ioBroker.zwave2
ioBroker.zwave2 copied to clipboard
AlCalzone
After rpi update upgrade adapter crashes
After normal Pi5 update Adapter is not working anymore. Any ideas ?
Installierte Version: 3.1.0 jscontroller: 6.0.11 Plattform: linux Betriebssystem: linux Architektur: arm64 Geschwindigkeit: 2400 MHz Modell: Cortex-A76 RAM: 7.8 GB Node.js: v20.17.0 NPM: 10.8.2
`
zwave2.0 | 2024-09-07 08:03:29.435 | error | Restarting the adapter in a second... -- | -- | -- | -- zwave2.0 | 2024-09-07 08:03:29.434 | error | Failed to initialize the driver: ZWaveError: Timeout while waiting for an ACK from the controller (ZW0200) at Driver.sendMessage (/opt/iobroker/node_modules/zwave-js/src/lib/driver/Driver.ts:4360:23) at ZWaveController.interview (/opt/iobroker/node_modules/zwave-js/src/lib/controller/Controller.ts:964:22) at Driver.initializeControllerAndNodes (/opt/iobroker/node_modules/zwave-js/src/lib/driver/Driver.ts:1427:27) at Immediate.
Try unplugging and re-inserting the Z-Wave stick. Double check that the path is correct.
Try unplugging and re-inserting the Z-Wave stick. Double check that the path is correct.
I'm using the Razberry board (no usb stick, just the board i think 2.0). Could it be the serial config of the pi5 changed through upgrade ?
Restartet and replugged everything but no change
Tried to find the board but failed
pi@iobroker:~ $ ls -l /dev/serial/by-id
total 0
lrwxrwxrwx 1 root root 13 Sep 7 08:33 usb-Texas_Instruments_CC2538_USB_CDC-if00 -> ../../ttyACM0
pi@iobroker:~ $
CommandLine
console=tty1 console=serial0,115200 root=PARTUUID=d007c190-02 rootfstype=ext4 fsck.repair=yes rootwait
Boot Config
pi@iobroker:~ $ sudo nano /boot/firmware/config.txt
GNU nano 7.2 /boot/firmware/config.txt
# For more options and information see
# http://rptl.io/configtxt
# Some settings may impact device functionality. See link above for details
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
# Additional overlays and parameters are documented
# /boot/firmware/overlays/README
# Automatically load overlays for detected cameras
camera_auto_detect=1
# Automatically load overlays for detected DSI displays
display_auto_detect=1
# Automatically load initramfs files, if found
auto_initramfs=1
# Enable DRM VC4 V3D driver
dtoverlay=vc4-kms-v3d
max_framebuffers=2
# Don't have the firmware create an initial video= setting in cmdline.txt.
# Use the kernel's default instead.
disable_fw_kms_setup=1
# Run in 64-bit mode
arm_64bit=1
# Disable compensation for displays with overscan
disable_overscan=1
# Run as fast as firmware / board allows
arm_boost=1
dtoverlay=disable-bt
dtoverlay=disable-wifi
enable_uart=1
force_turbo=1
[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
# (e.g. for USB device mode) or if USB support is not required.
otg_mode=1
[all]
dtparam=uart0=on
According to https://www.home-assistant.io/docs/z-wave/controllers/#raspberry-pi-5-procedure RPi5 needs a different config.txt change than previous versions, namely
dtoverlay=uart0
instead of
dtoverlay=disable-bt
enable_uart=1