Voron V0 Magnetic Tophat clips

[Coole-Guus]

• [x] The mod, firmware configuration or slicer profile is in the correct category folder. Printable mods go to printer_mods/, firmware configurations go to firmware_configurations/, slicer profiles go to slicer_profiles/. Create a subfolder with your name, and place the mods in a subfolder with a descriptive name within that folder, e.g.: /printer_mods/FHeilmann/flux_capacitor
• [x] Folders names MUST NOT contain spaces. If possible, make sure file names also do not contain any spaces.
• [x] For each mod, add a small README.md file to its folder with a short description of what the mod accomplishes. This readme can be used to add pictures, give assembly instructions or specify a bill of materials if the mod requires additional hardware.
• [x] The PR modifies the top-level README.md of the category folder adding the contribution to the table. Read the top part of the file for instructions on how to do this. Please preserve the alphabetical ordering while adding new rows. Make sure to fill out the compatibility matrix to indicate which versions of the Voron printer the submission is compatible with.
• [x] The mod/configuration/profile has been tested by the person submitting the mod and/or other Voron users. Make sure to add information about how the mod was tested below.
• [x] The mod is not merely a slight modification of an official Voron part, configuration or profile (i.e. an official Voron part with a few mm added or removed or a slicer profile which only modifies a few values). (When in doubt, contact one of the admins in the Voron discord before submitting the PR)
• [x] Submitted STLs are printable without support. (If the mod does not meet this criterion join the Voron discord and ask the other users for advice on how to modify the mod such that it does not require supports)
• [x] Submitted STL files are not corrupt. (This can be tested by opening the STL in PrusaSlicer and checking if mesh errors are reported.)
• [x] Submitted STL files are oriented and scaled properly for printing.
• [x] Submission includes a CAD file in the form of a .STEP or .SCAD file
• [x] Submitted firmware configs or slicer profiles contain no sensitive data (e.g. API keys).

Which mods/configurations/profiles are added by this PR?

This mod adds clips for magnetic alignment for the voron v0 tophat.

How was it tested?

physically printed and tested it. discord link to video: https://discord.com/channels/460117602945990666/635687829254701107/995345597949292544

Any background context you want to provide?

This mod is for low headroom spaces like putting your v0 in tight spaces where you cant fit a hinged solution. It could also help with hinged solutions to align the other half of the hat to the frame. Also pulls the hat towards the frame to create a better seal.

Screenshots (if appropriate)

See discord videos: https://discord.com/channels/460117602945990666/635687829254701107/995345597949292544

Further notes

[Coole-Guus]

thanks for looking at my pr, i am currently not near my printer and will try to add more detailed instructions + photos of the physical install tomorrow (24-7-2022).

[Coole-Guus]

When will this be merged?

[newphreak]

When will this be merged?

When the maintainers get around to it. They are mostly preoccupied with life currently. So be patient and it will be merged when they have a hot minute to look around here again. 👍

[cbc02009]

Sorry for the delay. Life has been very crazy the last couple months. Just a couple small changes and this should be good to go.

[Coole-Guus]

no worries that it had to wait. I also kinda forgot about the pull request lol. i fixed the issues but can't seem/ am not good enough at github to fix the merge conflict. can you help with that ?

[newphreak]

no worries that it had to wait. I also kinda forgot about the pull request lol. i fixed the issues but can't seem/ am not good enough at github to fix the merge conflict. can you help with that ?

https://docs.github.com/en/pull-requests/collaborating-with-pull-requests/working-with-forks/syncing-a-fork Go to your fork and just doublecheck that it's up to date

[FHeilmann]

Hi,

I want to thank you for your submission and want to personally apologize that your submission has not gotten the review it deserves. We are in the process to restructure the repo to streamline reviews and hopefully solve this issue in the future.

Unfortunately, this means that we will require you to resubmit the mod under the new system.

Please check here for details and instructions on how to proceed. If you have any questions, please reach out in the #voronuser_mods channel on the VoronDesign discord. If you have since moved on from this mod and don't want to resubmit, no further action is necessary from your side.

Bests,

Florian a.k.a. Haribro