edgetx
edgetx copied to clipboard
EdgeTX
Tx16s loosing default settings after three or four restarts
Is there an existing issue for this problem?
- [X] I have searched the existing issues
What part of EdgeTX is the focus of this bug?
Transmitter firmware
Current Behavior
Following three or four restarts of tx the radio reverts back to default settings and has to be re calibrated. This did not happen under open tx.
Expected Behavior
Retain its memory following restarts.
Steps To Reproduce
Turn on tx. Then power down.
Version
2.7.1
Transmitter
Radiomaster TX16S
Anything else?
No response
Also, RM have commented that they have
found there is a chance that the SD card initialization will fail on boot, in such a case the system may be stuck for 20s or more. ... reduces the problem of SD card data corruption requiring the card to be formatted and rebuilt.
Ben said it seems to be more prone to happen as the SD card size increases... so it seems like something else to look into...
Also, RM have commented that they have
found there is a chance that the SD card initialization will fail on boot, in such a case the system may be stuck for 20s or more. ... reduces the problem of SD card data corruption requiring the card to be formatted and rebuilt.
Ben said it seems to be more prone to happen as the SD card size increases... so it seems like something else to look into...
I had this SD stuck issue at boot. Occurred randomly and when it struck it took up to 40s to boot. I solved this by getting rid of the Samsung EVO SD Card and replacing it with a Sandisk. Never had this problem again. Just a few days ago I met a guy with the same problem. Guess which card he had? There is definitely a problem with certain SD Cards. If you want to chase this get a hold of a Samsung EVO SD Card 32GB or 64GB.
Thanks for that... that seems to be what I've seen also... my lockups seemed to be with 32GB EVOs... (and never when I was in a position to run the debugger 😆 ) so I've now got a bunch of Sandisk Extreme 32GBs as well to see how that goes. I would normally have used 16GB EVOs as I've found them generally very reliable and consistent but just can't buy them any more :(
@pfeerick I'll try to acquire the guy's card I talked to recently. This card definitely shows the problem. If I succeed I'll send it to you.
Don't try too hard just yet... we're chasing a few squirrels with RM atm as they have some reproducible failure cases and are set up to do some cycle testing on multiple radios... ;)
On Mon, Aug 8, 2022 at 9:00 PM Michael @.***> wrote:
@pfeerick https://github.com/pfeerick I'll try to acquire the guy's card I talked to recently. This card definitely shows the problem. If I succeed I'll send it to you.
— Reply to this email directly, view it on GitHub https://github.com/EdgeTX/edgetx/issues/2191#issuecomment-1207975140, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABJ66KM2FWY37U4HPDG3WTDVYDSEPANCNFSM55YID4CQ . You are receiving this because you were mentioned.Message ID: @.***>
Have installed latest nightly. Looking very positive at the moment, time will tell. Will carry on testing over week and post back at weekend. Think there may be another bug though. I tried to flash latest multi protocol module and it failed, had to re flash open tx for it to work.
Fingers crossed. And there was a mention of an issue with MPM recently, so thanks for the reminder to look into that.
Have been testing all week, everything seem fine other than ghost lua is now not working. Like new interface by the way.
On 12 Sep 2022, at 09:12, Peter Feerick @.***> wrote:
Fingers crossed. And there was a mention of an issue with MPM recently, so thanks for the reminder to look into that.
— Reply to this email directly, view it on GitHub, or unsubscribe. You are receiving this because you were mentioned.
Have been testing all week, everything seem fine other than ghost lua is now not working. Like new interface by the way. … On 12 Sep 2022, at 09:12, Peter Feerick @.***> wrote: Fingers crossed. And there was a mention of an issue with MPM recently, so thanks for the reminder to look into that. — Reply to this email directly, view it on GitHub, or unsubscribe. You are receiving this because you were mentioned.
Thank you very much for testing.
other than ghost lua is now not working.
You use Ghost? :) What's wrong with the Lua?
Would you mind giving this version of the widget a spin and seeing what you think... I started making some changes to it but got distracted with other stuff... be interesting to see if it works for you or could still be improved.