MKFirmware
autoleveling G29
Send: G29 Recv: Echo: 0.240 0.210 -0.023 -0.130 -0.237 -0.320 -0.370 -0.300 0.790 Recv: Echo: -0.037 0.100 0.077 0.440 0.397 0.297 0.237 0.513 0.667 Recv: Echo: -0.153 -0.097 0.383 -0.033 -0.400 -0.707 -0.977 -1.387 -0.010 Recv: Echo: -0.063 0.293 0.207 0.393 0.570 0.433 0.070 -0.557 0.213 Recv: Echo: -0.230 0.003 -0.247 -0.483 -0.780 -0.920 -0.793 -0.157 0.437 Recv: Echo: -0.710 1.800 1.887 1.847 1.640 1.257 0.740 0.167 0.500 Recv: Echo: -1.190 0.453 -0.890 -2.133 -3.190 -3.960 -4.350 -4.497 0.563 Recv: Echo: 0.543 0.457 3.430 3.493 2.650 0.907 -1.567 4.550 4.940 Recv: Echo: 0.397 -6.517 -7.047 -6.423 -5.773 -4.077 -2.380 -0.683 6.660 Recv: X:0.00 Y:0.00 Z:20.00 E:0.00 Count Alpha:25285 Beta:25285 Teta:25285
no comment ! -6.660mm ??? with my mecanical comparator +-0.1mm default...
well it's just not possible that measures more than 1 mm of default on the bed
because if I mechanically measured with a probe I find maximum 0.1mm fake on the bed! So how come you found it 6mm?
The firmware is a first probe to a center, and calculates the difference between the point the probe and the height. If it's ok should give 0. After various probes, and it calculates the difference between that point and the center. If the floor is not level by those values.
and my config :
Send: M501 Recv: Echo: V25 stored settings retrieved (335 bytes) Recv: Config: Steps per unit: Recv: Config: M92 X100.00 Y100.00 Z100.00 E99.35 Recv: Config: Maximum feedrates (mm/s): Recv: Config: M203 X500.00 Y500.00 Z500.00 E100.00 Recv: Config: Maximum Acceleration (mm/s2): Recv: Config: M201 X5000 Y5000 Z5000 E1000 Recv: Recv: Config: Accelerations: P=printing, V=travel and T* R=retract Recv: Config: M204 P3000.00 V3000.00 Recv: Config: M204 T0 R10000.00 Recv: Config: Advanced variables: S=Min feedrate (mm/s), V=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s) Recv: Config: M205 S0.00 V0.00 B20000 X20.00 Z20.00 E5.00 Recv: Config: Home offset (mm): Recv: Config: M206 X0.00 Y0.00 Z0.00 Recv: Config: Delta Geometry adjustment: Recv: Config: M666 A0.000 B0.000 C0.000 I0.000 J0.000 K0.000 U0.000 V0.000 W0.000 R178.75 D291.55 H191.50 Recv: Config: Endstop Offsets: Recv: Config: M666 X0.00 Y0.00 Z0.00 Recv: Config: Z-Probe Offset: Recv: Config: M666 P X0.00 Y20.00 Z-1.00 Recv: Config: PID settings: Recv: Config: M301 H
OK your High is correctly? Down width Z and check is nozzle touch the plain at zero...
It's ok, now the 0.046 is possible error for Z PROBE OFFSET... Now when you give command G29 the firmware chek the center this point is zero.. When check another poin the value is differenze from center point... If you have big difference you must do the autocalibration width G30 A command...
Recv: Echo: 1.433 0.887 0.297 0.207 0.323 0.467 0.610 0.547 -0.243 Recv: Echo: -0.810 0.813 0.477 0.137 0.150 0.163 0.203 -0.247 -0.697 Recv: Echo: -0.777 -0.647 0.193 0.067 -0.023 -0.140 -0.250 -0.280 -0.900 Recv: Echo: -0.483 -0.483 -0.483 -0.427 -0.343 -0.253 -0.203 -0.153 -0.180 Recv: Echo: -0.450 -0.320 -0.190 -0.030 0.137 0.347 0.593 0.830 0.993 Recv: Echo: 2.020 1.627 1.233 0.863 0.577 0.377 0.353 0.427 0.670 Recv: Echo: 3.443 1.123 0.627 0.243 -0.110 -0.460 -0.870 -1.433 -2.190 Recv: Echo: 4.867 0.390 -4.250 -3.117 -2.360 -1.930 -1.830 -1.910 -3.220 Recv: Echo: 0.153 -8.743 -6.123 -2.917 -1.713 -0.610 0.577 -2.387 -4.250
I SEND A G30 A...
Send: G29 Recv: Echo: -0.370 -0.313 -0.180 -0.100 -0.133 -0.203 -0.233 -0.177 0.333 Recv: Echo: 0.373 -0.203 -0.187 -0.080 -0.057 -0.063 -0.050 0.233 0.360 Recv: Echo: 0.350 0.247 -0.037 -0.060 0.020 0.077 0.133 0.163 0.257 Recv: Echo: 0.227 0.173 0.120 0.130 0.067 0.033 0.023 0.067 0.153 Recv: Echo: 0.130 0.063 -0.003 -0.007 -0.033 -0.060 -0.123 -0.193 -0.273 Recv: Echo: -0.650 -0.527 -0.403 -0.310 -0.223 -0.183 -0.167 -0.203 -0.233 Recv: Echo: -1.050 -0.320 -0.120 0.047 0.180 0.307 0.430 0.630 0.850 Recv: Echo: -1.120 0.070 1.260 0.913 0.700 0.623 0.590 0.697 1.427 Recv: Echo: 0.260 2.473 1.647 0.773 0.353 -0.073 -0.563 0.763 2.003 Recv: X:0.00 Y:0.00 Z:20.00 E:0.00 Count Alpha:25033 Beta:25158 Teta:25033
The autocalibration may take time. Can be up to one hour ... I'm going to sleep... Tomorrow i read you result..
This is center line probe Recv: Echo: 0.130 0.063 -0.003 -0.007 -0.033 -0.060 -0.123 -0.193 -0.273 Look the center point is ~0 but the extreme point front and behind no.. You have problem width delta radius... The autocalibration correct it..