WLED
WLED copied to clipboard
Aircoookie
ESP32 S2 touch threshold has no effect
What happened?
I'm running WLED 0.15.0-b4 on ESP32 S2 Mini. Adjusting the touch threshold doesn't change anything. Sensitivity doesn't change, it doesn't make any difference if I set the threshold to 1 or to 100. Sensitivity is always too low.
To Reproduce Bug
Attach a touch surface to the board and play around with the touch threshold.
Expected Behavior
Changing the threshold should change the sensitivity
Install Method
Binary from WLED.me
What version of WLED?
0.15.0-b4
Which microcontroller/board are you seeing the problem on?
ESP32-S2
Relevant log/trace output
No response
Anything else?
I think this is related to https://github.com/Aircoookie/WLED/pull/3798 and the shifting of touchThreshold in https://github.com/DedeHai/WLED/blob/15526bd6e8c7a75ee1e36cf24ae397a674f63c56/wled00/cfg.cpp#L260
touchAttachInterrupt(btnPin[s], touchButtonISR, touchThreshold<<4); //threshold on Touch V2 is much higher (1500 is a value given by Espressif example)
Maybe the shifting causes a scaling issue.
Code of Conduct
- [X] I agree to follow this project's Code of Conduct
I will take a look. If I remember correctly, the base value is automatically adjusted (auto calibration) and thresholf is just for fine-tuning but that may be a misconception on my side. What was the exact geometry and setup of your touch button?
I started to compile the firmware on my own and played around with the mentioned threshold scaling. I could achieve the desired sensitivity by lowering the threshold significantly. In my tests including touch buttons behind plastic covers, values around 100 worked best.
With ESP32 Wroom I observed that I had to increase the threshold to get a higher sensitivity but for Touch V2 it seems to be opposite. Setting the threshold < 100 results in ghost touches for some buttons. On the other hand setting the threshold static to 65300 results in no sensitivity at all.
So I think that we need to find a proper range to implement a better scaling. I modified the scaling to allow values between 50 and 3050. At least for the buttons I tested with, the range seems to be suitable.
I pushed my current changes to https://github.com/RobinMeis/WLED/blob/9c7afedece573d0611541cfe372f48fbd9b0c056/wled00/cfg.cpp#L299
What was the exact geometry and setup of your touch button?
For testing I used a round copper plate with a diameter of 18mm behind different thin plastic cards to simulate a hidden button. Without the plastic cards it worked. The real "button" is actually a coil spring that is part of a light.
Both worked well with ESP32 Wroom, but I could only get them working with ESP32 S2 after the described modifications.
So I think that we need to find a proper range to implement a better scaling. I modified the scaling to allow values between 50 and 3050. At least for the buttons I tested with, the range seems to be suitable.
Bit contradictory. The code uses a range from 0 to 4080 (at least it should, no PC access RN to check), which you say does not do anything. Could it be just a missing typecast?
It doesn't. What I replaced from current 0_15 branch was
256 + (touchThreshold << 4)
which won't allow to go below 256, but yes, not adding 256 should also work and would be a cleaner solution, just missed to test this while playing around
I have the same problem, meaning there is no response at all on a touch. I like to check my config first to exclude a possible wrong setting or so, before I build and flash.
ESP32 wemos S2 mini version v0.14.4 "Hoshi"
In prefeferences: Button 0 GPIO 14 - Touch Currently I have a 10cm wire connected to GPIO 14 with a stripped end of about 4 cm
@RobinMeis : Do you have a comparable config?
Hi, I have not been able to get touch working with a 5cm wire using the "SEEEDSTUDIO XIAO ESP32S3". I have tried on multiple pins and on multiple boards with the version 0.15.0-b5.
If you need help with your setup, this is not the place, please use Discord or Discourse forum. Touch works fine on S3 in 0.15-B5.