Anime4000
Leox LXT-010S-H vlan problem
I bought leox LXT-010S-H as a replacement for ISP provided Zhone ZNID-GPON-2424-EU. I changed data to immitate Zhone device and i get O5 gpon state. My ISP is using VEIP and on top of that DHCP for address provisioning. Also i have multicast IPTV on a separate VLAN.
VLANs: 246 multicast IPTV 725 DHCP
At the first i didn't get any data comming from sfp interface. I contacted with Leox support and they provided me with firmware supporting VEIP. After firmware upgrade i started to recieve around 100Mb/s of data on sfp interface. It was multicast traffic on vlan246. I changed mac address on the router and enabled dhcp client on vlan 725, but there was no response. I also tried to bridge vlan 246 with ethernet port connected to STB. Unfortunately there was no television.
Looking on PON statistics i see increasing amount of recieved data but number of data sent is 0 even though i am sending data to a proper VLAN on sfp interface.
I tried this command omcicli mib set 84 0x02 FwdOp 0x02 but it haven't changed anything.
Firmware that supports VEIP will have a V at the end, but I see your photo above is only V3.3.4L4. It should have been V3.3.4LV. Is there a mistake here or did Leox change the naming rules?
Firmware that supports VEIP will have a V at the end, but I see your photo above is only V3.3.4L4. It should have been V3.3.4LV. Is there a mistake here or did Leox change the naming rules?
My bad This screenshot was taken with firmware V3.3.4L4. On this software version there was no data on sfp port. I recieved firmware V3.3.4L5VT and V3.3.4L5V from leox support. On V3.3.4L5V OMCI_OLT_MODE=3 wasn't working, on V3.3.4L5VT OMCI_OLT_MODE=3 was working, i was receiving data on vlan 246, but data send by my router wasn't shown in pon statistics, exactly like on the screen shot.
ISP - > router is working Router - > ISP isn't working
DHCP (IPOE) sometimes needs MAC Address Cloning on SFP Interface, try to clone the MAC Address of original ONT WAN Interface.
DHCP (IPOE) sometimes needs MAC Address Cloning on SFP Interface, try to clone the MAC Address of original ONT WAN Interface.
I did that as a first thing. Weird thing is that my sfp module recieves DHCP requests but don't forward them to the optical interface.
DHCP (IPOE) sometimes needs MAC Address Cloning on SFP Interface, try to clone the MAC Address of original ONT WAN Interface.
I did that as a first thing. Weird thing is that my sfp module recieves DHCP requests but don't forward them to the optical interface.
You can try it at the same time: 1, clone MAC ONT ---> MAC SFP GPON (Leox) 2, clone MAC port WAN Router (before running) ---> MAC port WAN router (new) (in this case, the sfp port)
I'm gonna watch this thread closely as I've got my stick yesterday, installed V3.3.4L5 and it doesn't work too :) I wonder if I need V or VT too (what's the difference between them anyway?) for Orange Slovakia (they use different VLAN's for INT, TV and VOIP too)...
DHCP (IPOE) sometimes needs MAC Address Cloning on SFP Interface, try to clone the MAC Address of original ONT WAN Interface.
I did that as a first thing. Weird thing is that my sfp module recieves DHCP requests but don't forward them to the optical interface.
You can try it at the same time: 1, clone MAC ONT ---> MAC SFP GPON (Leox) 2, clone MAC port WAN Router (before running) ---> MAC port WAN router (new) (in this case, the sfp port)
Which command should i use to change ONT MAC? I don't think it is the problem. I am sending requests and looks like the request is not send by the module to the OLT (bytes send counter is 0). I think sfp module doesn't permit packets from sfp to pon interface.
ROUTER -> SFP works SFP -> PON doesn't work
have you tried to change FwdOp to 0x02 ? (Bridge, no investigation)
Yes i tried this solution. There was no change to the traffic. Should i do anything more after typing this command, like replugging fiber or something?
That was the first thing i did. They provided me different firmware versions and to try omcicli mib set 84 0x02 FwdOp 0x02 . For two weeks i haven't received a message from them.
Can I try to install firmware from different SFP module with the same SoC on this one?
RTL9601CI = V2801F, TWCGPON657 and many others, yea, but Leox stick is build differently even using same SoC, I would not recommend to flash it
if want to test, I advised you dump/backup whole SPI Flash, then you can try flash different fw