABLED(LEVEL_BED_CORNERS) #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points //#define LEVEL_CENTER_TOO // Move to the center after the last corner #endif

/**

• Commands to execute at the end of G29 probing.
• Useful to retract or move the Z probe out of the way. */ //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"

// @section homing

// The center of the bed is at (X=0, Y=0) //#define BED_CENTER_AT_0_0

// Manually set the home position. Leave these undefined for automatic settings. // For DELTA this is the top-center of the Cartesian print volume. //#define MANUAL_X_HOME_POS 0 //#define MANUAL_Y_HOME_POS 0 //#define MANUAL_Z_HOME_POS 0

// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. // // With this feature enabled: // // - Allow Z homing only after X and Y homing AND stepper drivers still enabled. // - If stepper drivers time out, it will need X and Y homing again before Z homing. // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). // - Prevent Z homing when the Z probe is outside bed area. // #define Z_SAFE_HOMING

#if ENABLED(Z_SAFE_HOMING) #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). #endif

// Homing speeds (mm/m) #define HOMING_FEEDRATE_XY (2060) #define HOMING_FEEDRATE_Z (460)

// Validate that endstops are triggered on homing moves #define VALIDATE_HOMING_ENDSTOPS

// @section calibrate

/**

• Bed Skew Compensation
• This feature corrects for misalignment in the XYZ axes.
• Take the following steps to get the bed skew in the XY plane:
• 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
• 2. For XY_DIAG_AC measure the diagonal A to C
• 3. For XY_DIAG_BD measure the diagonal B to D
• 4. For XY_SIDE_AD measure the edge A to D
• Marlin automatically computes skew factors from these measurements.
• Skew factors may also be computed and set manually:
• • Compute AB : SQRT(2ACAC+2BDBD-4ADAD)/2
• • XY_SKEW_FACTOR : TAN(PI/2-ACOS((ACAC-ABAB-ADAD)/(2AB*AD)))
• If desired, follow the same procedure for XZ and YZ.
• Use these diagrams for reference:
• Y Z Z
• ^ B-------C ^ B-------C ^ B-------C
• | / / | / / | / /
• | / / | / / | / /
• | A-------D | A-------D | A-------D
• +-------------->X +-------------->X +-------------->Y

• XY_SKEW_FACTOR        XZ_SKEW_FACTOR        YZ_SKEW_FACTOR
  

*/ //#define SKEW_CORRECTION

#if ENABLED(SKEW_CORRECTION) // Input all length measurements here: #define XY_DIAG_AC 282.8427124746 #define XY_DIAG_BD 282.8427124746 #define XY_SIDE_AD 200

// Or, set the default skew factors directly here // to override the above measurements: #define XY_SKEW_FACTOR 0.0

//#define SKEW_CORRECTION_FOR_Z #if ENABLED(SKEW_CORRECTION_FOR_Z) #define XZ_DIAG_AC 282.8427124746 #define XZ_DIAG_BD 282.8427124746 #define YZ_DIAG_AC 282.8427124746 #define YZ_DIAG_BD 282.8427124746 #define YZ_SIDE_AD 200 #define XZ_SKEW_FACTOR 0.0 #define YZ_SKEW_FACTOR 0.0 #endif

// Enable this option for M852 to set skew at runtime //#define SKEW_CORRECTION_GCODE #endif

//============================================================================= //============================= Additional Features =========================== //=============================================================================

// @section extras

/**

• EEPROM
• Persistent storage to preserve configurable settings across reboots.
• M500 - Store settings to EEPROM.
• M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
• M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) */ #define EEPROM_SETTINGS // Persistent storage with M500 and M501 //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. #if ENABLED(EEPROM_SETTINGS) //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. #endif

// // Host Keepalive // // When enabled Marlin will send a busy status message to the host // every couple of seconds when it can't accept commands. // #define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages #define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. #define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating

// // G20/G21 Inch mode support // //#define INCH_MODE_SUPPORT

// // M149 Set temperature units support // //#define TEMPERATURE_UNITS_SUPPORT

// @section temperature

// Preheat Constants #define PREHEAT_1_LABEL "PLA" #define PREHEAT_1_TEMP_HOTEND 185 #define PREHEAT_1_TEMP_BED 45 #define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255

#define PREHEAT_2_LABEL "ABS" #define PREHEAT_2_TEMP_HOTEND 240 #define PREHEAT_2_TEMP_BED 0 #define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255

/**

• Nozzle Park
• Park the nozzle at the given XYZ position on idle or G27.
• The "P" parameter controls the action applied to the Z axis:
• P0 (Default) If Z is below park Z raise the nozzle.
• P1 Raise the nozzle always to Z-park height.
• P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. */ //#define NOZZLE_PARK_FEATURE

#if ENABLED(NOZZLE_PARK_FEATURE) // Specify a park position as { X, Y, Z_raise } #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) #endif

/**

• Clean Nozzle Feature -- EXPERIMENTAL
• Adds the G12 command to perform a nozzle cleaning process.
• Parameters:
• P Pattern
• S Strokes / Repetitions
• T Triangles (P1 only)
• Patterns:
• P0 Straight line (default). This process requires a sponge type material

•   at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
  

•   between the start / end points.
  

• P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the

•   number of zig-zag triangles to do. "S" defines the number of strokes.
  

•   Zig-zags are done in whichever is the narrower dimension.
  

•   For example, "G12 P1 S1 T3" will execute:
  

•      --
  

•     |  (X0, Y1) |     /\        /\        /\     | (X1, Y1)
  

•     |           |    /  \      /  \      /  \    |
  

•   A |           |   /    \    /    \    /    \   |
  

•     |           |  /      \  /      \  /      \  |
  

•     |  (X0, Y0) | /        \/        \/        \ | (X1, Y0)
  

•      --         +--------------------------------+
  

•                   |________|_________|_________|
  

•                       T1        T2        T3
  

• P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.

•   "R" specifies the radius. "S" specifies the stroke count.
  

•   Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
  

• Caveats: The ending Z should be the same as starting Z.
• Attention: EXPERIMENTAL. G-code arguments may change.

*/ //#define NOZZLE_CLEAN_FEATURE

#if ENABLED(NOZZLE_CLEAN_FEATURE) // Default number of pattern repetitions #define NOZZLE_CLEAN_STROKES 12

// Default number of triangles #define NOZZLE_CLEAN_TRIANGLES 3

// Specify positions for each tool as { { X, Y, Z }, { X, Y, Z } } // Dual hotend system may use { { -20, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }, { 420, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }} #define NOZZLE_CLEAN_START_POINT { { 30, 30, (Z_MIN_POS + 1) } } #define NOZZLE_CLEAN_END_POINT { { 100, 60, (Z_MIN_POS + 1) } }

// Circular pattern radius #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 // Circular pattern circle fragments number #define NOZZLE_CLEAN_CIRCLE_FN 10 // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT

// Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK

// Enable for a purge/clean station that's always at the gantry height (thus no Z move) //#define NOZZLE_CLEAN_NO_Z #endif

/**

• Print Job Timer
• Automatically start and stop the print job timer on M104/M109/M190.
• M104 (hotend, no wait) - high temp = none, low temp = stop timer
• M109 (hotend, wait) - high temp = start timer, low temp = stop timer
• M190 (bed, wait) - high temp = start timer, low temp = none
• The timer can also be controlled with the following commands:
• M75 - Start the print job timer
• M76 - Pause the print job timer
• M77 - Stop the print job timer */ #define PRINTJOB_TIMER_AUTOSTART

/**

• Print Counter
• Track statistical data such as:
• • Total print jobs
• • Total successful print jobs
• • Total failed print jobs
• • Total time printing
• View the current statistics with M78. */ //#define PRINTCOUNTER

//============================================================================= //============================= LCD and SD support ============================ //=============================================================================

// @section lcd

/**

• LCD LANGUAGE
• Select the language to display on the LCD. These languages are available:
• en, an, bg, ca, cz, da, de, el, el_gr, es, eu, fi, fr, gl, hr, it, jp_kana,
• ko_KR, nl, pl, pt, pt_br, ru, sk, tr, uk, vi, zh_CN, zh_TW, test
• :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el_gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp_kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt_br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'vi':'Vietnamese', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' } */ #define LCD_LANGUAGE en

/**

• LCD Character Set
• Note: This option is NOT applicable to Graphical Displays.
• All character-based LCDs provide ASCII plus one of these
• language extensions:
• • JAPANESE ... the most common
• • WESTERN ... with more accented characters
• • CYRILLIC ... for the Russian language
• To determine the language extension installed on your controller:
• • Compile and upload with LCD_LANGUAGE set to 'test'
• • Click the controller to view the LCD menu
• • The LCD will display Japanese, Western, or Cyrillic text
• See http://marlinfw.org/docs/development/lcd_language.html
• :['JAPANESE', 'WESTERN', 'CYRILLIC'] */ #define DISPLAY_CHARSET_HD44780 WESTERN

/**

• Info Screen Style (0:Classic, 1:Prusa)
• :[0:'Classic', 1:'Prusa'] */ #define LCD_INFO_SCREEN_STYLE 0

/**

• SD CARD
• SD Card support is disabled by default. If your controller has an SD slot,
• you must uncomment the following option or it won't work.

*/ #define SDSUPPORT

/**

• SD CARD: SPI SPEED
• Enable one of the following items for a slower SPI transfer speed.
• This may be required to resolve "volume init" errors. */ //#define SPI_SPEED SPI_HALF_SPEED //#define SPI_SPEED SPI_QUARTER_SPEED //#define SPI_SPEED SPI_EIGHTH_SPEED

/**

• SD CARD: ENABLE CRC
• Use CRC checks and retries on the SD communication. */ //#define SD_CHECK_AND_RETRY

/**

• LCD Menu Items
• Disable all menus and only display the Status Screen, or
• just remove some extraneous menu items to recover space. */ //#define NO_LCD_MENUS //#define SLIM_LCD_MENUS

// // ENCODER SETTINGS // // This option overrides the default number of encoder pulses needed to // produce one step. Should be increased for high-resolution encoders. // //#define ENCODER_PULSES_PER_STEP 4

// // Use this option to override the number of step signals required to // move between next/prev menu items. // //#

[Fabriglas]

Just setting up my skr 1.4 turbo with btt 3.5 e3 TFT ..and see the Pi may not be able to hook up for octoprint... any advice?