LilyGo-LoRa-Series

LilyGo-LoRa-Series copied to clipboard

T-Beam `E (141058) task_wdt: Task watchdog got triggered.` After `enqueuing for send` using Meshtastic Firmware

5

I have a set of T-Beam m8n devices with board revision `T22_V1.1 20210222` all have been flashed to Meshtastic `2.3.4.ea61808 Beta` with the fully erase option I have one of...

JCBuck

https://github.com/Xinyuan-LilyGO/LilyGo-LoRa-Series/assets/104589489/99293511-a4d7-4280-902b-2e51358cc181 Board: V1.2 T3-S3 2.4gHz Lora with PA This SMD component is getting really hot whilst charging, up to 95°C within seconds. I don't want to risk loosing this board...

Vincent-NB

How to put LoRa32 V2.1_1.6 in boot mode for flashing

8

Hello, I tried finding instructions for putting LoRa32 V2.1_1.6 in boot mode so I can flash it with new firmware. I bought it recently with disaster radio on it but...

bennett-elder

Inconsistent pinout TTGO LoRa T3-S3

2

Hi, I'm trying to attach a BME280 sensor to my Lilygo TTGO LoRa T3-S3 that I just bought, but the pinout on the site is not correct.  As you...

BadCactus634

T-Beam V1.2 Mismatch Schematic to PCB - Header U12 Pin 1 5V is connected to USB VBUS0 instead of VSYS

3

The schematic for T-Beam V1.2 does not match the board (PCB). According to the schematic (https://github.com/Xinyuan-LilyGO/LilyGo-LoRa-Series/blob/master/schematic/LilyGo_TBeam_V1.2.pdf) pin 1 of connector U12 (labeled "5V" on the actual board) should be connected...

dj9pz

T3S3 v1.0 SX1280 DIO1 issue

10

I am attempting to run a [basic Lora transmitter example](https://github.com/StuartsProjects/SX12XX-LoRa/blob/master/examples/SX128x_examples/Basics/3_LoRa_Transmitter/3_LoRa_Transmitter.ino) from the [StuartsProjects/SX12XX-LoRa library](https://github.com/StuartsProjects/SX12XX-LoRa/tree/master). I know the LilyGo library has a basic transmitter example of it's own, which I've got...

TomsGitBits

Powering options

7

Hi! I cannot find somewhere authoritative where the different power options for the T-Beam v1.1 are described. That it can be powered using USB is obvious, but it is not...

nicklasb

T-Beam v1.2 GPS not working

2

SOC ESP32 Lora IC LILYGO LORA32 868/915MHz Description I am trying to figure out why the GPS module is not working. I already tested the GPS reset and test firmware...

Sailorspoon

Lily Go T-Beam Supreme connected wtih GSM GPRS

7

Is it possible to connect Lily GO T-BEAM Supreme with GPS GPRS such as SIM900A ? Can you suggest? Regards chantana

cchantra

Reconfigure 868z T-BeamSUPREME for 915 MHz

1

Can I reconfigure a 868MHz T-BeamSUPREME for 915 MHz? It seems the sx1262 supports 868MHz or 915MHz, so can I just flash the firmware (or change a constant) to change...

cwg523