platform-ststm32
platform-ststm32 copied to clipboard
platformio
Uploading to Arduino Opta fails: libusb-1.0.0.dylib not loaded?
On MacBook Pro M2 (Mac OS 13.3.1) running PlatformIO IDE v3.3.1 in VS Code 1.82.2
Main error: dyld[2890]: Library not loaded: /usr/local/opt/libusb/lib/libusb-1.0.0.dylib
Uploading from Arduino IDE works fine. The device is actually at /dev/cu.usbmodem1101.
platformio.ini contains only:
[env:opta]
platform = ststm32
board = opta
framework = arduino
Attempting to upload and run the "Testing with Blink Sketch" code gets me the following:
* Executing task: platformio run --target upload --upload-port /dev/cu.usbmodem1101
Processing opta (platform: ststm32; board: opta; framework: arduino)
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Verbose mode can be enabled via `-v, --verbose` option
CONFIGURATION: https://docs.platformio.org/page/boards/ststm32/opta.html
PLATFORM: ST STM32 (16.1.0) > Arduino Opta
HARDWARE: STM32H747XIH6 480MHz, 511.35KB RAM, 768KB Flash
DEBUG: Current (cmsis-dap) External (cmsis-dap, jlink, stlink)
PACKAGES:
- framework-arduino-mbed @ 4.0.2
- tool-dfuutil @ 1.11.0
- tool-openocd @ 3.1200.0 (12.0)
- tool-stm32duino @ 1.0.1
- toolchain-gccarmnoneeabi @ 1.70201.0 (7.2.1)
LDF: Library Dependency Finder -> https://bit.ly/configure-pio-ldf
LDF Modes: Finder ~ chain, Compatibility ~ soft
Found 42 compatible libraries
Scanning dependencies...
No dependencies
Building in release mode
Checking size .pio/build/opta/firmware.elf
Advanced Memory Usage is available via "PlatformIO Home > Project Inspect"
RAM: [= ] 10.9% (used 57152 bytes from 523624 bytes)
Flash: [= ] 14.0% (used 109760 bytes from 786432 bytes)
Building .pio/build/opta/firmware.bin
Adding dfu suffix to firmware.bin
dyld[2890]: Library not loaded: /usr/local/opt/libusb/lib/libusb-1.0.0.dylib
Referenced from: <2C64C116-83B7-3F20-B5BF-951356492177> /Users/ken.martin/.platformio/packages/tool-dfuutil/bin/dfu-suffix
Reason: tried: '/usr/local/opt/libusb/lib/libusb-1.0.0.dylib' (no such file), '/System/Volumes/Preboot/Cryptexes/OS/usr/local/opt/libusb/lib/libusb-1.0.0.dylib' (no such file), '/usr/local/opt/libusb/lib/libusb-1.0.0.dylib' (no such file), '/usr/local/lib/libusb-1.0.0.dylib' (no such file), '/usr/lib/libusb-1.0.0.dylib' (no such file, not in dyld cache)
*** [.pio/build/opta/firmware.bin] Error -6
========================================================================== [FAILED] Took 0.51 seconds ==========================================================================
* The terminal process "platformio 'run', '--target', 'upload', '--upload-port', '/dev/cu.usbmodem1101'" terminated with exit code: 1.
* Terminal will be reused by tasks, press any key to close it.
I did try brew install libusb but it made no difference.
The sketch is simply...
#include <Arduino.h>
/**
Getting Started with Opta™
Name: LED_Blink_Opta
Purpose: Blink STATUS LEDs on Opta™.
@author Arduino
*/
void setup() {
pinMode(LED_D0, OUTPUT);
pinMode(LED_D1, OUTPUT);
pinMode(LED_D2, OUTPUT);
pinMode(LED_D3, OUTPUT);
}
void loop() {
digitalWrite(LED_D0, HIGH);
delay(100);
digitalWrite(LED_D0, LOW);
delay(100);
digitalWrite(LED_D1, HIGH);
delay(100);
digitalWrite(LED_D1, LOW);
delay(100);
digitalWrite(LED_D2, HIGH);
delay(100);
digitalWrite(LED_D2, LOW);
delay(100);
digitalWrite(LED_D3, HIGH);
delay(100);
digitalWrite(LED_D3, LOW);
delay(500);
}
Thoughts?
opta-test % pio pkg install -g --tool "platformio/tool-dfuutil@^1.11.0"
Tool Manager: [email protected] is already installed
On a whim...
opta-test % pio pkg install -g --tool "platformio/tool-libusb"
Tool Manager: Installing platformio/tool-libusb
UnknownPackageError: Could not find the package with 'platformio/tool-libusb' requirements for your system 'darwin_arm64'
From "Verbose Upload"...
...a bunch of buildy stuff, then...
MethodWrapper(["checkprogsize"], [".pio/build/opta/firmware.elf"])
Advanced Memory Usage is available via "PlatformIO Home > Project Inspect"
RAM: [= ] 10.9% (used 57152 bytes from 523624 bytes)
Flash: [= ] 14.0% (used 109760 bytes from 786432 bytes)
.pio/build/opta/firmware.elf :
section size addr
.text 105648 134479872
.ARM.exidx 8 134585520
.data 4104 603979776
.uninitialized 24 603983880
.bss 53048 603983904
.heap 466088 604036952
.lwip_sec 278528 805306368
.ARM.attributes 44 0
.comment 156 0
.debug_frame 4188 0
.stab 60 0
.stabstr 118 0
Total 912014
arm-none-eabi-objcopy -O binary .pio/build/opta/firmware.elf .pio/build/opta/firmware.bin
"/Users/ken.martin/.platformio/packages/tool-dfuutil/bin/dfu-suffix" -v 0x2341 -p 0x0364 -d 0xffff -a .pio/build/opta/firmware.bin
dyld[7101]: Library not loaded: /usr/local/opt/libusb/lib/libusb-1.0.0.dylib
Referenced from: <2C64C116-83B7-3F20-B5BF-951356492177> /Users/ken.martin/.platformio/packages/tool-dfuutil/bin/dfu-suffix
Reason: tried: '/usr/local/opt/libusb/lib/libusb-1.0.0.dylib' (no such file), '/System/Volumes/Preboot/Cryptexes/OS/usr/local/opt/libusb/lib/libusb-1.0.0.dylib' (no such file), '/usr/local/opt/libusb/lib/libusb-1.0.0.dylib' (no such file), '/usr/local/lib/libusb-1.0.0.dylib' (no such file), '/usr/lib/libusb-1.0.0.dylib' (no such file, not in dyld cache)
*** [.pio/build/opta/firmware.bin] Error -6
=================================================================================== [FAILED] Took 5.49 seconds ===================================================================================
Tried manually config/make/installing libusb and I get...
'/usr/local/lib/libusb-1.0.0.dylib' (mach-o file, but is an incompatible architecture (have 'arm64', need 'x86_64')
Also tried coping the libusb files created by homebrew into the expected /usr/local/lib/ location... same result as above.
That's about all the thrashing I can think of right now. :)
Hi @papakpmartin, I've recently pushed a possible fix for your issue. Could you please the upstream version of the development platform (a Git client is required) ?
[env:opta]
platform = https://github.com/platformio/platform-ststm32.git
board = opta
framework = arduino
It worked!
I had tried going upstream at one point, so I did Uninstall the production and the upstream versions, then did a Full Clean (just to be sure). Then it built and uploaded!
FWIW, I realized this morning that the error is in the build, not upload, process. So presumably this is detectable/testable even if you don't have a Opta on hand.
Thanks so much for getting this figured out, @valeros!
I will not close this because I don't know how you want to handle that, project-wise.
@valeros Is this something that needs to be applied to other boards as well? I'm seeing exactly the same errors with black_f407ve and using platform = https://github.com/platformio/platform-ststm32.git in the env for that doesn't resolve the issue.
It looks like tool-dfuutil is still providing x86_64 binaries on M1/M2 systems, which cannot load the arm64 version of libusb-1.0.0.dylib that is installed with brew.
I believe I have the same issue, except with the RP2040 microcontroller. My combination is: macOS arm64 (13.5.2), VSCode (1.83.1), PlatformIO (Core 6.1.11, Home 3.4.4), Arduino framework, RP2040. I'm trying to program the Raspberry Pi Pico W using the Raspberry Pi Debug Probe (picoprobe).
It appears as if the compilation works, but on Upload I get same error message as OP:
dyld[51634]: Library not loaded: /usr/local/opt/libusb/lib/libusb-1.0.0.dylib
Config in platformio.ini
[env:pico-debug-tool]
framework = arduino
platform = https://github.com/maxgerhardt/platform-raspberrypi.git
board = rpipicow
board_build.core = earlephilhower
; Upload and debug over picoprobe
upload_protocol = picoprobe
;alt. upload_protocol = cmsis-dap
debug_tool = picoprobe
;alt. debug_tool = cmsis-dap
build_type = debug
I'm a bit slow/confused about what the solution was for @papakpmartin. Could it be similar for the platform in my case?
I believe I have the same issue, except with the RP2040 microcontroller.
This issue is specific to the stm32 platform using tool-dfuutil. You'll need to raise an issue for the raspberrypi platform: https://github.com/platformio/platform-raspberrypi/issues
For anyone else having this issue (Specifically on M1/M2 Mac), as a workaround you can run the following to get the required version of libusb until tool-dfuutil is fixed:
arch -x86_64 /bin/bash -c "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/master/install.sh)"
Followed by
arch -x86_64 /usr/local/bin/brew install libusb