issue between control for my gpu fans after update 249

[SamSupernoods]

If you are experiencing a crash Link the relevant/associated Windows EventViewer logs, and also FanControl's own log.txt.

Describe the bug [A clear and concise description of what the bug is. Screenshots are worth a thousand words. Hardware support requests do NOT count as a bug. See https://github.com/Rem0o/FanControl.Releases#issues-and-hardware-compatibility.]

it says this a discrepancy between the control and its target value is wrong ,this never happened before v249

Is there a log.txt file next to FanControl.exe with recent date entries? [Link it here]

Relevant hardware specs and setup [Laptops and most proprietary pre-built desktops are not supported.] mobo gigabyte arous 650 elite ax cpu 7800x3d gpu 7800xt

[Rem0o]

Can I see the fan curve ? Are you running the card between 1 and 30% anywhere in that curve?

See the AMD section: https://getfancontrol.com/docs/

[SamSupernoods]

here is the curve and i only mess with my adrenaline software after noticing this issue

[SamSupernoods]

here adrenaline settings

[SamSupernoods]

i should say at high temp the ? will not be there

[Rem0o]

See the red graph in adrenaline? There is a "floor" you can't put the graph lower than. This same floor value must be respected in FanControl.

[SamSupernoods]

But the floor is like 35 degrees and last time this never happened before

On Fri, 21 Nov 2025, 10:35 pm Rémi Mercier, @.***> wrote:

Rem0o left a comment (Rem0o/FanControl.Releases#3717) https://github.com/Rem0o/FanControl.Releases/issues/3717#issuecomment-3563283492

See the red graph in adrenaline? There is a "floor" you can't put the graph lower than. This same floor value must be respected in FanControl.

— Reply to this email directly, view it on GitHub https://github.com/Rem0o/FanControl.Releases/issues/3717#issuecomment-3563283492, or unsubscribe https://github.com/notifications/unsubscribe-auth/BADVVY5XOJTIEGIZX6OQS2D354PKNAVCNFSM6AAAAACMVLL3LSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZTKNRTGI4DGNBZGI . You are receiving this because you authored the thread.Message ID: @.***>

[Rem0o]

I meant the % value, not degree. FanControl can't override that floor. It's either 0, or like 33+ % or whatever your floor is.

[SamSupernoods]

Oh I mean the floor is set to like 35 percent , then how can I change or counter that so it use the fancontrol setting?

On Sat, 22 Nov 2025, 8:10 am Rémi Mercier, @.***> wrote:

Rem0o left a comment (Rem0o/FanControl.Releases#3717) https://github.com/Rem0o/FanControl.Releases/issues/3717#issuecomment-3565054481

I meant the % value, not degree. FanControl can't override that floor. It's either 0, or like 33+ % or whatever your floor is.

— Reply to this email directly, view it on GitHub https://github.com/Rem0o/FanControl.Releases/issues/3717#issuecomment-3565054481, or unsubscribe https://github.com/notifications/unsubscribe-auth/BADVVY2LCWRJF67YQQREKN3356SXPAVCNFSM6AAAAACMVLL3LSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZTKNRVGA2TINBYGE . You are receiving this because you authored the thread.Message ID: @.***>

[Rem0o]

With a curve shaped like this, which skips the 1-30 zone:

[SamSupernoods]

the min speed or temp?

[SamSupernoods]

[Rem0o]

Min speed in %

[SamSupernoods]

Hi can I ask if I turn on the zero rpm in adrenaline do u know wat temp does the fans will turn on? As i cannot do zero rpm on fan control

On Sun, 23 Nov 2025, 2:11 am Rémi Mercier, @.***> wrote:

Rem0o left a comment (Rem0o/FanControl.Releases#3717) https://github.com/Rem0o/FanControl.Releases/issues/3717#issuecomment-3566938402

Min speed in %

— Reply to this email directly, view it on GitHub https://github.com/Rem0o/FanControl.Releases/issues/3717#issuecomment-3566938402, or unsubscribe https://github.com/notifications/unsubscribe-auth/BADVVY6SJA5DSAH7JNK75ML36CROZAVCNFSM6AAAAACMVLL3LSVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZTKNRWHEZTQNBQGI . You are receiving this because you authored the thread.Message ID: @.***>