zigbee2mqtt TS0601 _TZE204_lzriup1j wrong order in 'Preset'

What happened?

the 'Preset' setting is displayed incorrectly. when I select auto mode on the thermostat, manual mode is displayed in the GUI. and vice versa.

What did you expect to happen?

change order in https://github.com/Koenkk/zigbee-herdsman-converters/blob/34de76fe3d1ffb2aa6dbcd712ceb5178f38712f9/src/devices/tuya.ts#L4352 ?

How to reproduce it (minimal and precise)

No response

Zigbee2MQTT version

1.40.1-dev commit: d3de77d

Adapter firmware version

7.4.2

Adapter

ember/skyconnect

Setup

unraid docker

Debug log

No response

Sep 17 '24 06:09 arkadi222

Could you provide a screenshot of the device about tab?

Sep 18 '24 18:09 Koenkk

2024-09-19_13h02_50 2024-09-19_13h02_31 20240919_130207

Sep 19 '24 11:09 arkadi222

2024-09-19_13h05_02

Sep 19 '24 11:09 arkadi222

@vobelic, since you also have this device, could you confirm this issue?

Sep 20 '24 20:09 Koenkk

@tispokes, @Akrotkiv, @vmrk00, @roon7, @poky0611 - maybe you can confirm also ?

Sep 30 '24 07:09 arkadi222

@arkadi222 @Koenkk may can check it this week. I'm moving so I'm not on my old flat

Sep 30 '24 08:09 tispokes

@arkadi222 idk, I don't use that, I created new thermostat to my boiler with ESPhome via OpenTherm protocol. I high recommended If your boiler can communicate in OpenTherm: https://github.com/arthurrump/esphome-opentherm

Sep 30 '24 08:09 vmrk00

@Koenkk I'm running 1.39.0, and can't confirm an issue. No time to upgrade now. Changing the preset on the thermostat shows the correct mode in Z2M.

Sep 30 '24 17:09 vobelic

@vobelic are you sure that your device presents itself as: _TZE204_lzriup1j (not _TZE200_viy9ihs7) ? because I see that both models share the same configuration - maybe it is a reason ? I can confirm my issue for each of the 5 thermostats I have :(

Sep 30 '24 22:09 arkadi222

@arkadi222 yes it's the Zigbee Manufacturer: _TZE204_lzriup1j

Once I do an update I'll let you know.

Btw what do the logs in Z2M look like when you change from auto to manual and v/s? e.g. 2024-10-02 20:24:58z2m:mqtt: MQTT publish: topic 'zigbee2mqtt/Living Room Thermostat', payload '{"backlight":3,"backlight_mode":"high","child_lock":"UNLOCK","current_heating_setpoint":18,"deadzone_temperature":1,"factory_reset":"OFF","faultalarm":0,"frost_protection":"ON","holiday_mode":"no_rest","last_seen":"2024-10-02T20:24:58+02:00","linkquality":142,"local_temperature":23.2,"local_temperature_calibration":-1,"max_temperature":6,"max_temperature_limit":60,"preset":"manual","running_state":"idle","schedule_holiday":"08:00/22.0°C 23:00/16.0°C","schedule_weekday":"06:00/20.0°C 08:00/16.0°C 11:30/16.0°C 12:30/16.0°C 17:00/22.0°C 22:00/16.0°C","sensor":"internal","sensor_mode":"in","system_mode":"heat","temperature_difference_start":1,"working_day":"6-1"}'

Oct 02 '24 18:10 vobelic

when I change from auto to manual: 2024-10-04 07:47:31z2m:mqtt: MQTT publish: topic 'zigbee2mqtt/Sypialnia termostat', payload '{"backlight_mode":"off","child_lock":"UNLOCK","current_heating_setpoint":21,"deadzone_temperature":0.5,"factory_reset":"OFF","faultalarm":0,"frost_protection":"OFF","inverse":"OFF","key_sound":"ON","last_seen":"2024-10-04T07:47:12+02:00","linkquality":160,"local_temperature":22.6,"local_temperature_calibration":-2.5,"max_temperature_limit":26,"preset":"manual","running_state":"idle","schedule_holiday":"08:00/23.0°C 23:00/20.0°C","schedule_weekday":"06:00/24.0°C 06:55/21.0°C 13:05/23.5°C 15:55/22.0°C 21:05/23.0°C 23:30/21.0°C","sensor":"both","sensor_choice":"inside","sensor_limit":60,"system_mode":"heat","working_day":"5-2"}' 2024-10-04 07:47:36z2m:mqtt: MQTT publish: topic 'zigbee2mqtt/Sypialnia termostat', payload '{"backlight_mode":"off","child_lock":"UNLOCK","current_heating_setpoint":21,"deadzone_temperature":0.5,"factory_reset":"OFF","faultalarm":0,"frost_protection":"OFF","inverse":"OFF","key_sound":"ON","last_seen":"2024-10-04T07:47:17+02:00","linkquality":152,"local_temperature":22.6,"local_temperature_calibration":-2.5,"max_temperature_limit":26,"preset":"auto","running_state":"idle","schedule_holiday":"08:00/23.0°C 23:00/20.0°C","schedule_weekday":"06:00/24.0°C 06:55/21.0°C 13:05/23.5°C 15:55/22.0°C 21:05/23.0°C 23:30/21.0°C","sensor":"both","sensor_choice":"inside","sensor_limit":60,"system_mode":"heat","working_day":"5-2"}' from manual to auto: 2024-10-04 07:53:15z2m:mqtt: MQTT publish: topic 'zigbee2mqtt/Sypialnia termostat', payload '{"backlight_mode":"off","child_lock":"UNLOCK","current_heating_setpoint":22.5,"deadzone_temperature":0.5,"factory_reset":"OFF","faultalarm":0,"frost_protection":"OFF","inverse":"OFF","key_sound":"ON","last_seen":"2024-10-04T07:52:57+02:00","linkquality":152,"local_temperature":22.4,"local_temperature_calibration":-2.5,"max_temperature_limit":26,"preset":"auto","running_state":"idle","schedule_holiday":"08:00/23.0°C 23:00/20.0°C","schedule_weekday":"06:00/24.0°C 06:55/21.0°C 13:05/23.5°C 15:55/22.0°C 21:05/23.0°C 23:30/21.0°C","sensor":"both","sensor_choice":"inside","sensor_limit":60,"system_mode":"heat","working_day":"5-2"}' 2024-10-04 07:53:17z2m:mqtt: MQTT publish: topic 'zigbee2mqtt/Sypialnia termostat', payload '{"backlight_mode":"off","child_lock":"UNLOCK","current_heating_setpoint":22.5,"deadzone_temperature":0.5,"factory_reset":"OFF","faultalarm":0,"frost_protection":"OFF","inverse":"OFF","key_sound":"ON","last_seen":"2024-10-04T07:52:58+02:00","linkquality":160,"local_temperature":22.4,"local_temperature_calibration":-2.5,"max_temperature_limit":26,"preset":"manual","running_state":"idle","schedule_holiday":"08:00/23.0°C 23:00/20.0°C","schedule_weekday":"06:00/24.0°C 06:55/21.0°C 13:05/23.5°C 15:55/22.0°C 21:05/23.0°C 23:30/21.0°C","sensor":"both","sensor_choice":"inside","sensor_limit":60,"system_mode":"heat","working_day":"5-2"}' it doesn't matter whether I do it with home assistant or from the thermostat.

Oct 04 '24 05:10 arkadi222

I've just used https://gist.github.com/Koenkk/4b4c582f8a01fd71108acce6a5e2db15 :) and changed line: 85 in my ext_converter file: if (device.manufacturerName === '_TZE204_lzriup1j') { now it works perfect for me :D

Oct 08 '24 08:10 arkadi222

Hi, I've created a issue abbout "EventBus error" messages: https://github.com/Koenkk/zigbee2mqtt/issues/23874 and after apply this solution https://github.com/Koenkk/zigbee2mqtt/issues/23874#issuecomment-2395572178 error log messages disappeared! But now I've the problem detailed in this issue: Auto and Manual mode are interchanged. My Manufactured device data id is the same: _TZE204_lzriup1j

Oct 09 '24 16:10 Danieldiazi

This issue is stale because it has been open 180 days with no activity. Remove stale label or comment or this will be closed in 30 days

Dec 11 '24 00:12 github-actions[bot]