bb-qq
Speed state not showing ds916 5gb RTL8157
Description of the problem
DS916 - 5GB RTL8157 - 5GB
Not showing a speed state on network status or via SSH - just shows blank - not sure if its causing any issues but speeds are a little unstable - copying files at 300mb then suddently dropping to 10-20mb
Tried running a ethtool on ssh and it just states "speed unknown"
Tried multiple reboots etc of both devices - the pc is getting a 5gb speed showing just not the USB Dongle on the synology nas
Connected to a RTL8157 pc dongle over cat6a
PC shows 5GB connection - synology shows blank on 2.19.2 version
Description of your products
- DS916+ Linux nas 3.10.108 #42962 SMP Mon Aug 19 15:13:15 CST 2024 x86_64 GNU/Linux synology_braswell_916+ -7.1 WAVLINK USB C Ethernet Adapter, 5Gbps USB3.0/USB C RJ45
Description of your environment
-ETHERNET Direct WAVLINK USB C - Both sides CAT6
Output of dmesg command
Output of lsusb command
|__usb1 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (xhci_hcd 0000:00:14.0) hub |__1-5 f400:f400:0100 00 2.00 480MBit/s 200mA 1IF (Synology DiskStation 6500645DB5E41693) |__usb2 1d6b:0003:0310 09 3.00 5000MBit/s 0mA 1IF (xhci_hcd 0000:00:14.0) hub |__usb3 1d6b:0002:0310 09 2.00 480MBit/s 0mA 1IF (Linux 3.10.108 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub |__usb4 1d6b:0003:0310 09 3.00 5000MBit/s 0mA 1IF (Linux 3.10.108 etxhci_hcd-170202 Etron xHCI Host Controller 0000:04:00.0) hub |__4-1 0bda:8157:3000 00 3.20 5000MBit/s 544mA 1IF (Realtek USB 10/100/1G/2.5G/5G LAN 0003000001)
Output of ifconfig -a command
admin@nas:~$ ifconfig -a
bond0 Link encap:Ethernet HWaddr 00:11:32:5D:39:C3
inet addr:192.168.0.56 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
RX packets:15504 errors:0 dropped:0 overruns:0 frame:0
TX packets:15378 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5205120 (4.9 MiB) TX bytes:7668848 (7.3 MiB)
eth0 Link encap:Ethernet HWaddr 00:11:32:5D:39:C3
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:12645 errors:0 dropped:0 overruns:0 frame:0
TX packets:10048 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4394017 (4.1 MiB) TX bytes:5626629 (5.3 MiB)
eth1 Link encap:Ethernet HWaddr 00:11:32:5D:39:C4
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:2859 errors:0 dropped:0 overruns:0 frame:0
TX packets:5330 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:811103 (792.0 KiB) TX bytes:2042219 (1.9 MiB)
eth2 Link encap:Ethernet HWaddr 80:3F:5D:FD:B5:08
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::823f:5dff:fefd:b508/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2481 errors:0 dropped:0 overruns:0 frame:0
TX packets:2296 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:233097 (227.6 KiB) TX bytes:627548 (612.8 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:1967 errors:0 dropped:0 overruns:0 frame:0
TX packets:1967 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:309610 (302.3 KiB) TX bytes:309610 (302.3 KiB)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:192.168.20.1 P-t-P:192.168.20.2 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:500
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
It is a known problem that link speeds are not displayed correctly. It is a display only issue and does not affect the actual communication.
I will attempt to fix it after I get the device.
Hi
Thanks i did notice after it was a logged bug - my issue is i cant tell if im hitting 2.5gbps or 5gbps negotiation. Not sure how else i can tell
My File copy speeds are always 270mb max which makes me think im hitting 2.5gbps
(4X4 SHR RAID 7200 DISCS)
if i can help with my device let me know if any SSH access can help you
Just to add i installed openSpeed test aswell
My speeds are 1658 Download /2450MBPS upload
It would suggest to me im negotiating at 2.5Gbps
The display issue where the link speed was not displayed correctly on the RTL8157 has been fixed in the latest release. Could you check actual link speed?