mtk-openwrt-feeds
mtk-openwrt-feeds copied to clipboard
Published
20 hours ago •
Nossiac
Nossiac
MT7615 - incorrect 5ghz calibration?
We have a Xiaomi Mi router 3 Pro device here. The device includes 2xMT7615 cards, 1 per band. Compiled in:
- k4.4.116 (17.01 branch)
- mt7615 driver
- mtk luci plugin
- uci2dat
What we did:
- extracted eeprom per band from factory partition into /etc/wlan/*EEPROM{1,2}.bin respectively.
- copied stock SingleSKU.dat -> /etc/wireless/*sku.dat; but *sku-bf.dat is missing.
- copied mt7615e.eeprom.bin -> /lib/firmware/mt7615.eeprom.bin
With that setup 2.4ghz card works reasonably well, but 5ghz card seem to be severely miscalibrated and behaves on the border of reception.
@Nossiac what else may be missing? What else does the driver await?
Must add that absence or presence of /lib/firmware/mt7615.eeprom.bin doesn't have any effect on behavior.
Here's the log:
dmesg
root@LEDE:/# dmesg
[ 0.000000] Linux version 4.4.116 (admin@be) (gcc version 5.4.0 (LEDE GCC 5.4.0 r2993+848-b9a408c) ) #0 SMP Sun Feb 25 17:13:58 2018
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Xiaomi Mi Router 3 PRO
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 1c000000 @ 00000000 (usable)
[ 0.000000] memory: 04000000 @ 20000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem [mem 0x0000000010000000-0x0000000023ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000001bffffff]
[ 0.000000] node 0: [mem 0x0000000020000000-0x0000000023ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000023ffffff]
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] free_area_init_node: node 0, pgdat 8046d000, node_mem_map 81000000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65536 pages, LIFO batch:15
[ 0.000000] HighMem zone: 65536 pages, LIFO batch:15
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 10 pages/cpu @8148f000 s8544 r8192 d24224 u40960
[ 0.000000] pcpu-alloc: s8544 r8192 d24224 u40960 alloc=10*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130560
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=00000520
[ 0.000000] Readback ErrCtl register=00000520
[ 0.000000] Memory: 514028K/524288K available (3619K kernel code, 213K rwdata, 840K rodata, 244K init, 252K bss, 10260K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:256
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.007780] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.070402] pid_max: default: 32768 minimum: 301
[ 0.075098] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.081622] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.107606] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.107617] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.107631] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.107829] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.177340] Synchronize counters for CPU 1: done.
[ 0.201727] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.201734] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.201741] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.201821] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.267676] Synchronize counters for CPU 2: done.
[ 0.288854] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.288860] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.288867] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.288946] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.352848] Synchronize counters for CPU 3: done.
[ 0.357572] Brought up 4 CPUs
[ 0.364242] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.374029] futex hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.380373] pinctrl core: initialized pinctrl subsystem
[ 0.386152] NET: Registered protocol family 16
[ 0.396262] FPU Affinity set after 11720 emulations
[ 0.425893] pull PCIe RST: RALINK_RSTCTRL = 4000000
[ 0.730962] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.736009] ***** Xtal 40MHz *****
[ 0.739365] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.744460] Port 0 N_FTS = 1b105000
[ 0.747930] Port 1 N_FTS = 1b105000
[ 0.751372] Port 2 N_FTS = 1b102800
[ 1.905797] PCIE2 no card, disable it(RST&CLK)
[ 1.910154] -> 21007f2
[ 1.912555] PCIE0 enabled
[ 1.915146] PCIE1 enabled
[ 1.917743] PCI host bridge /pcie@1e140000 ranges:
[ 1.922522] MEM 0x0000000060000000..0x000000006fffffff
[ 1.927680] IO 0x000000001e160000..0x000000001e16ffff
[ 1.932881] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.974695] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.980380] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.985948] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.992682] PCI host bridge to bus 0000:00
[ 1.996715] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 2.003555] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 2.009403] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 2.016156] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 2.024043] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 2.024083] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 2.024101] pci 0000:00:00.0: reg 0x14: [mem 0x60200000-0x6020ffff]
[ 2.024167] pci 0000:00:00.0: supports D1
[ 2.024194] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 2.024439] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 2.024486] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 2.024511] pci 0000:00:01.0: reg 0x14: [mem 0x60210000-0x6021ffff]
[ 2.024559] pci 0000:00:01.0: supports D1
[ 2.024572] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 2.024985] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
[ 2.025055] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 2.025357] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 2.025569] pci 0000:02:00.0: [14c3:7615] type 00 class 0x000280
[ 2.025639] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 2.025923] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 2.025957] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 02
[ 2.026028] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 2.032561] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.039455] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.046033] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.052929] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 2.059686] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 2.066412] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
[ 2.073169] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff]
[ 2.079898] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 2.087169] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.092068] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.098840] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 2.106075] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.111005] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.117742] BAR0 at slot 0 = 0
[ 2.120743] bus=0x0, slot = 0x0
[ 2.123877] BAR0 at slot 1 = 0
[ 2.126880] bus=0x0, slot = 0x1
[ 2.129997] bus=0x1, slot = 0x0, irq=0x0
[ 2.133904] bus=0x2, slot = 0x1, irq=0x0
[ 2.139027] clocksource: Switched to clocksource GIC
[ 2.145761] NET: Registered protocol family 2
[ 2.150743] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.157629] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.164063] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.170426] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.176189] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.182645] NET: Registered protocol family 1
[ 2.186992] PCI: CLS 80 bytes, default 32
[ 2.418976] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 2.425367] Crashlog allocated RAM at address 0x3f00000
[ 2.437529] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.443445] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.455679] bounce: pool size: 64 pages
[ 2.459467] io scheduler noop registered
[ 2.463320] io scheduler deadline registered (default)
[ 2.468725] gpio-export gpio_export: 1 gpio(s) exported
[ 2.474157] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 2.481436] console [ttyS0] disabled
[ 2.484969] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 33, base_baud = 3125000) is a 16550A
[ 2.493967] console [ttyS0] enabled
[ 2.500834] bootconsole [early0] disabled
[ 2.509908] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.516957] Allocate 16 byte aligned buffer: 80503180
[ 2.522006] Enable NFI Clock
[ 2.524872] # MTK NAND # : Use HW ECC
[ 2.528530] Device found in MTK table, ID: c8da, EXT_ID: 909544
[ 2.534446] Support this Device in MTK table! c8da
[ 2.539454] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xda
[ 2.545774] nand: Unknown NAND 256MiB 3,3V 8-bit
[ 2.550381] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.557912] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.564349] Scanning device for bad blocks
[ 2.854955] 10 ofpart partitions found on MTD device MT7621-NAND
[ 2.860946] Creating 10 MTD partitions on "MT7621-NAND":
[ 2.866238] 0x000000000000-0x000000040000 : "Bootloader"
[ 2.872691] 0x000000040000-0x000000080000 : "Config"
[ 2.878627] 0x000000080000-0x0000000c0000 : "Bdata"
[ 2.884716] 0x0000000c0000-0x000000100000 : "Factory"
[ 2.890901] 0x000000100000-0x000000140000 : "crash"
[ 2.896779] 0x000000140000-0x0000001c0000 : "crash_syslog"
[ 2.903308] 0x0000001c0000-0x000000200000 : "reserved0"
[ 2.909668] 0x000000200000-0x000000600000 : "kernel_stock"
[ 2.916159] 0x000000600000-0x000000a00000 : "kernel"
[ 2.922214] 0x000000a00000-0x00000ff80000 : "ubi"
[ 2.928296] [mtk_nand] probe successfully!
[ 2.933167] Signature matched and data read!
[ 2.937415] load_fact_bbt success 2047
[ 2.941912] netif_napi_add() called with weight 128 on device eth%d
[ 3.011593] libphy: mdio: probed
[ 4.415022] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[ 4.421685] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 10
[ 4.430924] mt7621_wdt 1e000100.wdt: Initialized
[ 4.436783] NET: Registered protocol family 10
[ 4.442621] NET: Registered protocol family 17
[ 4.447113] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 4.459703] 8021q: 802.1Q VLAN Support v1.8
[ 4.466871] UBI: auto-attach mtd9
[ 4.470092] ubi0: attaching mtd9
[ 6.047637] mtk_soc_eth 1e100000.ethernet eth0: port 2 link up
[ 6.505309] mtk_soc_eth 1e100000.ethernet eth0: port 4 link up
[ 6.823433] ubi0: scanning is finished
[ 6.845620] ubi0: attached mtd9 (name "ubi", size 245 MiB)
[ 6.851128] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 6.857968] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 6.864738] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 6.871683] ubi0: good PEBs: 1964, bad PEBs: 0, corrupted PEBs: 0
[ 6.877745] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 6.884950] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 273634871
[ 6.893969] ubi0: available PEBs: 0, total reserved PEBs: 1964, PEBs reserved for bad PEB handling: 40
[ 6.903265] ubi0: background thread "ubi_bgt0d" started, PID 337
[ 6.905365] block ubiblock0_0: created from ubi0:0(rootfs)
[ 6.905375] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 6.905421] hctosys: unable to open rtc device (rtc0)
[ 6.932376] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 6.940083] Freeing unused kernel memory: 244K
[ 7.684489] init: Console is alive
[ 7.688089] init: - watchdog -
[ 8.743270] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 8.807927] usbcore: registered new interface driver usbfs
[ 8.813581] usbcore: registered new interface driver hub
[ 8.819083] usbcore: registered new device driver usb
[ 8.832640] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 8.837972] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 8.849186] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x00210010
[ 8.857646] xhci-mtk 1e1c0000.xhci: irq 29, io mem 0x1e1c0000
[ 8.864390] hub 1-0:1.0: USB hub found
[ 8.868213] hub 1-0:1.0: 2 ports detected
[ 8.872663] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 8.877964] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 8.885579] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 8.894490] hub 2-0:1.0: USB hub found
[ 8.898297] hub 2-0:1.0: 1 port detected
[ 8.904740] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 8.929276] init: - preinit -
[ 9.319135] usb 1-1: new high-speed USB device number 2 using xhci-mtk
[ 9.357142] random: procd: uninitialized urandom read (4 bytes read, 29 bits of entropy available)
[ 12.457123] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 423
[ 12.533585] UBIFS (ubi0:1): recovery needed
[ 12.742187] UBIFS (ubi0:1): recovery completed
[ 12.746736] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 12.754546] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 12.764428] UBIFS (ubi0:1): FS size: 237826048 bytes (226 MiB, 1873 LEBs), journal size 11935744 bytes (11 MiB, 94 LEBs)
[ 12.775255] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[ 12.781856] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID A7528018-18BF-46F2-93B5-45BD1594477A, small LPT model
[ 12.801953] mount_root: switching to ubifs overlay
[ 12.819947] urandom-seed: Seeding with /etc/urandom.seed
[ 12.962106] procd: - early -
[ 12.965080] procd: - watchdog -
[ 13.619149] procd: - watchdog -
[ 13.622549] procd: - ubus -
[ 13.745964] random: ubusd: uninitialized urandom read (4 bytes read, 51 bits of entropy available)
[ 13.804797] random: ubusd: uninitialized urandom read (4 bytes read, 51 bits of entropy available)
[ 13.814189] random: ubusd: uninitialized urandom read (4 bytes read, 51 bits of entropy available)
[ 13.823176] random: ubusd: uninitialized urandom read (4 bytes read, 51 bits of entropy available)
[ 13.832452] random: ubusd: uninitialized urandom read (4 bytes read, 51 bits of entropy available)
[ 13.841427] random: ubusd: uninitialized urandom read (4 bytes read, 51 bits of entropy available)
[ 13.850502] random: ubusd: uninitialized urandom read (4 bytes read, 51 bits of entropy available)
[ 13.859569] random: ubusd: uninitialized urandom read (4 bytes read, 51 bits of entropy available)
[ 13.868810] procd: - init -
[ 14.163565] kmodloader: loading kernel modules from /etc/modules.d/*
[ 14.173701] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.184824] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 14.192873] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 14.242180] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.253157] nf_conntrack version 0.5.0 (8035 buckets, 32140 max)
[ 14.369873] xt_time: kernel timezone is -0000
[ 14.380900] PPP generic driver version 2.4.2
[ 14.386326] NET: Registered protocol family 24
[ 14.393922] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.908899] random: jshn: uninitialized urandom read (4 bytes read, 77 bits of entropy available)
[ 19.117596] random: nonblocking pool is initialized
[ 19.987477] device eth0 entered promiscuous mode
[ 19.993791] device eth0.1 entered promiscuous mode
[ 20.003245] br-lan: port 1(eth0.1) entered forwarding state
[ 20.008876] br-lan: port 1(eth0.1) entered forwarding state
[ 21.999026] br-lan: port 1(eth0.1) entered forwarding state
[ 84.080273] mt7615: module license 'Proprietary' taints kernel.
[ 84.086187] Disabling lock debugging due to kernel taint
[ 84.174406] register mt_drv
[ 84.190245]
[ 84.190245]
[ 84.190245] === pAd = c0b81000, size = 3629168 ===
[ 84.190245]
[ 84.201210] <-- RTMPAllocAdapterBlock, Status=0
[ 84.205736] get_wdev_by_idx: invalid idx(0)
[ 84.209960] pAd->PciHif.CSRBaseAddress =0xc0a80000, csr_addr=0xc0a80000!
[ 84.216628] get_wdev_by_idx: invalid idx(0)
[ 84.220817] RTMPInitPCIeDevice():device_id=0x7615
[ 84.225498] DriverOwn()::Try to Clear FW Own...
[ 84.530053] DriverOwn()::Success to clear FW Own
[ 84.534658] mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615
[ 84.541780] mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001
[ 84.546812] RtmpChipOpsHook(493): Not support for HIF_MT yet! MACVersion=0x0
[ 84.553842] mt7615_init()-->
[ 84.556709] Use 1st ePAeLNA default bin.
[ 84.560633] Use 0st /etc/wlan/MT7615E_EEPROM1.bin default bin.
[ 84.566451] <--mt7615_init()
[ 84.569336] ChipOpsMCUHook
[ 84.577675] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[ 84.585441] cut_through_token_list_init(): 8f740f08,8f740f08
[ 84.591623] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[ 84.599372] cut_through_token_list_init(): 8f740f18,8f740f18
[ 84.605083] <-- RTMPAllocTxRxRingMemory, Status=0
[ 84.609787] get_wdev_by_idx: invalid idx(0)
[ 84.614128] get_wdev_by_idx: invalid idx(0)
[ 84.618442] get_wdev_by_idx: invalid idx(0)
[ 84.622632] get_wdev_by_idx: invalid idx(0)
[ 84.626800] get_wdev_by_idx: invalid idx(0)
[ 84.630982] get_wdev_by_idx: invalid idx(0)
[ 84.636516] get_wdev_by_idx: invalid idx(0)
[ 84.640931] pci probe count=1
[ 84.643344] get_wdev_by_idx: invalid idx(0)
[ 84.643353] get_wdev_by_idx: invalid idx(0)
[ 84.643359] get_wdev_by_idx: invalid idx(0)
[ 84.643364] get_wdev_by_idx: invalid idx(0)
[ 84.643369] get_wdev_by_idx: invalid idx(0)
[ 84.643373] get_wdev_by_idx: invalid idx(0)
[ 84.643451] get_wdev_by_idx: invalid idx(0)
[ 84.643459] DriverOwn()::Return since already in Driver Own...
[ 84.643465] ===============================
[ 84.643468] Current DevInfo Num: 0
[ 84.643471] ===============================
[ 84.643474] ===============================
[ 84.643477] Current BssInfo Num: 0
[ 84.643480] ===============================
[ 84.643484] ===============================
[ 84.643487] Current StaRec Num: 0
[ 84.643490] ===============================
[ 84.653878] DBDC_MODE is not enable! Not need to merge.
[ 84.734583]
[ 84.734583]
[ 84.734583] === pAd = c1001000, size = 3629168 ===
[ 84.734583]
[ 84.747046] <-- RTMPAllocAdapterBlock, Status=0
[ 84.751640] get_wdev_by_idx: invalid idx(0)
[ 84.755813] pAd->PciHif.CSRBaseAddress =0xc0f00000, csr_addr=0xc0f00000!
[ 84.762506] get_wdev_by_idx: invalid idx(0)
[ 84.766678] RTMPInitPCIeDevice():device_id=0x7615
[ 84.771381] DriverOwn()::Try to Clear FW Own...
[ 84.779542] multi-profile merge success, en:1,pf1_num:1,pf2_num:1,total:2
[ 84.788380] RT_CfgSetMacAddress : invalid length (0)
[ 84.794393] E2pAccessMode=2
[ 84.797789] SSID[0]=Xiaomi_6DF0_5G, EdcaIdx=0
[ 84.802440] SSID[1]=wifi-mt7615.1.2G, EdcaIdx=0
[ 84.807635] RTMPSetProfileParameters(): DBDC Mode=1
[ 84.814739] cfg_mode=14
[ 84.817176] cfg_mode=14
[ 84.819645] wmode_band_equal(): Band Equal!
[ 84.823821] cfg_mode=9
[ 84.826167] cfg_mode=9
[ 84.829850] [TxPower] BAND0: 100, BAND1: 100
[ 84.829850] [PERCENTAGEenable] BAND0: 1, BAND1: 1
[ 84.829850] APEdca0
[ 84.845022] Valid=1
[ 84.847113] APAifsn[0]=3
[ 84.849654] APAifsn[1]=7
[ 84.852177] APAifsn[2]=1
[ 84.854698] APAifsn[3]=1
[ 84.857231] APEdca1
[ 84.859646] Valid=1
[ 84.861737] APAifsn[0]=3
[ 84.864263] APAifsn[1]=7
[ 84.866787] APAifsn[2]=1
[ 84.869330] APAifsn[3]=1
[ 84.871863] APEdca2
[ 84.874336] APEdca3
[ 84.880919] BSSAifsn[0]=3
[ 84.883530] BSSAifsn[1]=7
[ 84.886137] BSSAifsn[2]=2
[ 84.888791] BSSAifsn[3]=2
[ 84.891749] BSSAifsn[0]=3
[ 84.894355] BSSAifsn[1]=7
[ 84.896963] BSSAifsn[2]=2
[ 84.899590] BSSAifsn[3]=2
[ 84.902713] APSDCapable[0]=0
[ 84.905580] APSDCapable[1]=0
[ 84.908448] default ApCliAPSDCapable[0]=0
[ 84.912458] default ApCliAPSDCapable[1]=0
[ 84.923650] [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0
[ 84.951273] SetWdevAuthMode:: Not support (AuthMode=none, len=4)
[ 84.985748] HT: Ext Channel = ABOVE
[ 84.989241] HT: Ext Channel = ABOVE
[ 84.994692] HT: greenap_cap = 0
[ 85.032351] EntryLifeCheck=1024
[ 85.036191] IcapMode = 0
[ 85.050006] WtcSetMaxStaNum: MaxStaNum:90, BssidNum:2, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:124
[ 85.060431] Top Init Done!
[ 85.063136] Use dev_alloc_skb
[ 85.067312] RX[0] DESC ae48a000 size = 8192
[ 85.072813] RX[1] DESC ae48c000 size = 8192
[ 85.078743] Hif Init Done!
[ 85.081468] ctl->txq = c0ef2c38
[ 85.084594] ctl->rxq = c0ef2c44
[ 85.087720] ctl->ackq = c0ef2c50
[ 85.090982] ctl->kickq = c0ef2c5c
[ 85.094289] ctl->tx_doneq = c0ef2c68
[ 85.097847] ctl->rx_doneq = c0ef2c74
[ 85.102846] mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615))
[ 85.108936] mt7615_fw_prepare(2752): MT7615_E3, USE E3 patch and ram code binary image
[ 85.116820] AndesMTLoadRomMethodFwDlRing(1036), cap->rom_patch_len(11150)
[ 85.123600] AndesRestartCheck: Current TOP_MISC2(0x1)
[ 85.128653] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
[ 85.135497] 20170304031443a
[ 85.138337]
[ 85.139838] platform =
[ 85.142272] ALPS
[ 85.144115] hw/sw version =
[ 85.146980] 8a108a10
[ 85.149202] patch version =
[ 85.152067] 00000010
[ 85.154370] Patch SEM Status=2
[ 85.157470] MtCmdPatchSemGet:(ret = 0)
[ 85.161260]
[ 85.161260] Patch is not ready && get semaphore success, SemStatus(2)
[ 85.162063] DriverOwn()::Success to clear FW Own
[ 85.162078] mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615
[ 85.162083] mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001
[ 85.162094] RtmpChipOpsHook(493): Not support for HIF_MT yet! MACVersion=0x0
[ 85.162098] mt7615_init()-->
[ 85.162104] Use 2nd ePAeLNA default bin.
[ 85.162109] Use 1st /etc/wlan/MT7615E_EEPROM2.bin default bin.
[ 85.162125] <--mt7615_init()
[ 85.162129] ChipOpsMCUHook
[ 85.167782] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[ 85.167789] cut_through_token_list_init(): 8e7f2d88,8e7f2d88
[ 85.168250] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[ 85.168254] cut_through_token_list_init(): 8e7f2d98,8e7f2d98
[ 85.168326] <-- RTMPAllocTxRxRingMemory, Status=0
[ 85.168335] get_wdev_by_idx: invalid idx(0)
[ 85.168338] get_wdev_by_idx: invalid idx(0)
[ 85.168715] get_wdev_by_idx: invalid idx(0)
[ 85.168722] get_wdev_by_idx: invalid idx(0)
[ 85.168734] get_wdev_by_idx: invalid idx(0)
[ 85.168737] get_wdev_by_idx: invalid idx(0)
[ 85.267708] EventGenericEventHandler: CMD Success
[ 85.272579] MtCmdAddressLenReq:(ret = 0)
[ 85.276632] MtCmdPatchFinishReq
[ 85.291068] EventGenericEventHandler: CMD Success
[ 85.295781] Send checksum req..
[ 85.299006] Patch SEM Status=3
[ 85.302075] MtCmdPatchSemGet:(ret = 0)
[ 85.305803]
[ 85.305803] Release patch semaphore, SemStatus(3)
[ 85.311999] AndesMTEraseRomPatch
[ 85.315213] WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0
[ 85.321311] AndesMTLoadFwMethodFwDlRing(810), cap->fw_len(459960)
[ 85.327387] Build Date:_201705121437
[ 85.331028] Build Date:_201705121437
[ 85.334638] AndesRestartCheck: Current TOP_MISC2(0x1)
[ 85.339697] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
[ 85.346610] EventGenericEventHandler: CMD Success
[ 85.351345] MtCmdAddressLenReq:(ret = 0)
[ 85.359831] EventGenericEventHandler: CMD Success
[ 85.364577] MtCmdAddressLenReq:(ret = 0)
[ 85.369057] MtCmdFwStartReq: override = 1, address = 540672
[ 85.374675] EventGenericEventHandler: CMD Success
[ 85.379413] Build Date:_201703141726
[ 85.383102] EventGenericEventHandler: CMD Success
[ 85.387812] MtCmdAddressLenReq:(ret = 0)
[ 85.392825] MtCmdFwStartReq: override = 4, address = 0
[ 85.463327] EventGenericEventHandler: CMD Success
[ 85.502190] WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0
[ 85.507909] MCU Init Done!
[ 85.510686] MtCmdSetRlmPorCal: (ret = 0)
[ 85.515465] efuse_probe: efuse = 10000212
[ 85.519491] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
[ 85.524869] RtmpEepromGetDefault::e2p_dafault=1
[ 85.529418] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
[ 85.536957] NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x0]
[ 85.542709] NICReadEEPROMParameters():Calling eeinit
[ 85.551092] NICReadEEPROMParameters: EEPROM 0x52 b300
[ 85.556823] NICReadEEPROMParameters: EEPROM 0x52 b300
[ 85.562577] Country Region from e2p = 1
[ 85.566397] mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4
[ 85.572565] mt7615_antenna_default_reset(): DBDC 2G TxPath = 2, 2G RxPath = 2
[ 85.579682] mt7615_antenna_default_reset(): DBDC 5G TxPath = 2, 2G RxPath = 2
[ 85.586796] rtmp_read_txpwr_from_eeprom(243): Don't Support this now!
[ 85.593221] RTMPReadTxPwrPerRate(1382): Don't Support this now!
[ 85.599134] RcRadioInit(): DbdcMode=1, ConcurrentBand=2
[ 85.604336] RcRadioInit(): pRadioCtrl=8f519450,Band=0,rfcap=1,channel=1,PhyMode=2
[ 85.611804] RcRadioInit(): pRadioCtrl=8f51953c,Band=1,rfcap=2,channel=36,PhyMode=1
[ 85.619554] MtCmdSetDbdcCtrl:(ret = 0)
[ 91.935478] Band Rf: 1, Phy Mode: 2
[ 91.938998] Band Rf: 2, Phy Mode: 1
[ 91.942468] AntCfgInit(2787): Not support for HIF_MT yet!
[ 91.947847] MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!!
[ 91.955319] MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!!
[ 91.963278] EEPROM Init Done!
[ 91.966238] mt_mac_init()-->
[ 91.969169] mt_mac_pse_init(2787): Don't Support this now!
[ 91.974638] mt7615_init_mac_cr()-->
[ 91.978119] mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c
[ 91.983357] mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c
[ 91.988579] MtAsicSetMacMaxLen(1313): Not finish Yet!
[ 91.993638] <--mt_mac_init()
[ 92.000443] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[ 92.007185] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[ 92.013991] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[ 92.020629] MAC Init Done!
[ 92.023329] MT7615BBPInit():BBP Initialization.....
[ 92.028185] Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2
[ 92.037229] Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0
[ 92.046267] MT7615BBPInit() todo
[ 92.049601] PHY Init Done!
[ 92.053919] tx_pwr_comp_init():NotSupportYet!
[ 92.058699] MtCmdSetMacTxRx:(ret = 0)
[ 92.062607] MtCmdSetMacTxRx:(ret = 0)
[ 92.066423] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/49, support 38 channels
[ 92.074813] WifiSysOpen(), wdev idx = 0
[ 92.078657] wdev_attr_update(): wdevId0 = 00:0c:43:26:60:00
[ 92.084522] MtCmdSetDbdcCtrl:(ret = 0)
[ 92.089028] ApAutoChannelAtBootUp----------------->
[ 92.093886] ApAutoChannelAtBootUp: AutoChannelBootup = 0, AutoChannelFlag = 0
[ 92.101005] ApAutoChannelAtBootUp<-----------------
[ 92.105862] Current Channel is 44. DfsZeroWaitSupport=0
[ 92.111101] MtAsicSetChBusyStat(865): Not support for HIF_MT yet!
[ 92.117163] MtAsicSetChBusyStat(865): Not support for HIF_MT yet!
[ 92.123274] [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0
[ 92.129113] [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
[ 92.135212] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=44
[ 92.143921] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/49, support 38 channels
[ 92.152348] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1
[ 92.152348] LinkToOmacIdx = 0, LinkToWdevType = 1
[ 92.169230] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196
[ 92.184730] MtCmdSetDbdcCtrl:(ret = 0)
[ 92.293360] [RadarStateCheck]Set into RD_NORMAL_MODE
[ 92.298306] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 0, BandIdx: 1
[ 92.304155] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 1
[ 92.310690] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 1
[ 92.316696] mt7615_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=44, HT-CentCh=46, VHT-CentCh=42
[ 92.324892] mt7615_apply_cal_data() : eeprom 0x52 bit 1 is 0, do runtime cal , skip RX reload
[ 92.333392] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload
[ 92.341902] MtCmdChannelSwitch: control_chl = 44,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 0
[ 92.351094] BW = 2,TXStream = 2, RXStream = 2, scan(0)
[ 92.468772] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 42(Prim=44, HT-CentCh=46, VHT-CentCh=42, BBP_BW=2)
[ 92.482218] [WrapDfsRadarDetectStart]: Band0Ch is 44[WrapDfsRadarDetectStart]: Band1Ch is 0LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY
[ 92.495590] MtAsicSetRalinkBurstMode(2618): Not support for HIF_MT yet!
[ 92.502276] MtAsicSetPiggyBack(802): Not support for HIF_MT yet!
[ 92.508261] MtAsicSetTxPreamble(2597): Not support for HIF_MT yet!
[ 92.514516] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2!
[ 92.521705] AndesLedEnhanceOP: Success!
[ 92.525594] Main bssid = 00:0c:43:26:60:00
[ 92.539361] AsicRadioOnOffCtrl(): DbdcIdx=1 RadioOn
[ 92.544527] MtCmdSetMacTxRx:(ret = 0)
[ 92.548271] MtCmdSetMacTxRx:(ret = 0)
[ 92.551984] fdb_enable()
[ 92.854406] MCS Set = ff ff 00 00 01
[ 92.857989] <==== mt_wifi_init, Status=0
[ 92.861952] MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1
[ 92.866998] MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 1
[ 92.876738] WtcSetMaxStaNum: MaxStaNum:90, BssidNum:2, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:124
[ 92.933734] red_is_enabled: set CR4/N9 RED Enable to 1.
[ 92.939039] cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2.
[ 92.945031] Correct apidx from 0 to 0 for WscUUIDInit
[ 92.950083] Generate UUID for apidx(0)
[ 92.953884] UUID: c0bb3530, len = 16
[ 92.957490] 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 00 0c 43 26 60 00
[ 92.964037]
[ 92.967544] get_wdev_by_idx: invalid idx(0)
[ 92.972043] pci probe count=2
[ 92.972682] device ra0 entered promiscuous mode
[ 92.972808] br-lan: port 2(ra0) entered forwarding state
[ 92.972846] br-lan: port 2(ra0) entered forwarding state
[ 92.979065] WifiSysOpen(), wdev idx = 1
[ 92.979086] wdev_attr_update(): wdevId1 = 02:0c:43:36:60:00
[ 92.979378] MtCmdSetDbdcCtrl:(ret = 0)
[ 92.980653] [PMF]APPMFInit:: apidx=1, MFPC=0, MFPR=0, SHA256=0
[ 92.980680] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=6
[ 92.980872] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/49, support 38 channels
[ 92.980984] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:126 for WDEV_TYPE:1
[ 92.980984] LinkToOmacIdx = 11, LinkToWdevType = 1
[ 92.981059] [RadarStateCheck]Set into RD_NORMAL_MODE
[ 92.981067] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 0, BandIdx: 0
[ 92.981116] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0
[ 92.981135] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0
[ 92.981171] mt7615_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=6, HT-CentCh=8, VHT-CentCh=42
[ 92.981240] mt7615_apply_cal_data() : eeprom 0x52 bit 1 is 0, do runtime cal , skip RX reload
[ 92.981246] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload
[ 92.981267] MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0
[ 92.981273] BW = 1,TXStream = 2, RXStream = 2, scan(0)
[ 92.985183] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0
[ 93.039124] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 8(Prim=6, HT-CentCh=8, VHT-CentCh=42, BBP_BW=1)
[ 93.042937] MtCmdSetDbdcCtrl:(ret = 0)
[ 93.043453] LeadTimeForBcn, OmacIdx = 11, WDEV_WITH_BCN_ABILITY
[ 93.043597] Generate UUID for apidx(1)
[ 93.043625] UUID: c0bb6c2c, len = 16
[ 93.043691] 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 02 0c 43 36 60 00
[ 93.043692]
[ 93.046103] device rax0 entered promiscuous mode
[ 93.046265] br-lan: port 3(rax0) entered forwarding state
[ 93.046325] br-lan: port 3(rax0) entered forwarding state
[ 93.051196] WifiSysOpen(), wdev idx = 2
[ 93.051521] MtCmdSetDbdcCtrl:(ret = 0)
[ 93.051904] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=44
[ 93.051909] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=44
[ 93.052046] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/49, support 38 channels
[ 93.054552] device apcli0 entered promiscuous mode
[ 93.054708] br-lan: port 4(apcli0) entered forwarding state
[ 93.054767] br-lan: port 4(apcli0) entered forwarding state
[ 93.064004] WifiSysOpen(), wdev idx = 3
[ 93.064388] MtCmdSetDbdcCtrl:(ret = 0)
[ 93.070914] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=6
[ 93.070921] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=6
[ 93.071063] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/49, support 38 channels
[ 93.077246] device apclix0 entered promiscuous mode
[ 93.077551] br-lan: port 5(apclix0) entered forwarding state
[ 93.077657] br-lan: port 5(apclix0) entered forwarding state
[ 93.091283] get_wdev_by_idx: invalid idx(0)
[ 93.091301] get_wdev_by_idx: invalid idx(0)
[ 93.091317] get_wdev_by_idx: invalid idx(0)
[ 93.091331] get_wdev_by_idx: invalid idx(0)
[ 93.091345] get_wdev_by_idx: invalid idx(0)
[ 93.091359] get_wdev_by_idx: invalid idx(0)
[ 93.091529] get_wdev_by_idx: invalid idx(0)
[ 93.091547] DriverOwn()::Return since already in Driver Own...
[ 93.091560] ===============================
[ 93.091571] Current DevInfo Num: 0
[ 93.091579] ===============================
[ 93.091588] ===============================
[ 93.091600] Current BssInfo Num: 0
[ 93.091609] ===============================
[ 93.091619] ===============================
[ 93.091630] Current StaRec Num: 0
[ 93.091639] ===============================
[ 93.320337] multi-profile merge success, en:1,pf1_num:0,pf2_num:1,total:1
[ 93.327871] E2pAccessMode=2
[ 93.329707] SSID[0]=wifi-mt7615.2.2G, EdcaIdx=0
[ 93.332661] RTMPSetProfileParameters(): DBDC Mode=1
[ 93.342879] cfg_mode=9
[ 93.342894] cfg_mode=9
[ 93.342925] wmode_band_equal(): Band Equal!
[ 93.354478] [TxPower] BAND0: 100, BAND1: 100
[ 93.354478] [SKUenable] BAND0: 0, BAND1: 0
[ 93.354478] [PERCENTAGEenable] BAND0: 1, BAND1: 1
[ 93.354478] [BFBACKOFFenable] BAND0: 0, BAND1: 0
[ 93.354478] CalCacheApply = 0
[ 93.360585] APEdca0
[ 93.360957] Valid=1
[ 93.360963] APAifsn[0]=3
[ 93.360967] APAifsn[1]=7
[ 93.360971] APAifsn[2]=1
[ 93.360975] APAifsn[3]=1
[ 93.360990] APEdca1
[ 93.361389] Valid=1
[ 93.361394] APAifsn[0]=3
[ 93.361399] APAifsn[1]=7
[ 93.361403] APAifsn[2]=1
[ 93.361407] APAifsn[3]=1
[ 93.361422] APEdca2
[ 93.361871] APEdca3
[ 93.365941] BSSAifsn[0]=3
[ 93.365946] BSSAifsn[1]=7
[ 93.365950] BSSAifsn[2]=2
[ 93.365955] BSSAifsn[3]=2
[ 93.366606] APSDCapable[0]=0
[ 93.366611] APSDCapable[1]=0
[ 93.366616] default ApCliAPSDCapable[0]=0
[ 93.366621] default ApCliAPSDCapable[1]=0
[ 93.370211] DfsZeroWait Support=1/1
[ 93.371175] DfsZeroWaitCacTime=255/255
[ 93.431324] [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0
[ 93.431582] [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0
[ 93.431836] [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0
[ 93.438445] cfg_mode=15
[ 93.438450] cfg_mode=9
[ 93.450419] AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
[ 93.471883] HT: Ext Channel = ABOVE
[ 93.471900] HT: Ext Channel = ABOVE
[ 93.480596] HT: greenap_cap = 0
[ 93.527185] IcapMode = 0
[ 93.537397] WtcSetMaxStaNum: MaxStaNum:91, BssidNum:1, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:125
[ 93.547728] Top Init Done!
[ 93.550457] Use dev_alloc_skb
[ 93.554561] RX[0] DESC ae39a000 size = 8192
[ 93.559627] RX[1] DESC ae39c000 size = 8192
[ 93.564906] Hif Init Done!
[ 93.567607] ctl->txq = c1372c38
[ 93.570800] ctl->rxq = c1372c44
[ 93.573930] ctl->ackq = c1372c50
[ 93.577138] ctl->kickq = c1372c5c
[ 93.580461] ctl->tx_doneq = c1372c68
[ 93.584016] ctl->rx_doneq = c1372c74
[ 93.588674] mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615))
[ 93.594740] mt7615_fw_prepare(2752): MT7615_E3, USE E3 patch and ram code binary image
[ 93.602642] AndesMTLoadRomMethodFwDlRing(1036), cap->rom_patch_len(11150)
[ 93.609427] AndesRestartCheck: Current TOP_MISC2(0x1)
[ 93.614454] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
[ 93.621316] 20170304031443a
[ 93.624149]
[ 93.625627] platform =
[ 93.628054] ALPS
[ 93.629920] hw/sw version =
[ 93.632783] 8a108a10
[ 93.634965] patch version =
[ 93.637825] 00000010
[ 93.640516] Patch SEM Status=2
[ 93.643601] MtCmdPatchSemGet:(ret = 0)
[ 93.643851] :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0)
[ 93.653371]
[ 93.653371] Patch is not ready && get semaphore success, SemStatus(2)
[ 93.661361] EventGenericEventHandler: CMD Success
[ 93.666081] MtCmdAddressLenReq:(ret = 0)
[ 93.670151] MtCmdPatchFinishReq
[ 93.684553] EventGenericEventHandler: CMD Success
[ 93.689290] Send checksum req..
[ 93.692484] Patch SEM Status=3
[ 93.695553] MtCmdPatchSemGet:(ret = 0)
[ 93.699369]
[ 93.699369] Release patch semaphore, SemStatus(3)
[ 93.705522] AndesMTEraseRomPatch
[ 93.708755] WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0
[ 93.714836] AndesMTLoadFwMethodFwDlRing(810), cap->fw_len(459960)
[ 93.720919] Build Date:_201705121437
[ 93.724529] Build Date:_201705121437
[ 93.728135] AndesRestartCheck: Current TOP_MISC2(0x1)
[ 93.733184] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
[ 93.740154] EventGenericEventHandler: CMD Success
[ 93.744872] MtCmdAddressLenReq:(ret = 0)
[ 93.753267] EventGenericEventHandler: CMD Success
[ 93.758045] MtCmdAddressLenReq:(ret = 0)
[ 93.762508] MtCmdFwStartReq: override = 1, address = 540672
[ 93.768183] EventGenericEventHandler: CMD Success
[ 93.772929] Build Date:_201703141726
[ 93.776611] EventGenericEventHandler: CMD Success
[ 93.781392] MtCmdAddressLenReq:(ret = 0)
[ 93.786282] MtCmdFwStartReq: override = 4, address = 0
[ 93.856828] EventGenericEventHandler: CMD Success
[ 93.895638] WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0
[ 93.901371] MCU Init Done!
[ 93.904105] MtCmdSetRlmPorCal: (ret = 0)
[ 93.908903] efuse_probe: efuse = 10000212
[ 93.912901] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
[ 93.918269] RtmpEepromGetDefault::e2p_dafault=1
[ 93.922801] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
[ 93.930356] NVM is FLASH mode. dev_idx [1] FLASH OFFSET [0x4000]
[ 93.936332] NICReadEEPROMParameters():Calling eeinit
[ 93.942027] RtmpOSFileOpen(): Error 2 opening /etc/wlan/MT7615_EEPROM.bin
[ 93.948819] --> Error opening file /etc/wlan/MT7615_EEPROM.bin
[ 93.954630] Load EEPROM Buffer from default BIN.
[ 93.965946] Cal Free IC!!
[ 93.976311] The EEPROM in Flash is wrong, use default
[ 93.981408] proprietary driver not support flash write, will write on ated.
[ 93.988343] NICReadEEPROMParameters: EEPROM 0x52 b300
[ 93.994105] NICReadEEPROMParameters: EEPROM 0x52 b300
[ 93.999870] Country Region from e2p = 1
[ 94.003692] mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4
[ 94.009894] mt7615_antenna_default_reset(): DBDC 2G TxPath = 2, 2G RxPath = 2
[ 94.017008] mt7615_antenna_default_reset(): DBDC 5G TxPath = 2, 2G RxPath = 2
[ 94.024162] rtmp_read_txpwr_from_eeprom(243): Don't Support this now!
[ 94.030613] RTMPReadTxPwrPerRate(1382): Don't Support this now!
[ 94.036513] RcRadioInit(): DbdcMode=1, ConcurrentBand=2
[ 94.041915] RcRadioInit(): pRadioCtrl=8f51e450,Band=0,rfcap=1,channel=1,PhyMode=2
[ 94.049412] RcRadioInit(): pRadioCtrl=8f51e53c,Band=1,rfcap=2,channel=36,PhyMode=1
[ 94.057223] MtCmdSetDbdcCtrl:(ret = 0)
[ 94.968610] br-lan: port 2(ra0) entered forwarding state
[ 95.038698] br-lan: port 3(rax0) entered forwarding state
[ 95.048623] br-lan: port 4(apcli0) entered forwarding state
[ 95.068621] br-lan: port 5(apclix0) entered forwarding state
[ 100.360336] Band Rf: 1, Phy Mode: 2
[ 100.363828] Band Rf: 2, Phy Mode: 1
[ 100.367297] AntCfgInit(2787): Not support for HIF_MT yet!
[ 100.372764] MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!!
[ 100.378796] MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!!
[ 100.384670] EEPROM Init Done!
[ 100.387625] mt_mac_init()-->
[ 100.390600] mt_mac_pse_init(2787): Don't Support this now!
[ 100.396063] mt7615_init_mac_cr()-->
[ 100.399601] mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c
[ 100.404900] mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c
[ 100.410159] MtAsicSetMacMaxLen(1313): Not finish Yet!
[ 100.415186] <--mt_mac_init()
[ 100.421991] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[ 100.428791] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[ 100.435542] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[ 100.442299] MAC Init Done!
[ 100.445001] MT7615BBPInit():BBP Initialization.....
[ 100.449903] Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2
[ 100.458955] Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0
[ 100.467979] MT7615BBPInit() todo
[ 100.471308] PHY Init Done!
[ 100.475580] tx_pwr_comp_init():NotSupportYet!
[ 100.480331] MtCmdSetMacTxRx:(ret = 0)
[ 100.484239] MtCmdSetMacTxRx:(ret = 0)
[ 100.487976] RcGetHdevByPhyMode():Err! chip not support this PhyMode: !
[ 100.494501] HcSetPhyMode(): Update PhyMode 0 faild, not support this RF
[ 100.501293] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/1, support 38 channels
[ 100.509577] WifiSysOpen(), wdev idx = 0
[ 100.513402] wdev_attr_update(): wdevId0 = 00:0c:43:26:60:d8
[ 100.519288] MtCmdSetDbdcCtrl:(ret = 0)
[ 100.523813] ApAutoChannelAtBootUp----------------->
[ 100.528703] ApAutoChannelAtBootUp: AutoChannelBootup = 0, AutoChannelFlag = 0
[ 100.535803] ApAutoChannelAtBootUp<-----------------
[ 100.540702] Current Channel is 36. DfsZeroWaitSupport=0
[ 100.545948] MtAsicSetChBusyStat(865): Not support for HIF_MT yet!
[ 100.552070] [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0
[ 100.557893] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=6
[ 100.566573] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/1, support 38 channels
[ 100.574915] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1
[ 100.574915] LinkToOmacIdx = 0, LinkToWdevType = 1
[ 100.587798] [RadarStateCheck]Set into RD_NORMAL_MODE
[ 100.591936] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0
[ 100.593329] MtCmdSetDbdcCtrl:(ret = 0)
[ 100.610830] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 0, BandIdx: 0
[ 100.616664] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0
[ 100.623206] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0
[ 100.629253] mt7615_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=6, HT-CentCh=8, VHT-CentCh=0
[ 100.637171] mt7615_apply_cal_data() : eeprom 0x52 bit 1 is 0, do runtime cal , skip RX reload
[ 100.645681] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload
[ 100.654210] MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0
[ 100.663234] BW = 1,TXStream = 2, RXStream = 2, scan(0)
[ 100.698029] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 8(Prim=6, HT-CentCh=8, VHT-CentCh=0, BBP_BW=1)
[ 100.712493] LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY
[ 100.718464] MtAsicSetRalinkBurstMode(2618): Not support for HIF_MT yet!
[ 100.725118] MtAsicSetPiggyBack(802): Not support for HIF_MT yet!
[ 100.731150] MtAsicSetTxPreamble(2597): Not support for HIF_MT yet!
[ 100.737401] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2!
[ 100.744675] AndesLedEnhanceOP: Success!
[ 100.748634] Main bssid = 00:0c:43:26:60:d8
[ 100.762647] AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn
[ 100.768057] MtCmdSetMacTxRx:(ret = 0)
[ 100.772059] MtCmdSetMacTxRx:(ret = 0)
[ 100.775737] fdb_enable()
[ 101.078052] MCS Set = ff ff 00 00 01
[ 101.081658] <==== mt_wifi_init, Status=0
[ 101.085586] MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1
[ 101.090667] MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 0
[ 101.099357] WtcSetMaxStaNum: MaxStaNum:91, BssidNum:1, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:125
[ 101.214706] red_is_enabled: set CR4/N9 RED Enable to 1.
[ 101.219973] cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2.
[ 101.225960] Correct apidx from 0 to 0 for WscUUIDInit
[ 101.231016] Generate UUID for apidx(0)
[ 101.234764] UUID: c1033530, len = 16
[ 101.238339] 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 00 0c 43 26 60 d8
[ 101.244810]
[ 101.249005] device rai0 entered promiscuous mode
[ 101.253736] br-lan: port 6(rai0) entered forwarding state
[ 101.259221] br-lan: port 6(rai0) entered forwarding state
[ 101.269104] WifiSysOpen(), wdev idx = 1
[ 101.273316] MtCmdSetDbdcCtrl:(ret = 0)
[ 101.277784] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=6
[ 101.286329] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=6
[ 101.295292] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/1, support 38 channels
[ 101.306135] device apclii0 entered promiscuous mode
[ 101.311387] br-lan: port 7(apclii0) entered forwarding state
[ 101.317070] br-lan: port 7(apclii0) entered forwarding state
[ 101.888931] :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0)
[ 103.258025] br-lan: port 6(rai0) entered forwarding state
[ 103.308005] br-lan: port 7(apclii0) entered forwarding state
[ 409.893050] AP SETKEYS DONE - AKMMap=WPA2PSK, PairwiseCipher=AES, GroupCipher=TKIP, wcid=1 from 70:8A:09:52:0C:A6
[ 409.893050]
[ 409.904780] PTK:9b7745dcfb2359c77d993d43335d92e02501623a0095172443d71d5fcae6dcfc876036c1afa470f66cdb1680adfc2af26d873d4d30310ab7faacac285f194a2f
[ 410.105793] Rcv Wcid(1) AddBAReq
[ 410.109016] Start Seq = 00000000
[ 426.421471] bb, flush one!
[ 538.862480] Rcv Wcid(1) AddBAReq
[ 538.865819] Start Seq = 00000000
[ 557.782980] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 557.782980] debug info dump as below:
[ 557.782980]
[ 560.292917] BcnCheck: bcn recover for band 1(ra0)!!
[ 560.292917] debug info dump as below:
[ 560.292917]
[ 567.802823] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 567.802823] debug info dump as below:
[ 567.802823]
[ 570.312801] BcnCheck: bcn recover for band 1(ra0)!!
[ 570.312801] debug info dump as below:
[ 570.312801]
[ 585.322611] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 585.322611] debug info dump as below:
[ 585.322611]
[ 587.832598] BcnCheck: bcn recover for band 1(ra0)!!
[ 587.832598] debug info dump as below:
[ 587.832598]
[ 592.842532] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 592.842532] debug info dump as below:
[ 592.842532]
[ 597.852481] BcnCheck: no bcn occurs within 10 sec for band 1(ra0)!!
[ 597.852481] debug info dump as below:
[ 597.852481]
[ 600.362437] BcnCheck: bcn recover for band 1(ra0)!!
[ 600.362437] debug info dump as below:
[ 600.362437]
[ 622.872191] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 622.872191] debug info dump as below:
[ 622.872191]
[ 625.382243] BcnCheck: bcn recover for band 1(ra0)!!
[ 625.382243] debug info dump as below:
[ 625.382243]
[ 632.892081] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 632.892081] debug info dump as below:
[ 632.892081]
[ 637.902019] BcnCheck: bcn recover for band 1(ra0)!!
[ 637.902019] debug info dump as below:
[ 637.902019]
[ 642.911952] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 642.911952] debug info dump as below:
[ 642.911952]
[ 647.921894] BcnCheck: no bcn occurs within 10 sec for band 1(ra0)!!
[ 647.921894] debug info dump as below:
[ 647.921894]
[ 650.431866] BcnCheck: bcn recover for band 1(ra0)!!
[ 650.431866] debug info dump as below:
[ 650.431866]
[ 677.941562] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 677.941562] debug info dump as below:
[ 677.941562]
[ 682.951506] BcnCheck: no bcn occurs within 10 sec for band 1(ra0)!!
[ 682.951506] debug info dump as below:
[ 682.951506]
[ 687.961372] BcnCheck: no bcn occurs within 15 sec for band 1(ra0)!!
[ 687.961372] debug info dump as below:
[ 687.961372]
[ 692.971183] BcnCheck: no bcn occurs within 20 sec for band 1(ra0)!!
[ 692.971183] debug info dump as below:
[ 692.971183]
[ 695.481123] BcnCheck: bcn recover for band 1(ra0)!!
[ 695.481123] debug info dump as below:
[ 695.481123]
[ 770.489177] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 770.489177] debug info dump as below:
[ 770.489177]
[ 775.499121] BcnCheck: no bcn occurs within 10 sec for band 1(ra0)!!
[ 775.499121] debug info dump as below:
[ 775.499121]
[ 780.509084] BcnCheck: bcn recover for band 1(ra0)!!
[ 780.509084] debug info dump as below:
[ 780.509084]
[ 810.518783] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 810.518783] debug info dump as below:
[ 810.518783]
[ 815.528746] BcnCheck: no bcn occurs within 10 sec for band 1(ra0)!!
[ 815.528746] debug info dump as below:
[ 815.528746]
[ 820.538672] BcnCheck: no bcn occurs within 15 sec for band 1(ra0)!!
[ 820.538672] debug info dump as below:
[ 820.538672]
[ 823.048623] BcnCheck: bcn recover for band 1(ra0)!!
[ 823.048623] debug info dump as below:
[ 823.048623]
[ 848.058140] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 848.058140] debug info dump as below:
[ 848.058140]
[ 850.568089] BcnCheck: bcn recover for band 1(ra0)!!
[ 850.568089] debug info dump as below:
[ 850.568089]
[ 873.077739] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 873.077739] debug info dump as below:
[ 873.077739]
[ 875.587647] BcnCheck: bcn recover for band 1(ra0)!!
[ 875.587647] debug info dump as below:
[ 875.587647]
[ 880.597564] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 880.597564] debug info dump as below:
[ 880.597564]
[ 885.607479] BcnCheck: no bcn occurs within 10 sec for band 1(ra0)!!
[ 885.607479] debug info dump as below:
[ 885.607479]
[ 890.617380] BcnCheck: no bcn occurs within 15 sec for band 1(ra0)!!
[ 890.617380] debug info dump as below:
[ 890.617380]
[ 895.627288] BcnCheck: bcn recover for band 1(ra0)!!
[ 895.627288] debug info dump as below:
[ 895.627288]
[ 965.635427] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 965.635427] debug info dump as below:
[ 965.635427]
[ 970.645176] BcnCheck: no bcn occurs within 10 sec for band 1(ra0)!!
[ 970.645176] debug info dump as below:
[ 970.645176]
[ 973.155062] BcnCheck: bcn recover for band 1(ra0)!!
[ 973.155062] debug info dump as below:
[ 973.155062]
[ 993.164136] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 993.164136] debug info dump as below:
[ 993.164136]
[ 998.173940] BcnCheck: bcn recover for band 1(ra0)!!
[ 998.173940] debug info dump as below:
[ 998.173940]
root@LEDE:/# [ 1008.183522] BcnCheck: no bcn occurs within 5 sec for band 1(ra0)!!
[ 1008.183522] debug info dump as below:
[ 1008.183522]
[ 1013.193338] BcnCheck: no bcn occurs within 10 sec for band 1(ra0)!!
[ 1013.193338] debug info dump as below:
[ 1013.193338]
[ 1015.703264] BcnCheck: bcn recover for band 1(ra0)!!
[ 1015.703264] debug info dump as below:
[ 1015.703264]
mtkwifi reload
root@LEDE:/# mtkwifi reload
[ 2704.586323] WifiSysClose(), wdev idx = 0
[ 2704.593086] WifiSysGetBssInfoState(): BssInfoIdx 0 not found!!!
[ 2704.599020] WifiSysUpdateBssInfoState(): BssInfoIdx 0 not found!!!
[ 2704.606821] br-lan: port 2(ra0) entered disabled state
[ 2704.662356] device ra0 left promiscuous mode
[ 2704.666828] br-lan: port 2(ra0) entered disabled state
[ 2704.686495] WifiSysClose(), wdev idx = 0
[ 2704.693485] WifiSysGetBssInfoState(): BssInfoIdx 0 not found!!!
[ 2704.699408] WifiSysUpdateBssInfoState(): BssInfoIdx 0 not found!!!
[ 2704.777963] WifiSysClose(), wdev idx = 1
[ 2704.784732] WifiSysGetBssInfoState(): BssInfoIdx 1 not found!!!
[ 2704.790659] WifiSysUpdateBssInfoState(): BssInfoIdx 1 not found!!!
[ 2704.798356] br-lan: port 3(rax0) entered disabled state
[ 2704.852900] device rax0 left promiscuous mode
[ 2704.857427] br-lan: port 3(rax0) entered disabled state
[ 2704.891176] (ApCliCtrlDisconnectReqAction) 2. Before do ApCliLinkDown. ifIndex = 0, bValid = 0
[ 2704.993121] WifiSysClose(), wdev idx = 2
[ 2704.998047] br-lan: port 4(apcli0) entered disabled state
[ 2705.052953] device apcli0 left promiscuous mode
[ 2705.057692] br-lan: port 4(apcli0) entered disabled state
[ 2705.077570] (ApCliCtrlDisconnectReqAction) 2. Before do ApCliLinkDown. ifIndex = 1, bValid = 0
[ 2705.177636] WifiSysClose(), wdev idx = 3
[ 2705.181842] MtAsicSetPiggyBack(802): Not support for HIF_MT yet!
[ 2705.187954] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=0, LED_CMD=0!
[ 2705.195096] AndesLedEnhanceOP: Success!
[ 2705.198973] WifiSysClose(), wdev idx = 0
[ 2705.202986] MtAsicSetPiggyBack(802): Not support for HIF_MT yet!
[ 2705.209001] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=0, LED_CMD=0!
[ 2705.216158] AndesLedEnhanceOP: Success!
[ 2705.219980] WifiSysClose(), wdev idx = 1
[ 2705.225528] kill LoopBackTxTask task failed!
[ 2705.229921] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=4, LED_CMD=1!
[ 2705.237110] AndesLedEnhanceOP: Success!
[ 2705.246009] AndesRestartCheck: Current TOP_MISC2(0x7)
[ 2705.292485] CmdReStartDLRsp: Status Success!, Status(0)
[ 2705.297735] EventExtEventHandler: Unknown Ext Event(6f)
[ 2705.297745] AndesRestartCheck: TOP_MISC2(1)
[ 2705.297755] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=2, LED_CMD=1!
[ 2705.297784] AndesLedEnhanceOP: Success!
[ 2705.318422] RT28xxPciAsicRadioOff(): Not support for HIF_MT yet!
[ 2705.324523] tx_kickout_fail_count = 0
[ 2705.328216] tx_timeout_fail_count = 0
[ 2705.331859] rx_receive_fail_count = 0
[ 2705.335526] alloc_cmd_msg = 2197
[ 2705.338742] free_cmd_msg = 2197
[ 2705.343793] cut_through_token_list_destroy(): 8dfe1688,8dfe1688
[ 2705.350666] cut_through_token_list_destroy(): 8dfe1698,8dfe1698
[ 2705.362125] FwOwn()::Set Fw Own
[ 2705.369314] RTMP_AllTimerListRelease: Size=0
[ 2705.373884] FwOwn()::Return since already in Fw Own...
[ 2705.379076] <---HwCtrlThread
[ 2705.382941] br-lan: port 5(apclix0) entered disabled state
[ 2705.438419] device apclix0 left promiscuous mode
[ 2705.443187] br-lan: port 5(apclix0) entered disabled state
[ 2705.462928] WifiSysClose(), wdev idx = 1
[ 2705.467615] MtAsicSetPiggyBack(802): Not support for HIF_MT yet!
[ 2705.473635] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=0, LED_CMD=0!
[ 2705.480861] AndesLedEnhanceOP: Success!
[ 2705.493313] MtAsicSetPiggyBack(802): Not support for HIF_MT yet!
[ 2705.499353] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=0, LED_CMD=0!
[ 2705.506510] AndesLedEnhanceOP: Success!
[ 2705.510346] WifiSysClose(), wdev idx = 0
[ 2705.515860] kill LoopBackTxTask task failed!
[ 2705.520237] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=4, LED_CMD=1!
[ 2705.527389] AndesLedEnhanceOP: Success!
[ 2705.536244] AndesRestartCheck: Current TOP_MISC2(0x7)
[ 2705.582936] CmdReStartDLRsp: Status Success!, Status(0)
[ 2705.588195] AndesRestartCheck: TOP_MISC2(1)
[ 2705.592457] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=2, LED_CMD=1!
[ 2705.599612] AndesLedEnhanceOP: Success!
[ 2705.603693] RT28xxPciAsicRadioOff(): Not support for HIF_MT yet!
[ 2705.609745] tx_kickout_fail_count = 0
[ 2705.613389] tx_timeout_fail_count = 0
[ 2705.617060] rx_receive_fail_count = 0
[ 2705.620709] alloc_cmd_msg = 1824
[ 2705.623917] free_cmd_msg = 1824
[ 2705.629813] cut_through_token_list_destroy(): 8df65708,8df65708
[ 2705.636514] cut_through_token_list_destroy(): 8df65718,8df65718
[ 2705.648086] FwOwn()::Set Fw Own
[ 2705.655457] RTMP_AllTimerListRelease: Size=0
[ 2705.659720] FwOwn()::Return since already in Fw Own...
[ 2705.664864] <---HwCtrlThread
[ 2705.668629] br-lan: port 6(apclii0) entered disabled state
[ 2705.723849] device apclii0 left promiscuous mode
[ 2705.728872] br-lan: port 6(apclii0) entered disabled state
[ 2705.769848] DriverOwn()::Try to Clear FW Own...
[ 2706.074783] DriverOwn()::Success to clear FW Own
[ 2706.079402] ===============================
[ 2706.083563] Current DevInfo Num: 0
[ 2706.086961] ===============================
[ 2706.091122] ===============================
[ 2706.095296] Current BssInfo Num: 0
[ 2706.098678] ===============================
[ 2706.102836] ===============================
[ 2706.107011] Current StaRec Num: 0
[ 2706.110307] ===============================
[ 2706.120779] DBDC_MODE is not enable! Not need to merge.
[ 2706.214834] multi-profile merge success, en:1,pf1_num:1,pf2_num:1,total:2
[ 2706.222517] RT_CfgSetMacAddress : invalid length (0)
[ 2706.228269] E2pAccessMode=4
[ 2706.231476] SSID[0]=RTDEV_AP5, EdcaIdx=0
[ 2706.235728] SSID[1]=wifi-mt7615.1.2G, EdcaIdx=1
[ 2706.240695] RTMPSetProfileParameters(): DBDC Mode=1
[ 2706.247172] cfg_mode=15
[ 2706.249607] cfg_mode=15
[ 2706.252043] wmode_band_equal(): Band Equal!
[ 2706.256233] cfg_mode=9
[ 2706.258586] cfg_mode=9
[ 2706.261900] [TxPower] BAND0: 100, BAND1: 100
[SKUenable] BAND0: 0, BAND1: 0
[PERCENTAGEenable] BAND0: 1, BAND1: 0
APEdca0
[ 2706.279016] Valid=1
[ 2706.281103] APAifsn[0]=3
[ 2706.283619] APAifsn[1]=7
[ 2706.286164] APAifsn[2]=1
[ 2706.288691] APAifsn[3]=1
[ 2706.291218] APEdca1
[ 2706.293526] Valid=1
[ 2706.295641] APAifsn[0]=3
[ 2706.298167] APAifsn[1]=7
[ 2706.300684] APAifsn[2]=1
[ 2706.303200] APAifsn[3]=1
[ 2706.305758] APEdca2
[ 2706.308103] APEdca3
[ 2706.313621] BSSAifsn[0]=3
[ 2706.316254] BSSAifsn[1]=7
[ 2706.318866] BSSAifsn[2]=2
[ 2706.321470] BSSAifsn[3]=2
[ 2706.324308] BSSAifsn[0]=3
[ 2706.326940] BSSAifsn[1]=7
[ 2706.329552] BSSAifsn[2]=2
[ 2706.332157] BSSAifsn[3]=2
[ 2706.335189] APSDCapable[0]=0
[ 2706.338060] APSDCapable[1]=0
[ 2706.340925] default ApCliAPSDCapable[0]=0
[ 2706.344911] default ApCliAPSDCapable[1]=0
[ 2706.353764] [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0
[ 2706.379416] [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=1
[ 2706.384963] [PMF]Set_PMFMFPC_Proc:: apidx=1, Desired MFPC=0
[ 2706.390808] [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0
[ 2706.396385] [PMF]Set_PMFMFPR_Proc:: apidx=1, Desired MFPR=0
[ 2706.402155] [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0
[ 2706.408336] [PMF]Set_PMFSHA256_Proc:: apidx=1, Desired PMFSHA256=0
[ 2706.420102] cfg_mode=9
[ 2706.425405] AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
[ 2706.439086] HT: Ext Channel = ABOVE
[ 2706.442558] HT: Ext Channel = ABOVE
[ 2706.447434] HT: greenap_cap = 0
[ 2706.479424] IcapMode = 0
[ 2706.489276] WtcSetMaxStaNum: MaxStaNum:90, BssidNum:2, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:124
[ 2706.499588] Top Init Done!
[ 2706.502289] Use dev_alloc_skb
[ 2706.511192] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[ 2706.518992] cut_through_token_list_init(): 8dc34a88,8dc34a88
[ 2706.525238] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[ 2706.532957] cut_through_token_list_init(): 8dc34a98,8dc34a98
[ 2706.538907] RX[0] DESC ae4b6000 size = 8192
[ 2706.543915] RX[1] DESC ae4b8000 size = 8192
[ 2706.549252] Hif Init Done!
[ 2706.551965] ctl->txq = c0e72c38
[ 2706.555086] ctl->rxq = c0e72c44
[ 2706.558261] ctl->ackq = c0e72c50
[ 2706.561478] ctl->kickq = c0e72c5c
[ 2706.564773] ctl->tx_doneq = c0e72c68
[ 2706.568355] ctl->rx_doneq = c0e72c74
[ 2706.572986] mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615))
[ 2706.579080] mt7615_fw_prepare(2752): MT7615_E3, USE E3 patch and ram code binary image
[ 2706.587005] AndesMTLoadRomMethodFwDlRing(1036), cap->rom_patch_len(11150)
[ 2706.593763] AndesRestartCheck: Current TOP_MISC2(0x1)
[ 2706.598817] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
[ 2706.605760] 20170304031443a
[ 2706.608656]
[ 2706.610137] platform =
[ 2706.612565] ALPS
[ 2706.614402] hw/sw version =
[ 2706.617292] 8a108a10
[ 2706.619484] patch version =
[ 2706.622346] 00000010
[ 2706.624633] Patch SEM Status=1
[ 2706.627758] MtCmdPatchSemGet:(ret = 0)
[ 2706.631489]
[ 2706.631489] Patch is ready, continue to ILM/DLM DL, SemStatus(1)
[ 2706.639086] Patch SEM Status=3
[ 2706.642167] MtCmdPatchSemGet:(ret = 0)
[ 2706.645931]
[ 2706.645931] Release patch semaphore, SemStatus(3)
[ 2706.652087] AndesMTEraseRomPatch
[ 2706.655323] WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0
[ 2706.661390] AndesMTLoadFwMethodFwDlRing(810), cap->fw_len(459960)
[ 2706.667467] Build Date:_201705121437
[ 2706.671076] Build Date:_201705121437
[ 2706.674682] AndesRestartCheck: Current TOP_MISC2(0x1)
[ 2706.679732] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
[ 2706.686654] EventGenericEventHandler: CMD Success
[ 2706.691364] MtCmdAddressLenReq:(ret = 0)
[ 2706.699524] EventGenericEventHandler: CMD Success
[ 2706.704402] MtCmdAddressLenReq:(ret = 0)
[ 2706.708840] MtCmdFwStartReq: override = 1, address = 540672
[ 2706.714481] EventGenericEventHandler: CMD Success
[ 2706.719231] Build Date:_201703141726
[ 2706.722918] EventGenericEventHandler: CMD Success
[ 2706.727655] MtCmdAddressLenReq:(ret = 0)
[ 2706.732491] MtCmdFwStartReq: override = 4, address = 0
[ 2706.803023] EventGenericEventHandler: CMD Success
[ 2706.841994] WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0
[ 2706.847726] MCU Init Done!
[ 2706.850443] MtCmdSetTxLpfCal:(ret = 0)
[ 2706.854207] MtCmdSetTxIqCal:(ret = 0)
[ 2706.857902] MtCmdSetTxDcCal:(ret = 0)
[ 2706.861567] MtCmdSetRxFiCal:(ret = 0)
[ 2706.865258] MtCmdSetRxFdCal:(ret = 0)
[ 2706.868919] MtCmdSetRxFdCal:(ret = 0)
[ 2706.872577] MtCmdSetRxFdCal:(ret = 0)
[ 2706.876273] MtCmdSetRxFdCal:(ret = 0)
[ 2706.879934] MtCmdSetRxFdCal:(ret = 0)
[ 2706.883593] MtCmdSetRxFdCal:(ret = 0)
[ 2706.887286] MtCmdSetRxFdCal:(ret = 0)
[ 2706.890952] MtCmdSetRxFdCal:(ret = 0)
[ 2706.894610] MtCmdSetRxFdCal:(ret = 0)
[ 2706.898298] MtCmdSetRlmPorCal: (ret = 0)
[ 2706.903082] efuse_probe: efuse = 10000212
[ 2706.907093] RtmpChipOpsEepromHook::e2p_type=4, inf_Type=5
[ 2706.912463] RtmpEepromGetDefault::e2p_dafault=1
[ 2706.916993] RtmpChipOpsEepromHook: E2P type(4), E2pAccessMode = 4, E2P default = 1
[ 2706.924524] NVM is BIN mode
[ 2706.927322] NICReadEEPROMParameters():Calling eeinit
[ 2706.932264] rtmp_ee_load_from_bin::src FileName=/etc/wlan/MT7615E_EEPROM1.bin
[ 2706.939526] Load EEPROM Buffer from /etc/wlan/MT7615E_EEPROM1.bin
[ 2706.945663] rtmp_cal_load_from_bin::FileName=/etc/wireless/RT2860/CALDATA1.bin
[ 2706.952885] RtmpOSFileOpen(): Error 2 opening /etc/wireless/RT2860/CALDATA1.bin
[ 2706.960217] Run RXDCOC/TXDPD/PRECAL cmds to generate caldata files
[ 2706.967346] rtmp_ee_bin_init(): bDCOCReloaded = false.
[ 2706.972460] rtmp_cal_load_from_bin::FileName=/etc/wireless/RT2860/CALDATA1.bin
[ 2706.979697] RtmpOSFileOpen(): Error 2 opening /etc/wireless/RT2860/CALDATA1.bin
[ 2706.987009] Run RXDCOC/TXDPD/PRECAL cmds to generate caldata files
[ 2706.994111] rtmp_ee_bin_init(): bDPDReloaded = false.
[ 2707.006534] Cal Free IC!!
[ 2707.017315] NICReadEEPROMParameters: EEPROM 0x52 b300
[ 2707.023043] NICReadEEPROMParameters: EEPROM 0x52 b300
[ 2707.028906] Country Region from e2p = 1
[ 2707.032777] mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4
[ 2707.039020] mt7615_antenna_default_reset(): DBDC 2G TxPath = 2, 2G RxPath = 2
[ 2707.046157] mt7615_antenna_default_reset(): DBDC 5G TxPath = 2, 2G RxPath = 2
[ 2707.053275] rtmp_read_txpwr_from_eeprom(243): Don't Support this now!
[ 2707.059706] RTMPReadTxPwrPerRate(1382): Don't Support this now!
[ 2707.065625] RcRadioInit(): DbdcMode=1, ConcurrentBand=2
[ 2707.070830] RcRadioInit(): pRadioCtrl=8f50e450,Band=0,rfcap=1,channel=1,PhyMode=2
[ 2707.078301] RcRadioInit(): pRadioCtrl=8f50e53c,Band=1,rfcap=2,channel=36,PhyMode=1
[ 2707.086164] MtCmdSetDbdcCtrl:(ret = 0)
[ 2707.610236] Band Rf: 1, Phy Mode: 2
[ 2707.613714] Band Rf: 2, Phy Mode: 1
[ 2707.617215] AntCfgInit(2787): Not support for HIF_MT yet!
[ 2707.622597] MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!!
[ 2707.628612] MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!!
[ 2707.634350] RtmpOSFileOpen(): Error 2 opening /etc/wireless/mt7615/mt7615-sku-bf.dat
[ 2707.642118] EEPROM Init Done!
[ 2707.645076] mt_mac_init()-->
[ 2707.647985] mt_mac_pse_init(2787): Don't Support this now!
[ 2707.653509] mt7615_init_mac_cr()-->
[ 2707.657034] mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c
[ 2707.662240] mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c
[ 2707.667484] MtAsicSetMacMaxLen(1313): Not finish Yet!
[ 2707.672513] <--mt_mac_init()
[ 2707.679324] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[ 2707.686126] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[ 2707.692867] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[ 2707.699550] MAC Init Done!
[ 2707.702249] MT7615BBPInit():BBP Initialization.....
[ 2707.707137] Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2
[ 2707.716164] Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0
[ 2707.725188] MT7615BBPInit() todo
[ 2707.728483] PHY Init Done!
[ 2707.732925] tx_pwr_comp_init():NotSupportYet!
[ 2707.737730] MtCmdSetMacTxRx:(ret = 0)
[ 2707.741646] MtCmdSetMacTxRx:(ret = 0)
[ 2707.745598] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/48, support 38 channels
[ 2707.753946] WifiSysOpen(), wdev idx = 0
[ 2707.757808] wdev_attr_update(): wdevId0 = 28:6c:07:62:6d:f2
[ 2707.763688] MtCmdSetDbdcCtrl:(ret = 0)
[ 2707.768322] ApAutoChannelAtBootUp----------------->
[ 2707.773292] ApAutoChannelAtBootUp: AutoChannelBootup = 0, AutoChannelFlag = 0
[ 2707.780433] ApAutoChannelAtBootUp<-----------------
[ 2707.785318] Current Channel is 36. DfsZeroWaitSupport=0
[ 2707.790584] [PMF]APPMFInit:: Security is not WPA2/WPA2PSK AES
[ 2707.796341] [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0
[ 2707.802234] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:48,Channel=36
[ 2707.811037] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/48, support 38 channels
[ 2707.819485] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1
[ 2707.819485] LinkToOmacIdx = 0, LinkToWdevType = 1
[ 2707.825727] :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0)
[ 2707.838452] [RadarStateCheck]Set into RD_NORMAL_MODE
[ 2707.842425] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196
[ 2707.843082] MtCmdSetDbdcCtrl:(ret = 0)
[ 2707.861967] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 0, BandIdx: 1
[ 2707.867828] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 1
[ 2707.874344] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 1
[ 2707.880392] mt7615_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=36
[ 2707.888613] mt7615_apply_cal_data() : eeprom 0x52 bit 1 is 0, do runtime cal , skip RX reload
[ 2707.897125] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload
[ 2707.905659] MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 38 DBDCIdx= 1, Band= 0
[ 2707.914835] BW = 1,TXStream = 2, RXStream = 2, scan(0)
[ 2708.027866] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 38(Prim=36, HT-CentCh=38, VHT-CentCh=36, BBP_BW=1)
[ 2708.041311] [WrapDfsRadarDetectStart]: Band0Ch is 36[WrapDfsRadarDetectStart]: Band1Ch is 0LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY
[ 2708.054755] MtAsicSetRalinkBurstMode(2618): Not support for HIF_MT yet!
[ 2708.061603] MtAsicSetPiggyBack(802): Not support for HIF_MT yet!
[ 2708.067656] MtAsicSetTxPreamble(2597): Not support for HIF_MT yet!
[ 2708.073856] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2!
[ 2708.081015] AndesLedEnhanceOP: Success!
[ 2708.084924] Main bssid = 28:6c:07:62:6d:f2
[ 2708.098647] AsicRadioOnOffCtrl(): DbdcIdx=1 RadioOn
[ 2708.103805] MtCmdSetMacTxRx:(ret = 0)
[ 2708.107695] MtCmdSetMacTxRx:(ret = 0)
[ 2708.111378] fdb_enable()
[ 2708.414398] MCS Set = ff ff 00 00 01
[ 2708.418006] <==== mt_wifi_init, Status=0
[ 2708.421949] MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1
[ 2708.427019] MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 1
[ 2708.432098] wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw
[ 2708.440351] wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw
[ 2708.448606] WtcSetMaxStaNum: MaxStaNum:90, BssidNum:2, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:124
[ 2708.502691] red_is_enabled: set CR4/N9 RED Enable to 1.
[ 2708.507948] cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2.
[ 2708.513925] Correct apidx from 1 to 0 for WscUUIDInit
[ 2708.518980] Generate UUID for apidx(0)
[ 2708.522728] UUID: c0b33530, len = 16
[ 2708.526309] 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 28 6c 07 62 6d f2
[ 2708.532781]
[ 2708.586822] device ra0 entered promiscuous mode
[ 2708.591456] br-lan: port 2(ra0) entered forwarding state
[ 2708.596833] br-lan: port 2(ra0) entered forwarding state
[ 2708.618004] DriverOwn()::Try to Clear FW Own...
[ 2708.922901] DriverOwn()::Success to clear FW Own
[ 2708.927525] ===============================
[ 2708.931687] Current DevInfo Num: 0
[ 2708.935066] ===============================
[ 2708.939254] ===============================
[ 2708.943426] Current BssInfo Num: 0
[ 2708.946838] ===============================
[ 2708.951006] ===============================
[ 2708.955198] Current StaRec Num: 0
[ 2708.958500] ===============================
[ 2709.074241] multi-profile merge success, en:1,pf1_num:0,pf2_num:1,total:1
[ 2709.082685] E2pAccessMode=1
[ 2709.086039] SSID[0]=wifi-mt7615.2.2G, EdcaIdx=1
[ 2709.091077] RTMPSetProfileParameters(): DBDC Mode=1
[ 2709.097789] cfg_mode=9
[ 2709.100315] cfg_mode=9
[ 2709.102671] wmode_band_equal(): Band Equal!
[ 2709.107928] [TxPower] BAND0: 100, BAND1: 100
[SKUenable] BAND0: 0, BAND1: 0
[PERCENTAGEenable] BAND0: 1, BAND1: 1
[BFBACKOFFenable] BAND0: 0, BAND1: 0
CalCacheApply = 0
[ 2709.130500] APEdca0
[ 2709.132845] Valid=1
[ 2709.134931] APAifsn[0]=3
[ 2709.137482] APAifsn[1]=7
[ 2709.140008] APAifsn[2]=1
[ 2709.142526] APAifsn[3]=1
[ 2709.145050] APEdca1
[ 2709.147474] Valid=1
[ 2709.149562] APAifsn[0]=3
[ 2709.152078] APAifsn[1]=7
[ 2709.154594] APAifsn[2]=1
[ 2709.157140] APAifsn[3]=1
[ 2709.159673] APEdca2
[ 2709.162046] APEdca3
[ 2709.167115] BSSAifsn[0]=3
[ 2709.169800] BSSAifsn[1]=7
[ 2709.172405] BSSAifsn[2]=2
[ 2709.175007] BSSAifsn[3]=2
[ 2709.178148] APSDCapable[0]=0
[ 2709.181015] APSDCapable[1]=0
[ 2709.183878] default ApCliAPSDCapable[0]=0
[ 2709.187895] default ApCliAPSDCapable[1]=0
[ 2709.194356] DfsZeroWait Support=1/1
[ 2709.198585] DfsZeroWaitCacTime=255/255
[ 2709.227058] [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0
[ 2709.232862] [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0
[ 2709.238796] [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0
[ 2709.251501] cfg_mode=15
[ 2709.253936] cfg_mode=9
[ 2709.259733] AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
[ 2709.274134] HT: Ext Channel = ABOVE
[ 2709.277658] HT: Ext Channel = ABOVE
[ 2709.282710] HT: greenap_cap = 0
[ 2709.318732] IcapMode = 0
[ 2709.328982] WtcSetMaxStaNum: MaxStaNum:91, BssidNum:1, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:125
[ 2709.339295] Top Init Done!
[ 2709.341997] Use dev_alloc_skb
[ 2709.350883] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[ 2709.358644] cut_through_token_list_init(): 8ce64408,8ce64408
[ 2709.364827] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[ 2709.372589] cut_through_token_list_init(): 8ce64418,8ce64418
[ 2709.378284] RX[0] DESC adc38000 size = 8192
[ 2709.383303] RX[1] DESC adc3a000 size = 8192
[ 2709.388666] Hif Init Done!
[ 2709.391375] ctl->txq = c12f2c38
[ 2709.394497] ctl->rxq = c12f2c44
[ 2709.397661] ctl->ackq = c12f2c50
[ 2709.400879] ctl->kickq = c12f2c5c
[ 2709.404175] ctl->tx_doneq = c12f2c68
[ 2709.407776] ctl->rx_doneq = c12f2c74
[ 2709.412413] mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615))
[ 2709.418506] mt7615_fw_prepare(2752): MT7615_E3, USE E3 patch and ram code binary image
[ 2709.426421] AndesMTLoadRomMethodFwDlRing(1036), cap->rom_patch_len(11150)
[ 2709.433180] AndesRestartCheck: Current TOP_MISC2(0x1)
[ 2709.438233] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
[ 2709.445353] 20170304031443a
[ 2709.448203]
[ 2709.449684] platform =
[ 2709.452112] ALPS
[ 2709.453949] hw/sw version =
[ 2709.456841] 8a108a10
[ 2709.459034] patch version =
[ 2709.461896] 00000010
[ 2709.464180] Patch SEM Status=1
[ 2709.467320] MtCmdPatchSemGet:(ret = 0)
[ 2709.471052]
[ 2709.471052] Patch is ready, continue to ILM/DLM DL, SemStatus(1)
[ 2709.478655] Patch SEM Status=3
[ 2709.481730] MtCmdPatchSemGet:(ret = 0)
[ 2709.485480]
[ 2709.485480] Release patch semaphore, SemStatus(3)
[ 2709.491634] AndesMTEraseRomPatch
[ 2709.494844] WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0
[ 2709.500934] AndesMTLoadFwMethodFwDlRing(810), cap->fw_len(459960)
[ 2709.507029] Build Date:_201705121437
[ 2709.510639] Build Date:_201705121437
[ 2709.514259] AndesRestartCheck: Current TOP_MISC2(0x1)
[ 2709.519311] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0)
[ 2709.526281] EventGenericEventHandler: CMD Success
[ 2709.531011] MtCmdAddressLenReq:(ret = 0)
[ 2709.539176] EventGenericEventHandler: CMD Success
[ 2709.543932] MtCmdAddressLenReq:(ret = 0)
[ 2709.548351] MtCmdFwStartReq: override = 1, address = 540672
[ 2709.553979] EventGenericEventHandler: CMD Success
[ 2709.558729] Build Date:_201703141726
[ 2709.562425] EventGenericEventHandler: CMD Success
[ 2709.567162] MtCmdAddressLenReq:(ret = 0)
[ 2709.572131] MtCmdFwStartReq: override = 4, address = 0
[ 2709.642687] EventGenericEventHandler: CMD Success
[ 2709.681489] WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0
[ 2709.687221] MCU Init Done!
[ 2709.689952] MtCmdSetTxLpfCal:(ret = 0)
[ 2709.693710] MtCmdSetTxIqCal:(ret = 0)
[ 2709.697411] MtCmdSetTxDcCal:(ret = 0)
[ 2709.701088] MtCmdSetRxFiCal:(ret = 0)
[ 2709.704756] MtCmdSetRxFdCal:(ret = 0)
[ 2709.708445] MtCmdSetRxFdCal:(ret = 0)
[ 2709.712117] MtCmdSetRxFdCal:(ret = 0)
[ 2709.715806] MtCmdSetRxFdCal:(ret = 0)
[ 2709.719476] MtCmdSetRxFdCal:(ret = 0)
[ 2709.723141] MtCmdSetRxFdCal:(ret = 0)
[ 2709.726835] MtCmdSetRxFdCal:(ret = 0)
[ 2709.730513] MtCmdSetRxFdCal:(ret = 0)
[ 2709.734178] MtCmdSetRxFdCal:(ret = 0)
[ 2709.737866] MtCmdSetRlmPorCal: (ret = 0)
[ 2709.742652] efuse_probe: efuse = 10000212
[ 2709.746666] RtmpChipOpsEepromHook::e2p_type=1, inf_Type=5
[ 2709.752043] RtmpEepromGetDefault::e2p_dafault=1
[ 2709.756577] RtmpChipOpsEepromHook: E2P type(1), E2pAccessMode = 1, E2P default = 1
[ 2709.764110] NVM is EFUSE mode
[ 2709.767084] NICReadEEPROMParameters():Calling eeinit
[ 2709.772026] NVM is Efuse and its size =3c[3c0-3fb]
[ 2709.777083] Load EEPROM buffer from efuse, and change to BIN buffer mode
[ 2709.795889] efuse_probe: efuse = 10000212
[ 2709.799882] RtmpChipOpsEepromHook::forceMode: 4 , infType: 5
[ 2709.805532] RtmpChipOpsEepromHook: E2P type(4), E2pAccessMode = 1, E2P default = 0
[ 2709.813064] NVM is BIN mode
[ 2709.815873] NICReadEEPROMParameters: EEPROM 0x52 b300
[ 2709.821596] NICReadEEPROMParameters: EEPROM 0x52 b300
[ 2709.827345] Country Region from e2p = 101
[ 2709.831350] mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4
[ 2709.837523] mt7615_antenna_default_reset(): DBDC 2G TxPath = 2, 2G RxPath = 2
[ 2709.844624] mt7615_antenna_default_reset(): DBDC 5G TxPath = 2, 2G RxPath = 2
[ 2709.851761] rtmp_read_txpwr_from_eeprom(243): Don't Support this now!
[ 2709.858203] RTMPReadTxPwrPerRate(1382): Don't Support this now!
[ 2709.864101] RcRadioInit(): DbdcMode=1, ConcurrentBand=2
[ 2709.869323] RcRadioInit(): pRadioCtrl=8f654450,Band=0,rfcap=1,channel=1,PhyMode=2
[ 2709.876799] RcRadioInit(): pRadioCtrl=8f65453c,Band=1,rfcap=2,channel=36,PhyMode=1
[ 2709.884527] MtCmdSetDbdcCtrl:(ret = 0)
[ 2710.408786] Band Rf: 1, Phy Mode: 2
[ 2710.412271] Band Rf: 2, Phy Mode: 1
[ 2710.415801] AntCfgInit(2787): Not support for HIF_MT yet!
[ 2710.421196] MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!!
[ 2710.427245] MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!!
[ 2710.432985] RtmpOSFileOpen(): Error 2 opening /etc/wireless/mt7615/mt7615-sku-bf.dat
[ 2710.440755] EEPROM Init Done!
[ 2710.443712] mt_mac_init()-->
[ 2710.446620] mt_mac_pse_init(2787): Don't Support this now!
[ 2710.452083] mt7615_init_mac_cr()-->
[ 2710.455596] mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c
[ 2710.460801] mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c
[ 2710.466040] MtAsicSetMacMaxLen(1313): Not finish Yet!
[ 2710.471069] <--mt_mac_init()
[ 2710.477852] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[ 2710.484599] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[ 2710.491400] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
[ 2710.497993] MAC Init Done!
[ 2710.500692] MT7615BBPInit():BBP Initialization.....
[ 2710.505575] Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2
[ 2710.514579] Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0
[ 2710.523598] MT7615BBPInit() todo
[ 2710.526913] PHY Init Done!
[ 2710.531141] tx_pwr_comp_init():NotSupportYet!
[ 2710.535906] MtCmdSetMacTxRx:(ret = 0)
[ 2710.539841] MtCmdSetMacTxRx:(ret = 0)
[ 2710.543502] RcGetHdevByPhyMode():Err! chip not support this PhyMode: !
[ 2710.550035] HcSetPhyMode(): Update PhyMode 0 faild, not support this RF
[ 2710.556938] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/1, support 38 channels
[ 2710.565233] WifiSysOpen(), wdev idx = 0
[ 2710.569062] wdev_attr_update(): wdevId0 = 00:00:00:00:00:00
[ 2710.574947] MtCmdSetDbdcCtrl:(ret = 0)
[ 2710.579531] ApAutoChannelAtBootUp----------------->
[ 2710.584389] ApAutoChannelAtBootUp: AutoChannelBootup = 0, AutoChannelFlag = 0
[ 2710.591514] ApAutoChannelAtBootUp<-----------------
[ 2710.595094] br-lan: port 2(ra0) entered forwarding state
[ 2710.601673] Current Channel is 36. DfsZeroWaitSupport=0
[ 2710.606973] [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0
[ 2710.612799] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=6
[ 2710.621487] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/1, support 38 channels
[ 2710.629844] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1
[ 2710.629844] LinkToOmacIdx = 0, LinkToWdevType = 1
[ 2710.642735] [RadarStateCheck]Set into RD_NORMAL_MODE
[ 2710.646864] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0
[ 2710.648262] MtCmdSetDbdcCtrl:(ret = 0)
[ 2710.665747] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 0, BandIdx: 0
[ 2710.671578] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0
[ 2710.678111] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0
[ 2710.684136] mt7615_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=6, HT-CentCh=8, VHT-CentCh=0
[ 2710.692087] MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0
[ 2710.701110] BW = 1,TXStream = 2, RXStream = 2, scan(0)
[ 2710.860566] :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0)
[ 2710.873315] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 8(Prim=6, HT-CentCh=8, VHT-CentCh=0, BBP_BW=1)
[ 2710.887678] LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY
[ 2710.893623] MtAsicSetRalinkBurstMode(2618): Not support for HIF_MT yet!
[ 2710.900247] MtAsicSetPiggyBack(802): Not support for HIF_MT yet!
[ 2710.906252] MtAsicSetTxPreamble(2597): Not support for HIF_MT yet!
[ 2710.912468] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2!
[ 2710.919623] AndesLedEnhanceOP: Success!
[ 2710.923526] Main bssid = 00:00:00:00:00:00
[ 2710.931853] AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn
[ 2710.937358] MtCmdSetMacTxRx:(ret = 0)
[ 2710.941228] MtCmdSetMacTxRx:(ret = 0)
[ 2710.944895] fdb_enable()
[ 2711.248161] MCS Set = ff ff 00 00 01
[ 2711.251760] <==== mt_wifi_init, Status=0
[ 2711.255737] MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1
[ 2711.260788] MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 0
[ 2711.265883] WtcSetMaxStaNum: MaxStaNum:91, BssidNum:1, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:125
[ 2711.373848] red_is_enabled: set CR4/N9 RED Enable to 1.
[ 2711.379100] cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2.
[ 2711.385112] Correct apidx from 0 to 0 for WscUUIDInit
[ 2711.390143] Generate UUID for apidx(0)
[ 2711.393889] UUID: c0fb3530, len = 16
[ 2711.397465] 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 00 00 00 00 00 00
[ 2711.403935]
[ 2711.477154] WifiSysOpen(), wdev idx = 1
[ 2711.481002] wdev_attr_update(): wdevId1 = 2a:6c:07:72:6d:f2
[ 2711.486843] MtCmdSetDbdcCtrl:(ret = 0)
[ 2711.490983] [PMF]APPMFInit:: apidx=1, MFPC=0, MFPR=0, SHA256=0
[ 2711.496858] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=6
[ 2711.505500] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/48, support 38 channels
[ 2711.513906] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:126 for WDEV_TYPE:1
[ 2711.513906] LinkToOmacIdx = 11, LinkToWdevType = 1
[ 2711.526899] [RadarStateCheck]Set into RD_NORMAL_MODE
[ 2711.530887] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0
[ 2711.531620] MtCmdSetDbdcCtrl:(ret = 0)
[ 2711.549878] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 0, BandIdx: 0
[ 2711.555730] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0
[ 2711.562244] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0
[ 2711.568287] mt7615_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=6, HT-CentCh=8, VHT-CentCh=36
[ 2711.576316] mt7615_apply_cal_data() : eeprom 0x52 bit 1 is 0, do runtime cal , skip RX reload
[ 2711.584799] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload
[ 2711.593324] MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0
[ 2711.602353] BW = 1,TXStream = 2, RXStream = 2, scan(0)
[ 2711.646681] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 8(Prim=6, HT-CentCh=8, VHT-CentCh=36, BBP_BW=1)
[ 2711.660332] LeadTimeForBcn, OmacIdx = 11, WDEV_WITH_BCN_ABILITY
[ 2711.666402] Generate UUID for apidx(1)
[ 2711.670159] UUID: c0b36c2c, len = 16
[ 2711.673714] 0x0000 : bc 32 9e 00 1d d8 11 b2 86 01 2a 6c 07 72 6d f2
[ 2711.680212]
[ 2711.732793] device rax0 entered promiscuous mode
[ 2711.737601] br-lan: port 3(rax0) entered forwarding state
[ 2711.743059] br-lan: port 3(rax0) entered forwarding state
[ 2711.778975] WifiSysOpen(), wdev idx = 2
[ 2711.783048] MtCmdSetDbdcCtrl:(ret = 0)
[ 2711.787258] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:48,Channel=36
[ 2711.795892] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:48,Channel=36
[ 2711.804594] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/48, support 38 channels
[ 2711.865552] device apcli0 entered promiscuous mode
[ 2711.870478] br-lan: port 4(apcli0) entered forwarding state
[ 2711.876133] br-lan: port 4(apcli0) entered forwarding state
[ 2711.897468] WifiSysOpen(), wdev idx = 3
[ 2711.901601] MtCmdSetDbdcCtrl:(ret = 0)
[ 2711.905996] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=6
[ 2711.914482] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=6
[ 2711.923198] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/48, support 38 channels
[ 2711.983424] device apclix0 entered promiscuous mode
[ 2711.988493] br-lan: port 5(apclix0) entered forwarding state
[ 2711.994197] br-lan: port 5(apclix0) entered forwarding state
[ 2712.015681] WifiSysOpen(), wdev idx = 1
[ 2712.020124] MtCmdSetDbdcCtrl:(ret = 0)
[ 2712.024777] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=6
[ 2712.033955] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=6
[ 2712.042675] CountryCode(2.4G/5G)=5/7, RFIC=25, PHY mode(2.4G/5G)=14/1, support 38 channels
[ 2712.103542] device apclii0 entered promiscuous mode
[ 2712.108629] br-lan: port 6(apclii0) entered forwarding state
[ 2712.114320] br-lan: port 6(apclii0) entered forwarding state
root@LEDE:/# [ 2713.735083] br-lan: port 3(rax0) entered forwarding state
[ 2713.875091] br-lan: port 4(apcli0) entered forwarding state
[ 2713.985072] br-lan: port 5(apclix0) entered forwarding state
[ 2714.105074] br-lan: port 6(apclii0) entered forwarding state
the issue seems is that 2G and 5G calibration are different,but the 7615 wifi driver just get /lib/firmware/mt7615.eeprom.bin, i will fix it so, and i will tell you the correct calibration data file names.
e2p files in /lib/firmware/ like "mt7615.1.eeprom.bin mt7615.2.eeprom.bin mt7615.3.eeprom.bin". mt7615.1.eeprom.bin for ra0,the first card mt7615.2.eeprom.bin for rai0,the second card, mt7615.3.eeprom.bin for the third card
normally,the first card is 2G,the second card is 5G. you may try the lastest ko later. it will build so.
it's a little complicated for dual-band chips like mt7615.
as @ZiqiangYu stated, the 7615 driver can be working on either 2g or 5g band, depending on its profile (.dat) and eeprom (.bin). so if you got more than 1 mt7615 chips on your set, you will need 1 profile and 1 eeprom binary for every device/band.
for example, you got 2 mt7615, one works on 2G band, the other works on 5G band, then you will need:
/etc/wireless/mt7615/mt7615.1.dat /etc/wireless/mt7615/mt7615.2.dat /lib/firmware/mt7615.1.eeprom.bin /lib/firmware/mt7615.2.eeprom.bin
when the 1st 7615 chip init, the driver will looking for /etc/wireless/mt7615/mt7615.1.dat and /lib/firmware/mt7615.1.eeprom.bin. it is the same for the 2nd 7615.
if you missed these files (or wrong path), there will be errors in the console/dmesg when bringing up wifi interfaces, and wifi may work improperly.
What about the MT7615D chipset support, with independent dual band?
On Apr 18, 2018, at 12:22 AM, Hua Shao [email protected] wrote:
it's a little complicated for dual-band chips like mt7615.
as @ZiqiangYu https://github.com/ZiqiangYu stated, the 7615 driver can be working on either 2g or 5g band, depending on its profile (.dat) and eeprom (.bin). so if you got more than 1 mt7615 chips on your set, you will need 1 profile and 1 eeprom binary for every device/band.
for example, you got 2 mt7615, one works on 2G band, the other works on 5G band, then you will need:
/etc/wireless/mt7615/mt7615.1.dat /etc/wireless/mt7615/mt7615.2.dat /lib/firmware/mt7615.1.eeprom.bin /lib/firmware/mt7615.2.eeprom.bin
when the 1st 7615 chip init, the driver will looking for /etc/wireless/mt7615/mt7615.1.dat and /lib/firmware/mt7615.1.eeprom.bin. it is the same for the 2nd 7615.
if you missed these files (or wrong path), there will be errors in the console/dmesg when bringing up wifi interfaces, and wifi may work improperly.
— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub https://github.com/Nossiac/mtk-openwrt-feeds/issues/26#issuecomment-382289568, or mute the thread https://github.com/notifications/unsubscribe-auth/Agf-EGdDl9IrhLaT1p6FeKykxjBUUM4yks5tpunJgaJpZM4SWfF_.
