wdmc2-kernel
wdmc2-kernel copied to clipboard
Heisath
Tweak can't apply
I managed to install Debian 12 with the latest 6.1.x kernel on my wd cloud. However, the LAN speed is terrible. I can't even get > 20MB/s. I try to apply the tweak with the internet but it failed.
root@wdmycloud:/etc/samba# ethtool -C eth0 pkt-rate-low 20000 pkt-rate-high 3000000 rx-frames 32 rx-usecs 1150 rx-usecs-high 1150 rx-usecs-low 100 rx-frames-low 32 rx-frames-high 32 adaptive-rx on
netlink error: cannot modify an unsupported parameter (offset 100)
netlink error: Invalid argument
Here are some other info
root@wdmycloud:/etc/samba# ethtool -i eth0
driver: mvpp2
version: 1.0
firmware-version:
expansion-rom-version:
bus-info: eth0
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
root@wdmycloud:/etc/samba# ethtool -c eth0
Coalesce parameters for eth0:
Adaptive RX: n/a TX: n/a
stats-block-usecs: n/a
sample-interval: n/a
pkt-rate-low: n/a
pkt-rate-high: n/a
rx-usecs: 1150
rx-frames: 32
rx-usecs-irq: n/a
rx-frames-irq: n/a
tx-usecs: 1000
tx-frames: 64
tx-usecs-irq: n/a
tx-frames-irq: n/a
rx-usecs-low: n/a
rx-frame-low: n/a
tx-usecs-low: n/a
tx-frame-low: n/a
rx-usecs-high: n/a
rx-frame-high: n/a
tx-usecs-high: n/a
tx-frame-high: n/a
CQE mode RX: n/a TX: n/a
root@wdmycloud:/etc/samba# ethtool -s eth0
root@wdmycloud:/etc/samba# ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: on
master-slave cfg: preferred slave
master-slave status: slave
Port: MII
PHYAD: 0
Transceiver: external
Link detected: yes
root@wdmycloud:/etc/samba# modinfo mvpp2
name: mvpp2
filename: (builtin)
license: GPL v2
file: drivers/net/ethernet/marvell/mvpp2/mvpp2
author: Marcin Wojtas <[email protected]>
description: Marvell PPv2 Ethernet Driver - www.marvell.com
parm: queue_mode:Set queue_mode (single=0, multi=1) (int)
root@wdmycloud:/etc/samba# uname -a
Linux wdmycloud 6.1.104+ #2 SMP Mon Aug 12 00:18:37 EDT 2024 armv7l GNU/Linux
root@wdmycloud:/etc/samba# lsmod
Module Size Used by
overlay 102400 0
udp_diag 16384 0
md_mod 118784 0
sg 28672 0
fuse 102400 1
configfs 32768 1
ip_tables 20480 0
ipv6 368640 41 udp_diag
root@wdmycloud:/etc/samba# lsb_release -a
No LSB modules are available.
Distributor ID: Debian
Description: Debian GNU/Linux 12 (bookworm)
Release: 12
Codename: bookworm
Do you have idea what is wrong? Thanks a lot for your help
Maybe try leaving out some of the parameters to figure out which one exactly is not applying. We can't expect the mycloud to work with newer and newer kernels without problems. So if nothing else works, use an older one.
