Unable to interact with the GPIO of Raspberry Pi 5

[eMUQI]

Description

Unable to interact with the GPIO of Raspberry Pi 5

Expected Behavior

Draw a dot on Processing, which blinks synchronously with the LED.

Current Behavior

/sys/class/gpio/export：Invalid argument
GPIO pin 17 does not seem to be available on your platform
RuntimeException: /sys/class/gpio/export: Invalid argument
RuntimeException: /sys/class/gpio/export: Invalid argument

Steps to Reproduce

1. Install Hardware I/O
2. Run the code

   import processing.io.*;
   int ledPin = 17;
   boolean state = true;
   
   void setup() {
       size(100, 100);
       frameRate(2); //set frame rate
       GPIO.pinMode(ledPin, GPIO.OUTPUT); //set the ledPin to output mode
   }
   
   void draw() {
       state = !state;
       if (state==true) {
           GPIO.digitalWrite(ledPin, GPIO.LOW); //led on
           fill(255, 0, 0); //set the fill color of led on
       } else {
           GPIO.digitalWrite(ledPin, GPIO.HIGH); //led off
           fill(155); //set the fill color of led off
       }
       ellipse(width/2, height/2, width*0.75, height*0.75);
   }
   

3. error

Your Environment

• Processing version:
  • 4.3
• Operating System and OS version:
  • OS: Debian GNU/Linux 12 (bookworm) aarch64
  • Kernel: 6.1.0-rpi6-rpi-2712
• Other information:
  • Raspberry Pi 5 Model B Rev 1.0
  • CPU: BCM2835 (4) @ 2.400GHz

Possible Causes / Solutions

My suspicion is that it might be related to the introduction of the new southbridge chip, RP1, on the Raspberry Pi 5, which now handles the GPIOs and may have altered the access protocol.

Other

Also report at https://discourse.processing.org/t/issue-with-gpio-access-on-raspberry-pi-5-using-processing-4/43337

[Khushikela29]

Hii !! I think the issue is being resolved because the output after running the program is same as expected output

[eMUQI]

Hii !! I think the issue is being resolved because the output after running the program is same as expected output

Hello @Khushikela29, may I ask if you have run the aforementioned program on a Raspberry Pi 5? Today I tried again and still encountered the same error.

[falue]

I have the same issue (identical error messages) even with a rpi4.

I figure it has something to do with the fact that the rpi3 uses the "Sysfs Interface" for GPIO pins (which is phased out for a long time), and the rpi4 onwards "GPIO Character Device Interface". The Hardware I/O library seems to rely on the "Sysfs Interface"?

The folder /sys/class/gpio on the rpi 4 is almost empty, Output of ls -l /sys/class/gpio is:

xxx@raspberrypi:~ $ ls -l /sys/class/gpio
total 0
--w--w---- 1 root gpio 4096 Apr 23 17:04 export
lrwxrwxrwx 1 root gpio    0 Apr 23 17:04 gpiochip512 -> ../../devices/platform/soc/fe200000.gpio/gpio/gpiochip512
lrwxrwxrwx 1 root gpio    0 Apr 23 17:04 gpiochip570 -> ../../devices/platform/soc/soc:firmware/soc:firmware:gpio/gpio/gpiochip570
--w--w---- 1 root gpio 4096 Apr 23 17:04 unexport

Whereas output of the rpi 3 ls -l /sys/class/gpio is:

xxx@raspberrypi:~ $ ls -l /sys/class/gpio
total 0
--w--w---- 1 root gpio 4096 Apr 23 16:43 export
lrwxrwxrwx 1 root root    0 Apr 23 16:43 gpio10 -> ../../devices/platform/soc/3f200000.gpio/gpiochip0/gpio/gpio10
lrwxrwxrwx 1 root root    0 Apr 23 16:43 gpio11 -> ../../devices/platform/soc/3f200000.gpio/gpiochip0/gpio/gpio11
lrwxrwxrwx 1 root root    0 Apr 23 16:43 gpio13 -> ../../devices/platform/soc/3f200000.gpio/gpiochip0/gpio/gpio13
lrwxrwxrwx 1 root root    0 Apr 23 16:43 gpio17 -> ../../devices/platform/soc/3f200000.gpio/gpiochip0/gpio/gpio17
lrwxrwxrwx 1 root root    0 Apr 23 16:43 gpio19 -> ../../devices/platform/soc/3f200000.gpio/gpiochip0/gpio/gpio19
lrwxrwxrwx 1 root root    0 Apr 23 16:43 gpio26 -> ../../devices/platform/soc/3f200000.gpio/gpiochip0/gpio/gpio26
lrwxrwxrwx 1 root root    0 Apr 23 16:43 gpio27 -> ../../devices/platform/soc/3f200000.gpio/gpiochip0/gpio/gpio27
lrwxrwxrwx 1 root root    0 Apr 23 16:43 gpio5 -> ../../devices/platform/soc/3f200000.gpio/gpiochip0/gpio/gpio5
lrwxrwxrwx 1 root root    0 Apr 23 16:43 gpio6 -> ../../devices/platform/soc/3f200000.gpio/gpiochip0/gpio/gpio6
lrwxrwxrwx 1 root root    0 Apr 23 16:43 gpio9 -> ../../devices/platform/soc/3f200000.gpio/gpiochip0/gpio/gpio9
lrwxrwxrwx 1 root gpio    0 Apr 23 16:43 gpiochip0 -> ../../devices/platform/soc/3f200000.gpio/gpio/gpiochip0
lrwxrwxrwx 1 root gpio    0 Apr 23 16:43 gpiochip100 -> ../../devices/gpiochip1/gpio/gpiochip100
lrwxrwxrwx 1 root gpio    0 Apr 23 16:43 gpiochip504 -> ../../devices/platform/soc/soc:firmware/soc:firmware:expgpio/gpio/gpiochip504
--w--w---- 1 root gpio 4096 Apr 23 16:43 unexport

I might be totally off course. Not sure how anyone had used Processing 4 with GPIOs on a rpi4 or even rpi5, though. I might be missing something blatantly obvious to someone of course ;)

[JinbaoPeng]

In the latest systems (bookworm), processing is not available, so try going back to bullseye.