config
config copied to clipboard
betaflight
Add HGLRC_H743_PRO board
Checklist (✓/✕, or y/n)
- [ ] passed Betaflight team's schematics review
- [ ] passed hardware samples testing
- [ ] follows guidelines
- [ ] follows connector standards
- [ ] flight tested
- [ ] comments/issues resolved
Summary by CodeRabbit
- New Features
- Added support for the HGLRC_H743_PRO flight controller (STM32H743).
- Enables accelerometer, gyro (selectable), barometer, OSD, onboard flash Blackbox logging, and inverted beeper option.
- Supports up to 8 motor outputs, multiple UART/I2C/SPI interfaces, LEDs, servos, and ADC-based voltage/current sensing with default scaling.
- Includes predefined pin/timer mappings, DMA mappings, and user-configurable IO box labels.
Walkthrough
Adds a new public board configuration header configs/HGLRC_H743_PRO/config.h for the HGLRC_H743_PRO (STM32H743), declaring MCU/board/manufacturer IDs, enabled sensors/peripherals, comprehensive pin/timer/DMA mappings, ADC/meter defaults, PINIO/box settings, and related macros.
Changes
| Cohort / File(s) | Summary |
|---|---|
New HGLRC H743 PRO Board Configuration configs/HGLRC_H743_PRO/config.h |
New public board config: sets FC_TARGET_MCU, BOARD_NAME, MANUFACTURER_ID; enables sensors/peripherals (ACC, GYRO, BARO, MAX7456, FLASH); defines SPI/I2C/UART pins & instances, CS/EXTI/CLKIN pins; motor/servo/LED/beeper pins; ADC VBAT/CURRENT pins; TIMER_PIN_MAPPING; DMA option macros; BARO/MAG I2C instances; default blackbox/current/voltage meter settings and scale; PINIO/box/user mappings; BEEPER_INVERTED and DEFAULT_GYRO_TO_USE. |
Estimated code review effort
🎯 3 (Moderate) | ⏱️ ~20 minutes
- Verify pin mappings against the HGLRC H743 PRO schematic/PCB.
- Confirm SPI/I2C/UART instances, CS/EXTI/CLKIN and
TIMER_PIN_MAPPINGsuitability for STM32H743. - Validate DMA option indices and ADC/voltage scale values.
Possibly related PRs
- betaflight/config#793 — Another STM32H743 board config header adding the same set of exported macros and mappings.
- betaflight/config#900 — Adds a similar STM32H743 board configuration header with largely identical public macros and pin/timer mappings.
- betaflight/config#927 — Adds a near-identical STM32H743 board config header defining matching MCU, sensor flags, and pin mappings.
Suggested labels
Awaiting prototype samples
Suggested reviewers
- haslinghuis
- ot0tot
- nerdCopter
Pre-merge checks and finishing touches
❌ Failed checks (1 warning)
| Check name | Status | Explanation | Resolution |
|---|---|---|---|
| Description check | ⚠️ Warning | The pull request description contains only the checklist section but omits all mandatory sections including hardware compliance requirements, design guidelines, and detailed change descriptions required by the template. | Replace the minimal checklist with the full template content, including hardware compliance requirements, design guidelines adherence statements, and a detailed description of changes being introduced before merging. |
✅ Passed checks (2 passed)
| Check name | Status | Explanation |
|---|---|---|
| Title check | ✅ Passed | The title 'Add HGLRC_H743_PRO board' is concise, clear, and directly describes the main change—introducing a new board configuration file for the HGLRC_H743_PRO flight controller. |
| Docstring Coverage | ✅ Passed | No functions found in the changed files to evaluate docstring coverage. Skipping docstring coverage check. |
✨ Finishing touches
- [ ] 📝 Generate docstrings
🧪 Generate unit tests (beta)
- [ ] Create PR with unit tests
- [ ] Post copyable unit tests in a comment
📜 Recent review details
Configuration used: Path: .coderabbit.yaml
Review profile: CHILL
Plan: Pro
📥 Commits
Reviewing files that changed from the base of the PR and between 846e8cf07758b220fdd1e69714b2983e14e3206a and 456ecf42422e24f15eb492f3e3737728acc2ae8e.
📒 Files selected for processing (1)
configs/HGLRC_H743_PRO/config.h(1 hunks)
🧰 Additional context used
🧠 Learnings (25)
📓 Common learnings
Learnt from: ot0tot
Repo: betaflight/config PR: 0
File: :0-0
Timestamp: 2025-07-03T04:33:57.480Z
Learning: Always verify that the BOARD_NAME define in each config.h matches the directory name it resides in (e.g., configs/AXISFLYINGF7AIO/config.h must have #define BOARD_NAME AXISFLYINGF7AIO). This check is required for all Betaflight board configuration reviews.
Learnt from: haslinghuis
Repo: betaflight/config PR: 835
File: configs/HDZERO_HALO_MPU6000/config.h:44-56
Timestamp: 2025-07-14T16:16:56.822Z
Learning: For Betaflight board configurations of boards already in production, pin assignments in config.h files reflect the actual hardware design and cannot be changed, even if they present potential conflicts with debug interfaces. The configuration must match the physical board layout, not ideal software design preferences.
Learnt from: ot0tot
Repo: betaflight/config PR: 0
File: :0-0
Timestamp: 2025-07-03T04:33:57.480Z
Learning: Always verify that the `BOARD_NAME` define in config.h files exactly matches the directory name where the config file is located. For example, if the config file is in configs/AXISFLYINGF7AIO/config.h, then the BOARD_NAME should be defined as "AXISFLYINGF7AIO". This ensures proper board identification and configuration loading in Betaflight.
Learnt from: haslinghuis
Repo: betaflight/config PR: 879
File: configs/AIRBOTSUPERF4V2/config.h:42-45
Timestamp: 2025-08-22T17:08:23.283Z
Learning: In Betaflight board configurations, OSD feature flags like USE_OSD_SD (analog/MAX7456) and USE_OSD_HD (digital/MSP DisplayPort) are typically defined at build time by the build system, not in the individual board config.h files. Board configs can conditionally define OSD-related settings based on these build-time flags.
Learnt from: haslinghuis
Repo: betaflight/config PR: 792
File: configs/BEEROTORF4/config.h:30-30
Timestamp: 2025-05-28T15:42:05.402Z
Learning: The DEFAULT_GYRO_ENABLED macro with both gyros enabled (GYRO_MASK(0) | GYRO_MASK(1)) should only be added to board configurations that have DEFAULT_GYRO_TO_USE set to GYRO_CONFIG_USE_GYRO_BOTH. Boards without this setting should only get the GYRO_COUNT definition.
Learnt from: haslinghuis
Repo: betaflight/config PR: 792
File: configs/BEEROTORF4/config.h:30-30
Timestamp: 2025-05-28T15:42:05.402Z
Learning: The DEFAULT_GYRO_ENABLED macro with both gyros enabled (GYRO_MASK(0) | GYRO_MASK(1)) should only be added to board configurations that have DEFAULT_GYRO_TO_USE set to GYRO_CONFIG_USE_GYRO_BOTH. Boards without this setting should only get the GYRO_COUNT definition to specify the number of available gyros.
Learnt from: haslinghuis
Repo: betaflight/config PR: 814
File: configs/JHEF405PRO/config.h:109-109
Timestamp: 2025-06-08T22:02:28.961Z
Learning: The JHEF405PRO board does not actually use dual gyros despite having GYRO_2_SPI_INSTANCE defined in its configuration. It should not receive GYRO_COUNT or other dual-gyro related definitions since only the first gyro is supported.
Learnt from: osirisinferi
Repo: betaflight/config PR: 972
File: configs/AXISFLYING_H743PRO/config.h:98-98
Timestamp: 2025-12-03T20:50:01.374Z
Learning: In Betaflight board configurations, if PINIOx_BOX or PINIOx_CONFIG defines are present in a config.h file, the corresponding PINIOx_PIN define must also be present to specify the actual pin assignment. Each PINIO instance requires a pin definition before it can be configured or assigned to a box.
Learnt from: haslinghuis
Repo: betaflight/config PR: 0
File: :0-0
Timestamp: 2025-07-03T15:17:30.040Z
Learning: In Betaflight configurations, when a target name suggests dual IMUs (like JHEF7DUAL) but specific hardware variants only have one gyro available, the preferred solution is to use DEFAULT_GYRO_TO_USE macro to specify which gyro to use by default rather than pruning gyro defines or creating redundant configurations. This approach maintains compatibility when the same target is used by multiple hardware variants from the same manufacturer.
Learnt from: haslinghuis
Repo: betaflight/config PR: 881
File: configs/GEPRC_TAKER_H743MINI/config.h:86-99
Timestamp: 2025-09-01T19:58:52.049Z
Learning: For STM32H743 PB0 in Betaflight, there are three timer options: TIM1_CH2N, TIM3_CH3, and TIM8_CH2N. Only TIM3_CH3 (timer index 2) is suitable for GYRO_CLKIN as the other two are complementary (N) channels. This is confirmed in timer_stm32h7xx.c.
📚 Learning: 2025-07-14T16:16:56.822Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 835
File: configs/HDZERO_HALO_MPU6000/config.h:44-56
Timestamp: 2025-07-14T16:16:56.822Z
Learning: For Betaflight board configurations of boards already in production, pin assignments in config.h files reflect the actual hardware design and cannot be changed, even if they present potential conflicts with debug interfaces. The configuration must match the physical board layout, not ideal software design preferences.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-07-03T04:33:57.480Z
Learnt from: ot0tot
Repo: betaflight/config PR: 0
File: :0-0
Timestamp: 2025-07-03T04:33:57.480Z
Learning: Always verify that the BOARD_NAME define in each config.h matches the directory name it resides in (e.g., configs/AXISFLYINGF7AIO/config.h must have #define BOARD_NAME AXISFLYINGF7AIO). This check is required for all Betaflight board configuration reviews.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-07-03T04:33:57.480Z
Learnt from: ot0tot
Repo: betaflight/config PR: 0
File: :0-0
Timestamp: 2025-07-03T04:33:57.480Z
Learning: Always verify that the `BOARD_NAME` define in config.h files exactly matches the directory name where the config file is located. For example, if the config file is in configs/AXISFLYINGF7AIO/config.h, then the BOARD_NAME should be defined as "AXISFLYINGF7AIO". This ensures proper board identification and configuration loading in Betaflight.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-06-23T18:43:31.746Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 822
File: configs/AXISFLYINGH7MINI/config.h:29-37
Timestamp: 2025-06-23T18:43:31.746Z
Learning: In Betaflight configuration files, feature enablement macros like USE_MAG are build options that can be controlled at compile time, while hardware instance definitions like MAG_I2C_INSTANCE are predefined in board configurations to assist with hardware mapping when those features are enabled at build time.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-07-03T15:17:30.040Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 0
File: :0-0
Timestamp: 2025-07-03T15:17:30.040Z
Learning: In Betaflight configurations, when a target name suggests dual IMUs (like JHEF7DUAL) but specific hardware variants only have one gyro available, the preferred solution is to use DEFAULT_GYRO_TO_USE macro to specify which gyro to use by default rather than pruning gyro defines or creating redundant configurations. This approach maintains compatibility when the same target is used by multiple hardware variants from the same manufacturer.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-08-22T17:08:23.283Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 879
File: configs/AIRBOTSUPERF4V2/config.h:42-45
Timestamp: 2025-08-22T17:08:23.283Z
Learning: In Betaflight board configurations, OSD feature flags like USE_OSD_SD (analog/MAX7456) and USE_OSD_HD (digital/MSP DisplayPort) are typically defined at build time by the build system, not in the individual board config.h files. Board configs can conditionally define OSD-related settings based on these build-time flags.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-07-28T16:44:59.686Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 656
File: configs/IFLIGHT_F745_AIO/config.h:31-35
Timestamp: 2025-07-28T16:44:59.686Z
Learning: In Betaflight board configurations, when a board design uses the same physical gyro socket but different sensor variants across production batches (e.g., MPU6000 in older batches, ICM42688P in newer batches), the correct approach is to enable both sensor drivers (USE_GYRO_SPI_MPU6000 and USE_GYRO_SPI_ICM42688P) in the same configuration. This allows runtime auto-detection of which sensor is actually present without requiring separate board configurations for each hardware variant.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-12-03T20:45:27.890Z
Learnt from: osirisinferi
Repo: betaflight/config PR: 972
File: configs/AXISFLYING_H743PRO/config.h:0-0
Timestamp: 2025-12-03T20:45:27.890Z
Learning: In Betaflight board configurations, always verify that TIMER_PIN_MAP entries do not use the same pin macro name multiple times. Each physical pin should appear only once in the TIMER_PIN_MAP definitions. For example, GYRO_1_CLKIN_PIN and GYRO_2_CLKIN_PIN should each appear exactly once, not have GYRO_1_CLKIN_PIN appear twice. This is a blocking issue that must be resolved before approval.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-07-23T13:43:50.456Z
Learnt from: ot0tot
Repo: betaflight/config PR: 0
File: :0-0
Timestamp: 2025-07-23T13:43:50.456Z
Learning: For Betaflight board configuration reviews, always verify that serial port defines (like ESC_SENSOR_UART, MSP_UART, GPS_UART, etc.) use valid SERIAL_PORT identifiers that match those defined in the Betaflight codebase at src/main/io/serial.h. Common valid identifiers include SERIAL_PORT_USART1, SERIAL_PORT_USART2, SERIAL_PORT_USART3, SERIAL_PORT_UART4, SERIAL_PORT_UART5, etc. Invalid identifiers like SERIAL_PORT_UART3 (should be SERIAL_PORT_USART3) will cause build failures.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-08-28T20:45:36.652Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 888
File: configs/ZEX_ATHENA_MINI/config.h:0-0
Timestamp: 2025-08-28T20:45:36.652Z
Learning: In STM32H743 Betaflight configurations, PA15 maps to TIM2_CH1 (timer index 2) as defined in timer_stm32h7xx.c. When used for GYRO_CLKIN functionality, it's recommended to use the macro name GYRO_1_CLKIN_PIN in TIMER_PIN_MAPPING for consistency with other pin definitions.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-06-02T16:16:20.197Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 0
File: :0-0
Timestamp: 2025-06-02T16:16:20.197Z
Learning: In STM32F405-based flight controller configurations, timer pin mappings must be carefully analyzed for DMA stream conflicts, especially between motor timers, LED strip timers, and SPI DMA assignments. Changes to TIMER_PIN_MAPPING should include verification that all required peripherals (motors, LED strip, blackbox SPI) can coexist without DMA conflicts.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-07-14T15:41:14.364Z
Learnt from: ot0tot
Repo: betaflight/config PR: 834
File: configs/RADIOLINKF405/config.h:79-88
Timestamp: 2025-07-14T15:41:14.364Z
Learning: In STM32F405 configurations, PB1 typically maps to TIM3_CH4 and PC9 typically maps to TIM8_CH4. These are different timers and do not share DMA resources, so there is no conflict when both pins are used simultaneously (e.g., PB1 for LED_STRIP and PC9 for MOTOR4).
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-08-28T20:45:36.652Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 888
File: configs/ZEX_ATHENA_MINI/config.h:0-0
Timestamp: 2025-08-28T20:45:36.652Z
Learning: In STM32H743 Betaflight configurations, PB0 can use multiple timer options including TIM1_CH2N, TIM3_CH3, and TIM8_CH2N as defined in timer_stm32h7xx.c. For CAMERA_CONTROL_PIN assignments, TIM3_CH3 (timer index 3) is the appropriate choice.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-09-01T19:58:52.049Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 881
File: configs/GEPRC_TAKER_H743MINI/config.h:86-99
Timestamp: 2025-09-01T19:58:52.049Z
Learning: For STM32H743 in Betaflight, PB0 has multiple timer options but only timer index 2 provides a non-complementary output suitable for GYRO_CLKIN functionality. The other timer options for PB0 are N channels (complementary outputs) which are not appropriate for CLKIN usage.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-09-01T19:58:52.049Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 881
File: configs/GEPRC_TAKER_H743MINI/config.h:86-99
Timestamp: 2025-09-01T19:58:52.049Z
Learning: For STM32H743 PB0 in Betaflight, there are three timer options: TIM1_CH2N, TIM3_CH3, and TIM8_CH2N. Only TIM3_CH3 (timer index 2) is suitable for GYRO_CLKIN as the other two are complementary (N) channels. This is confirmed in timer_stm32h7xx.c.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-06-02T16:16:20.197Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 0
File: :0-0
Timestamp: 2025-06-02T16:16:20.197Z
Learning: For Betaflight configurations, blackbox logging via SPI3 and LED_STRIP functionality can be mutually exclusive due to DMA stream conflicts on STM32F4 targets. This hardware limitation should be identified during timer configuration reviews.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-05-31T17:01:39.423Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 798
File: configs/FURYF4OSD/config.h:88-88
Timestamp: 2025-05-31T17:01:39.423Z
Learning: For STM32F4xx platforms, PB1 pin timer definitions are:
1 = DEF_TIM(TIM1, CH3N, PB1, 0, 0)
2 = DEF_TIM(TIM3, CH4, PB1, 0, 0)
3 = DEF_TIM(TIM8, CH3N, PB1, 0, 0)
Timer instance 2 (TIM3, CH4) is the correct mapping for PB1 motor control on STM32F4xx platforms as defined in src/platform/STM32/timer_stm32f4xx.c
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-08-21T11:11:19.213Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 870
File: configs/ZEX_ATHENA_STD_PRO/config.h:54-55
Timestamp: 2025-08-21T11:11:19.213Z
Learning: For STM32H743 in Betaflight, UART4 can use PB8 (UART4_RX) and PB9 (UART4_TX) with GPIO_AF8_UART4, as confirmed in the official Betaflight codebase at src/platform/STM32/serial_uart_stm32h7xx.c. This is a valid pin mapping despite what some generic STM32 documentation might suggest.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-12-03T20:50:01.374Z
Learnt from: osirisinferi
Repo: betaflight/config PR: 972
File: configs/AXISFLYING_H743PRO/config.h:98-98
Timestamp: 2025-12-03T20:50:01.374Z
Learning: In Betaflight board configurations, if PINIOx_BOX or PINIOx_CONFIG defines are present in a config.h file, the corresponding PINIOx_PIN define must also be present to specify the actual pin assignment. Each PINIO instance requires a pin definition before it can be configured or assigned to a box.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-07-25T20:06:07.492Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 719
File: configs/SPEDIXG473/config.h:29-38
Timestamp: 2025-07-25T20:06:07.492Z
Learning: BMP280 and DPS310 barometer drivers in Betaflight do not require USE_I2C to be explicitly defined in board configurations. Many existing boards successfully use USE_BARO_BMP280 and USE_BARO_DPS310 without defining USE_I2C, indicating that the I2C dependency is handled automatically by the build system or these sensors support alternative communication methods.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-09-26T16:32:46.694Z
Learnt from: osirisinferi
Repo: betaflight/config PR: 0
File: :0-0
Timestamp: 2025-09-26T16:32:46.694Z
Learning: In Betaflight configurations, I2C pins used for barometer and magnetometer communication should not be reassigned to UART functions as this creates hardware conflicts.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-07-25T20:06:07.492Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 719
File: configs/SPEDIXG473/config.h:29-38
Timestamp: 2025-07-25T20:06:07.492Z
Learning: BMP280 and DPS310 barometer drivers in Betaflight do not require USE_I2C to be explicitly defined in board configurations. Out of 264 boards using these drivers, 259 (98%) work without USE_I2C defined, indicating that the I2C dependency is handled automatically by the build system.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-05-28T15:45:15.608Z
Learnt from: haslinghuis
Repo: betaflight/config PR: 792
File: configs/MERAKRCF722/config.h:32-32
Timestamp: 2025-05-28T15:45:15.608Z
Learning: The presence of GYRO_2_SPI_INSTANCE definition in a board config does not necessarily mean the board uses dual gyros. Some boards have GYRO_2_SPI_INSTANCE defined but it's not actually used, so they should not receive GYRO_COUNT or other dual-gyro related definitions. Only boards that actually utilize dual gyros should get these definitions.
Applied to files:
configs/HGLRC_H743_PRO/config.h
📚 Learning: 2025-08-20T02:54:58.596Z
Learnt from: ot0tot
Repo: betaflight/config PR: 872
File: configs/HGLRCH743/config.h:82-83
Timestamp: 2025-08-20T02:54:58.596Z
Learning: For Betaflight board configuration reviews, the definitive source for validating UART pin assignments is the serial_uart_{platform}.c file in the Betaflight codebase (e.g., serial_uart_stm32h7xx.c for STM32H7xx platforms), not generic MCU datasheets. These files contain the exact pin mappings that Betaflight supports for each UART peripheral.
Applied to files:
configs/HGLRC_H743_PRO/config.h
🔇 Additional comments (6)
configs/HGLRC_H743_PRO/config.h (6)
24-27: LGTM! Board name matches directory.The BOARD_NAME define correctly matches the directory name, ensuring proper board identification. Based on learnings, this is a required check for all Betaflight board configurations.
29-39: LGTM! Feature enables support runtime sensor detection.The dual gyro driver support (MPU6000 and ICM42688P) enables runtime auto-detection of the actual sensor present, which is a best practice for boards that may use different sensor variants across production batches. Based on learnings, this approach is correct.
63-75: LGTM! Comprehensive motor and peripheral pin definitions.The configuration provides 8 motor outputs suitable for octocopter configurations, plus 3 servo outputs and LED strip support.
97-100: LGTM! Standard ADC configuration for voltage and current monitoring.
130-138: LGTM! PINIO configuration is complete and correct.Both PINIO instances have the required pin definitions along with their box and config settings. PINIO1_CONFIG is correctly set to 1 (low by default to select cam 1), addressing a previous review comment. Based on learnings, each PINIO instance requires a PIN define before BOX/CONFIG can be used.
102-116: Verification of timer mappings required before approval.The review cannot be completed without seeing the actual pin definitions (MOTOR7_PIN, MOTOR8_PIN, GYRO_1_CLKIN_PIN values). The claim that "PD15 lacks DMA support" cannot be verified without confirming which physical pins are assigned. Additionally:
- Per learnings, verify that no pin macro name appears more than once in TIMER_PIN_MAP (each physical pin should map exactly once).
- GYRO_1_CLKIN_PIN on timer 1 with DMA -1 may conflict with MOTOR1-4, LED_STRIP, and SERVO assignments, all on timer 1. Verify this does not cause DMA stream conflicts.
- PC6 (if GYRO_1_CLKIN_PIN) maps to TIM3_CH1 (AF2) or TIM8_CH1 (AF3)—confirm the intended timer index.
Provide the pin definitions and verify DMA assignments before approval.
Thanks for using CodeRabbit! It's free for OSS, and your support helps us grow. If you like it, consider giving us a shout-out.
Comment @coderabbitai help to get the list of available commands and usage tips.
![coderabbitai[bot] avatar](https://avatars.githubusercontent.com/in/347564?v=4 "Published by a pub.dev verified publisher"){kind=small}