RFLink Gateway to MQTT

Purpose

Bridge between RFLink Gateway and MQTT broker.

Current features

Forwarding messages received on TTY port from RFLink Gateway Arduino board to MQTT broker in both directions.

Every message received from RFLinkGateway is split into single parameters and published to different MQTT topics. Example: Message:

20;37;Acurite;ID=cbd5;TEMP=0066;HUM=79;WINSP=001a;BAT=OK

ASCII

/data/RFLINK/Acurite/cbd5/READ/TEMP 10.2
/data/RFLINK/Acurite/cbd5/READ/HUM 73
/data/RFLINK/Acurite/cbd5/READ/WINSP 2.6
/data/RFLINK/Acurite/cbd5/READ/BAT OK

JSON

/data/RFLINK/Acurite/cbd5/READ/TEMP {"value": 10.2}
/data/RFLINK/Acurite/cbd5/READ/HUM {"value": 73}
/data/RFLINK/Acurite/cbd5/READ/WINSP {"value": 2.6}
/data/RFLINK/Acurite/cbd5/READ/BAT {"value": "OK"}

Every message received on particular MQTT topic is translated to RFLink Gateway and sent to 433 MHz.

Installation

Install the dependencies with the following commands:

pip install -r requirements.txt

Configuration

Whole configuration is located in config.json file. You can copy and edit config.json.sample.

{
  "mqtt_host": "your_mqtt_host",
  "mqtt_port": 1883,
  "mqtt_prefix": "/data/RFLINK",
  "mqtt_format": "json",
  "mqtt_message_timeout": 60,
  "mqtt_user":"your_mqtt_user",
  "mqtt_password":"your_mqtt_password",
  "rflink_tty_device": "/dev/ttyUSB0",
  "rflink_direct_output_params": [
    "BAT",
    "CMD",
    "SET_LEVEL",
    "SWITCH",
    "HUM",
    "CHIME",
    "PIR",
    "SMOKEALERT"
  ],
  "rflink_signed_output_params": [
    "TEMP",
    "WINCHL",
    "WINTMP"
  ],
  "rflink_wdir_output_params": [
    "WINDIR"
  ]
}

Running

Scripts assume script directory located at: /opt/scripts/RFLinkGateway, and virtualenv was used. If not, use system Python binary, not the virtualenv'ed one.

Running in Supervisor

vim supervisor_RFLinkGateway
cp supervisor_RFLinkGateway /etc/supervisor/conf.d/
supervisorctl reread
supervisorctl update
supervisorctl start RFLinkGateway

Start as a Service

vim RFLinkGateway.service
cp RFLinkGateway.service /lib/systemd/system/RFLinkGateway.service
sudo systemctl daemon-reload
sudo systemctl enable RFLinkGateway.service

Start as a docker container

cd /opt/scripts/RFLinkGateway
docker build --tag rflink .
docker run --name rflinkgw -v /path/to/configfile:/app/config.json --device=/dev/ttyUSB0:/dev/ttyUSB0:rw rflink:latest

Logging

Script logs to STDOUT, it can be redirected through supervisord to files or syslog. For docker you can use any driver (such a Loki).

Output data

Application pushes informations to MQTT broker in following format: [mqtt_prefix]/[device_type]/[device_id]/READ/[parameter]

/data/RFLINK/TriState/8556a8/READ/1 OFF

Except if there its a CMD (Normally a signal from a switch), it is pushed to the following topic: [mqtt_prefix]/[device_type]/[device_id]/[switch_id]/READ/[parameter]

like this, you only have to read the command message to use with devices with two or more switches

/data/RFLINK/NewKaku/0201e3fa/2/READ/CMD ON

Every change should be published to topic: [mqtt_prefix]/[device_type]/[device_id]/W/[switch_ID]

/data/RFLINK/TriState/8556a8/W/1 ON

References

• RFLink Gateway project http://www.rflink.nl/
• RFLink Gateway protocol http://www.rflink.nl/blog2/protref