Problem reading using this lib on esp32 + ECC508A

[themagicm]

I'm using an ESP32-WROOM-32D connected to an ECC508A via SDA and SCL. Both have 4.7k resistors.

I am using example 1 configure, example 2 sign and then data from example 2 into example 3 verify. Verification fails:

================Config:

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0030,len:1184 load:0x40078000,len:13260 load:0x40080400,len:3028 entry 0x400805e4 Successful wakeUp(). I2C connections are good.

Serial Number: 0123877DBB070B14EE Rev Number: 00005000 Config Zone: NOT Locked Data/OTP Zone: NOT Locked Data Slot 0: NOT Locked

Would you like to configure your Cryptographic Co-processor with SparkFun Standard settings? (y/n) Note, this is PERMANENT and cannot be changed later If you do not want to do this, type an 'n' or unplug now.

Configuration beginning. Write Config: Success! Lock Config: Success! Key Creation: Success! Lock Data-OTP: Success! Lock Slot 0: Success! Configuration done.

Serial Number: 0123877DBB070B14EE Rev Number: 00005000 Config Zone: Locked Data/OTP Zone: Locked Data Slot 0: Locked

This device's Public Key:

uint8_t publicKey[64] = { 0xE5, 0xDC, 0x8B, 0x6F, 0x47, 0xAC, 0xA0, 0x62, 0x83, 0x18, 0x5A, 0xB6, 0xFF, 0x3D, 0x36, 0xAB, 0xAF, 0xF5, 0xF1, 0x9D, 0xBB, 0xAB, 0x84, 0xC1, 0xD8, 0xDC, 0xCF, 0x66, 0x28, 0xFE, 0x97, 0x3F, 0xDC, 0x24, 0x57, 0xD3, 0x1B, 0xB6, 0x36, 0x60, 0xAA, 0x9D, 0x89, 0x29, 0x7E, 0x14, 0xDB, 0xE8, 0x35, 0x98, 0xD6, 0x81, 0xB6, 0x39, 0xD0, 0xEA, 0x94, 0x1C, 0xC7, 0xDA, 0x3B, 0xF7, 0x83, 0x94 };

==============SIGN:

Successful wakeUp(). I2C connections are good.

Serial Number: 0123877DBB070B14EE Rev Number: 00005000 Config Zone: Locked Data/OTP Zone: Locked Data Slot 0: Locked

This device's Public Key:

uint8_t publicKey[64] = { 0xE5, 0xDC, 0x8B, 0x6F, 0x47, 0xAC, 0xA0, 0x62, 0x83, 0x18, 0x5A, 0xB6, 0xFF, 0x3D, 0x36, 0xAB, 0xAF, 0xF5, 0xF1, 0x9D, 0xBB, 0xAB, 0x84, 0xC1, 0xD8, 0xDC, 0xCF, 0x66, 0x28, 0xFE, 0x97, 0x3F, 0xDC, 0x24, 0x57, 0xD3, 0x1B, 0xB6, 0x36, 0x60, 0xAA, 0x9D, 0x89, 0x29, 0x7E, 0x14, 0xDB, 0xE8, 0x35, 0x98, 0xD6, 0x81, 0xB6, 0x39, 0xD0, 0xEA, 0x94, 0x1C, 0xC7, 0xDA, 0x3B, 0xF7, 0x83, 0x94 };

uint8_t message[32] = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B, 0x0C, 0x0D, 0x0E, 0x0F, 0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x17, 0x18, 0x19, 0x1A, 0x1B, 0x1C, 0x1D, 0x1E, 0x1F };

uint8_t signature[64] = { 0x43, 0x03, 0xE2, 0xFE, 0x1E, 0x0C, 0xB3, 0x21, 0x3E, 0x4C, 0xE5, 0x2E, 0xE6, 0xBE, 0x38, 0xA0, 0x2E, 0x4C, 0xCC, 0x74, 0x9C, 0x6F, 0x16, 0x05, 0xE4, 0xAC, 0xAF, 0x45, 0x88, 0x43, 0xB9, 0xC9, 0xA0, 0xBF, 0x1D, 0x69, 0x9A, 0x76, 0xBB, 0xC3, 0x0B, 0x84, 0xDF, 0x11, 0x3A, 0x19, 0xDB, 0x90, 0x6C, 0xDA, 0xAE, 0x95, 0xAA, 0x31, 0x86, 0xA3, 0x4C, 0x16, 0x09, 0x78, 0xA8, 0x66, 0x2F, 0x94 };

==============VERIFY: Successful wakeUp(). I2C connections are good.

Serial Number: 0123877DBB070B14EE Rev Number: 00005000 Config Zone: Locked Data/OTP Zone: Locked Data Slot 0: Locked

uint8_t publicKeyExternal[64] = { 0xE5, 0xDC, 0x8B, 0x6F, 0x47, 0xAC, 0xA0, 0x62, 0x83, 0x18, 0x5A, 0xB6, 0xFF, 0x3D, 0x36, 0xAB, 0xAF, 0xF5, 0xF1, 0x9D, 0xBB, 0xAB, 0x84, 0xC1, 0xD8, 0xDC, 0xCF, 0x66, 0x28, 0xFE, 0x97, 0x3F, 0xDC, 0x24, 0x57, 0xD3, 0x1B, 0xB6, 0x36, 0x60, 0xAA, 0x9D, 0x89, 0x29, 0x7E, 0x14, 0xDB, 0xE8, 0x35, 0x98, 0xD6, 0x81, 0xB6, 0x39, 0xD0, 0xEA, 0x94, 0x1C, 0xC7, 0xDA, 0x3B, 0xF7, 0x83, 0x94 };

uint8_t message[32] = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x08, 0x09, 0x0A, 0x0B, 0x0C, 0x0D, 0x0E, 0x0F, 0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x17, 0x18, 0x19, 0x1A, 0x1B, 0x1C, 0x1D, 0x1E, 0x1F };

uint8_t signature[64] = { 0x43, 0x03, 0xE2, 0xFE, 0x1E, 0x0C, 0xB3, 0x21, 0x3E, 0x4C, 0xE5, 0x2E, 0xE6, 0xBE, 0x38, 0xA0, 0x2E, 0x4C, 0xCC, 0x74, 0x9C, 0x6F, 0x16, 0x05, 0xE4, 0xAC, 0xAF, 0x45, 0x88, 0x43, 0xB9, 0xC9, 0xA0, 0xBF, 0x1D, 0x69, 0x9A, 0x76, 0xBB, 0xC3, 0x0B, 0x84, 0xDF, 0x11, 0x3A, 0x19, 0xDB, 0x90, 0x6C, 0xDA, 0xAE, 0x95, 0xAA, 0x31, 0x86, 0xA3, 0x4C, 0x16, 0x09, 0x78, 0xA8, 0x66, 0x2F, 0x94 };

Verification failure.

[lewispg228]

Hi there, Sorry you've been having issues with this example.

I am currently rounding up some hardware to see if I can replicate this issue.

For now, I do have one idea for you to try:

These examples do require a larger-ish i2c buffer. If you can adjust your wire.h file before compiling, I might try increasing this from 128 to 256. I believe the hookup guide was created with the Artemis because this defaults to 256.

For reference, it is located here in the espressif github repo:

https://github.com/espressif/arduino-esp32/blob/master/libraries/Wire/src/Wire.h#L43

And it usually lives deep within your arduino install here-ish:

C:\Users\user.name\AppData\Local\Arduino15\packages\esp32\hardware\esp32\2.0.11\libraries\Wire\src

But I'm also wondering if something changed with the recent big update to Arduino "2.0", so we may need to dig deeper.

I'll keep ya posted on how testing goes on our end. Thanks, -Pete

[themagicm]

PETE!!! YOU GENIUS!

Wire.setBufferSize(256); WORKED!

Sent with Proton Mail secure email.

------- Original Message ------- On Monday, July 31st, 2023 at 3:57 PM, Pete Lewis @.***> wrote:

Hi there, Sorry you've been having issues with this example.

I am currently rounding up some hardware to see if I can replicate this issue.

For now, I do have one idea for you to try:

These examples do require a larger-ish i2c buffer. If you can adjust your wire.h file before compiling, I might try increasing this from 128 to 256. I believe the hookup guide was created with the Artemis because this defaults to 256.

For reference, it is located here in the espressif github repo:

https://github.com/espressif/arduino-esp32/blob/master/libraries/Wire/src/Wire.h#L43

And it usually lives deep within your arduino install here-ish:

C:\Users\user.name\AppData\Local\Arduino15\packages\esp32\hardware\esp32\2.0.11\libraries\Wire\src

But I'm also wondering if something changed with the recent big update to Arduino "2.0", so we may need to dig deeper.

I'll keep ya posted on how testing goes on our end. Thanks, -Pete

— Reply to this email directly, view it on GitHub, or unsubscribe. You are receiving this because you authored the thread.Message ID: @.***>

[lewispg228]

Excellent! Glad it was resolved so easily and qwiicly for you :) Hope the rest of your authentication project goes well! This reminds me, I need to update my garage door opener to accept new public keys.

[themagicm]

cool. whats the private key? lol I kid I kid.