Translate Machine.h for MakerFR v2 XYYZ

[Guusggg]

This issue will automatically convert a Grbl_Esp32 "machine.h" file to FluidNC YAML format.

Change YOUR NAME in the title to some string that identifies your machine configuration.

Attach your Machine.h file here - but first change the .h extension to .txt because GitHub will not allow you to attach a file with a .h extension. Submit the issue, and after a few minutes, a new comment will appear with the FluidNC YAML file.

makerfr_v2_XYYZ.txt

[github-actions[bot]]

Dear Guusggg, we converted your machine header-file makerfr_v2_XYYZ.txt into a corresponding fluidNc yaml-file. Please copy the following content into your config.yaml file and upload the file to your esp32.

name: MakerFr GRBL 32 bits Board V2 XYYZ
board: unknown

kinematics:
  Cartesian:

stepping:
  engine: RMT
  idle_ms: 250
  dir_delay_us: 0
  pulse_us: 3
  disable_delay_us: 0

axes:
  shared_stepper_disable_pin: gpio.15
  x:
    steps_per_mm: 100.000
    max_rate_mm_per_min: 1000.000
    acceleration_mm_per_sec2: 200.000
    max_travel_mm: 300.000
    soft_limits: false
    motor0:
      limit_all_pin: gpio.36:low
      hard_limits: false
      stepstick:
        direction_pin: gpio.25
        step_pin: gpio.33
    motor1:
      null_motor:
  y:
    steps_per_mm: 100.000
    max_rate_mm_per_min: 1000.000
    acceleration_mm_per_sec2: 200.000
    max_travel_mm: 300.000
    soft_limits: false
    motor0:
      limit_all_pin: gpio.39:low
      hard_limits: false
      stepstick:
        direction_pin: gpio.27
        step_pin: gpio.26
    motor1:
      stepstick:
        direction_pin: gpio.32
        step_pin: gpio.13
  z:
    steps_per_mm: 100.000
    max_rate_mm_per_min: 1000.000
    acceleration_mm_per_sec2: 200.000
    max_travel_mm: 300.000
    soft_limits: false
    motor0:
      limit_all_pin: gpio.34:low
      hard_limits: false
      stepstick:
        direction_pin: gpio.12
        step_pin: gpio.14
    motor1:
      null_motor:
  a:
    steps_per_mm: 100.000
    max_rate_mm_per_min: 1000.000
    acceleration_mm_per_sec2: 200.000
    max_travel_mm: 300.000
    soft_limits: false
    motor0:
      limit_all_pin: gpio.35:low
      hard_limits: false
      null_motor:
    motor1:
      null_motor:

spi:
  miso_pin: gpio.19
  mosi_pin: gpio.23
  sck_pin: gpio.18

sdcard:
  cs_pin: gpio.5

control:
  reset_pin: gpio.4:low:pu
  feed_hold_pin: gpio.21:low:pu
  cycle_start_pin: gpio.0:low:pu

coolant:
  mist_pin: gpio.22
  delay_ms: 1000.000

probe:
  pin: gpio.16:pu
  check_mode_start: false

macros:
  startup_line0: 
  startup_line1: 
  macro0: 
  macro1: 
  macro2: 
  macro3: 

start:
  must_home: true
  check_limits: true
  deactivate_parking: false

user_outputs:
arc_tolerance_mm: 0.002
junction_deviation_mm: 0.010
verbose_errors: false
report_inches: false
enable_parking_override_control: false
use_line_numbers: false