RIOT-OS
can: add CAN FD support to STM32G4 and native architecture
Contribution description
Until now RIOT supports CAN 2.0B. CAN FD increases the payload from 8 to 64 bytes and allows bit rate switching between headers (max. 1Mbits/s) and datas (max. 8Mbits/s).
RIOT supports some architecture featuring CAN FD but there was no drivers for it. That's the case of the STM32G4 family. Working completely differently than other STM32 featuring CAN 2.0B, I developed a new driver inspired of the existing can driver.
RIOT is aligned on SocketCAN data structures which already handles CAN FD frame, allowing to enable it for native architecture too.
Testing procedure
With nucleo-g431rb board:
# On the nucleo-g431rb
make -C tests/sys/conn_can/ BOARD=nucleo-g431rb -j flash
picocom -b 115200 --imap lfcrlf /dev/ttyACM0
# On a Raspberry Pi4
# Copy attached script test_fdcan.py and follow procedure in comments at the beginning of the script
# Then launch the script
chmod +x test_fdcan.py
./test_fdcan.py
The test_fdcan.py will send a frame with a payload of 64 bytes with the ID 0x77.
On the nucleo-g431rb, start receiving the frame by listening on thread 0, with no timeout:
> test_can recv 0 0 0 77
0: can_stm32_0 77 [40] 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
0: can_stm32_0 77 [40] 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
0: can_stm32_0 77 [40] 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
0: can_stm32_0 77 [40] 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
0: can_stm32_0 77 [40] 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
0: can_stm32_0 77 [40] 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
0: can_stm32_0 77 [40] 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
0: can_stm32_0 77 [40] 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
0: can_stm32_0 77 [40] 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
0: can_stm32_0 77 [40] 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
From the nucleo-g431rb, to send a CAN FD frame to the Pi4:
> test_can fdsend 0 10 0 1 2 3 4 5 6 7 8 9 A B C D E F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
Output on the Pi4:
$ ./test_fdcan.py
Python 3.9.2
Press CTL-C to exit
Message sent ID=0x77, Datas=[0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63]
Rx 0x40 bytes with ID=0x10 is_fd=True: 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xa 0xb 0xc 0xd 0xe 0xf 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x1e 0x1f 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2a 0x2b 0x2c 0x2d 0x2e 0x2f 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3a 0x3b 0x3c 0x3d 0x3e 0x3f
Message sent ID=0x77, Datas=[0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63]
Message sent ID=0x77, Datas=[0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63]
Message sent ID=0x77, Datas=[0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63]
Message sent ID=0x77, Datas=[0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63]
Message sent ID=0x77, Datas=[0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63]
Message sent ID=0x77, Datas=[0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63]
Message sent ID=0x77, Datas=[0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63]
Message sent ID=0x77, Datas=[0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63]
Rx 0x40 bytes with ID=0x10 is_fd=True: 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xa 0xb 0xc 0xd 0xe 0xf 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x1e 0x1f 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2a 0x2b 0x2c 0x2d 0x2e 0x2f 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3a 0x3b 0x3c 0x3d 0x3e 0x3f
Message sent ID=0x77, Datas=[0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63]
On the native architecture, you can reproduce the same test by setting up virtual can interface:
#!/bin/bash
# vcan0
sudo ip link delete vcan0
# To bring up CAN FD interface mtu size must increased to 72
sudo ip link add dev vcan0 type vcan bitrate 500000 dbitrate 1000000 fd on sample-point 0.875 mtu 72
sudo ip link set up vcan0
Murdock results
:heavy_check_mark: PASSED
974913596826d851e3ef493037cc7387c855359f fixup: configure also CONFIG_FDCAN_DEVICE_TRANSCEIVER_LOOP_DELAY for candev test
| Success | Failures | Total | Runtime |
|---|---|---|---|
| 10197 | 0 | 10197 | 19m:15s |
Artifacts
I noticed some problems around filtering, not sure where it comes from, I have to check. But just to inform it is not full ready yet.
I noticed some problems around filtering, not sure where it comes from, I have to check.
Any news on that? 🙂
I noticed some problems around filtering, not sure where it comes from, I have to check.
Any news on that? 🙂
Yes. Filters management got bugs, I had to rewrite it.
main problem was the management of standard and extended filters and also the default policy when no filters applied to the incoming frames. Non matching frames were accepted, instead of rejected.
It is fixed now.
I also modified the test to automatically add an "accept all frames" filter when no filters is specified:
In this screenshot, as you can see, first thread is receiving all CAN frames and second thread only those with ID 0x10000.
Displaying filters is working also:
> test_can get_filter 0
Filter 0: 0x0
Mask 0: 0x0
Filter 1: 0x10000
Mask 1: 0x1fffffff
When I close the receiving thread, filters are well removed:
> test_can close 0
0: recv terminated: ret=-113
> test_can get_filter 0
Filter 0: 0x10000
Mask 0: 0x1fffffff
"Reactivating" the receiving thread creates a filter again:
> test_can recv 0 0 0 77 78 79 80
> test_can get_filter 0
Filter 0: 0x77
Mask 0: 0x7ff
Filter 1: 0x78
Mask 1: 0x7ff
Filter 2: 0x79
Mask 2: 0x7ff
Filter 3: 0x80
Mask 3: 0x7ff
Filter 4: 0x10000
Mask 4: 0x1fffffff
Closing the receiving thread again deletes all its related filters:
> test_can close 0
0: recv terminated: ret=-113
> test_can get_filter 0
Filter 0: 0x10000
Mask 0: 0x1fffffff
An other concern is the mandatory hardware parameter that cannot have a default value CONFIG_FDCAN_DEVICE_TRANSCEIVER_LOOP_DELAY.
I force it to a fake value of 0 when in CI to avoid undefined macro when tests build (when RIOT_CI_BUILD is set to 1).
However, I did the setup of this variable through Kconfig also and I do not know if it the best way to do it.