bdring
Problem: The workpiece zero on the visualization panel of the Tablet tab is off to the left, so the left hand side of the track is obscured.
Controller Board
10V
Machine Description
N/a
Input Circuits
N/A
Configuration file
name: "WM16 Mill"
board: "ESP32 Dev Controller V4"
control:
safety_door_pin: gpio.27:high:pu
#
stepping:
engine: RMT
idle_ms: 250
dir_delay_us: 5
pulse_us: 2
disable_delay_us: 0
axes:
shared_stepper_disable_pin: NO_PIN
x:
steps_per_mm: 200
max_rate_mm_per_min: 2000
acceleration_mm_per_sec2: 25
max_travel_mm: 485
homing:
cycle: 2
mpos_mm: 5
positive_direction: false
motor0:
limit_neg_pin: gpio.35:high
pulloff_mm: 2
standard_stepper:
step_pin: gpio.13
direction_pin: gpio.14
y:
steps_per_mm: 200
max_rate_mm_per_min: 2000
acceleration_mm_per_sec2: 25
max_travel_mm: 150
homing:
cycle: 3
mpos_mm: 5
positive_direction: false
motor0:
limit_neg_pin: gpio.34:high
pulloff_mm: 2
standard_stepper:
step_pin: gpio.26
direction_pin: gpio.25
z:
steps_per_mm: 200
max_rate_mm_per_min: 2000
acceleration_mm_per_sec2: 25
max_travel_mm: 300
homing:
cycle: 1
mpos_mm: 5
positive_direction: true
motor0:
limit_pos_pin: gpio.22:high
pulloff_mm: 5
standard_stepper:
step_pin: gpio.33
direction_pin: gpio.32
spi:
miso_pin: gpio.19
mosi_pin: gpio.23
sck_pin: gpio.18
sdcard:
cs_pin: gpio.5
card_detect_pin: NO_PIN
coolant:
flood_pin: NO_PIN
mist_pin: NO_PIN
probe:
pin: gpio.21:low:pu
PWM:
pwm_hz: 5000
output_pin: gpio.15
enable_pin: NO_PIN
direction_pin: NO_PIN
disable_with_s0: false
s0_with_disable: true
spinup_ms: 0
spindown_ms: 0
tool_num: 0
speed_map: 0=0% 2500=100%
Startup Messages
--- FluidTerm v1.2.0 on /dev/ttyUSB0 115200,8,N,1 ---
--- Quit: Ctrl+] or Ctrl+Q | Upload: Ctrl+U | Reset: Ctrl+R | ClearScreen: Ctrl+W ---
Resetting MCU
ets Jul 29 2019 12:21:46
rst:0x1 (POWERON_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0030,len:1184
load:0x40078000,len:13220
ho 0 tail 12 room 4
load:0x40080400,len:3028
entry 0x400805e4
[MSG:INFO: FluidNC v3.7.1]
[MSG:INFO: Compiled with ESP32 SDK:v4.4.4]
[MSG:INFO: Local filesystem type is littlefs]
[MSG:INFO: Configuration file:config_nolimit.yaml]
[MSG:INFO: Machine WM16 Mill]
[MSG:INFO: Board ESP32 Dev Controller V4]
[MSG:INFO: SPI SCK:gpio.18 MOSI:gpio.23 MISO:gpio.19]
[MSG:INFO: SD Card cs_pin:gpio.5 detect:NO_PIN freq:8000000]
[MSG:INFO: Stepping:RMT Pulse:2us Dsbl Delay:0us Dir Delay:5us Idle Delay:250ms]
[MSG:INFO: Axis count 3]
[MSG:INFO: Axis X (0.000,485.000)]
[MSG:INFO: Motor0]
[MSG:INFO: standard_stepper Step:gpio.13 Dir:gpio.14 Disable:NO_PIN]
[MSG:INFO: X Neg Limit gpio.32:low]
[MSG:INFO: Axis Y (0.000,160.000)]
[MSG:INFO: Motor0]
[MSG:INFO: standard_stepper Step:gpio.27 Dir:gpio.26 Disable:NO_PIN]
[MSG:INFO: Y Pos Limit gpio.35:low]
[MSG:INFO: Axis Z (-270.000,0.000)]
[MSG:INFO: Motor0]
[MSG:INFO: standard_stepper Step:gpio.25 Dir:gpio.33 Disable:NO_PIN]
[MSG:INFO: Z Pos Limit gpio.34:low]
[MSG:INFO: Kinematic system: Cartesian]
[MSG:INFO: 10V Spindle Ena:gpio.15:low Out:gpio.22 Dir:NO_PIN Fwd:gpio.21:low Rev:gpio.4:low Freq:5000Hz Period:8191]
[MSG:INFO: Using spindle 10V]
[MSG:INFO: Connecting to STA SSID:TP-Link_0E2F]
[MSG:INFO: Connecting.]
[MSG:INFO: Connecting..]
[MSG:INFO: Connecting...]
[MSG:INFO: Connected - IP is 192.168.1.132]
[MSG:INFO: WiFi on]
[MSG:INFO: Start mDNS with hostname:http://fluidnc.local/]
[MSG:INFO: SSDP Started]
[MSG:INFO: HTTP started on port 80]
[MSG:INFO: Telnet started on port 23]
Grbl 3.7 [FluidNC v3.7.1 (wifi) '$' for help]
User Interface Software
WebUI
What happened?
In the Tablet window/tab, load a GRBL file from SD card. In the visualisation panel, lower-right, the workpiece G54 zero point is offset to the left by about 25% of the panel in one isometric view, i.e. 1/4 way in from the left-hand side of the panel. The left-hand portion of the track is not visible. In another view, it is right down in the bottom left-hand corner.
Other Information
[fluidnc_visualization_panel.pdf](https://github.com/bdring/Fl
uidNC/files/11746741/fluidnc_visualization_panel.pdf)
Try the new WebUI from https://github.com/MitchBradley/ESP3D-WEBUI/blob/revamp/index.html.gz . It might fix this problem.
I had seen this consistently with the previous version of Web UI, where if you click on the preview while a job is in progress, it changes perspective and resets the origin (or something) such that the dot no longer followed the curve.
With the latest WebUI 530686b this appears to be fixed. I would suggest closing.
