painless-linux icon indicating copy to clipboard operation
painless-linux copied to clipboard

Published 20 hours ago • verified publisher icon natinusala

Repeated errors?

Open Weaselll opened this issue 7 years ago • 12 comments

I seem to repeatedly get both errors 31 and 995, even with redoing all the guide's steps. Would that be a problem on my end or are others getting this?

Weaselll avatar May 07 '18 23:05 Weaselll

Are you on Windows ? Error 31 is normal then - I don't know what error 995 is. On Windows I personnally have a 95% success rate.

Could you give me the full logs ?

natinusala avatar May 07 '18 23:05 natinusala

Put your Switch in RCM mode now TegraRcmSmash (64bit) 1.1.0-1 by rajkosto Opened USB device path \?\usb#vid_0955&pid_7321#5&1cbdcd65&0&3#{8618666a-1afa-4a7f-873d-6765dcf82cf3} RCM Device with id 4082FC0F00000008C4122E6401101062 initialized successfully! Uploading payload (mezzo size: 0, user size: 2364, total size: 29904, total padded size: 32768)... Switched to high buffer Smashing the stack! Smashed the stack with a 0x7000 byte SETUP request! Switching to sending of section 'CBFS' Sending 0x00007000 bytes from offset 0x00000000 Sending 0x00000004 bytes from offset 0x000ffffc Sending 0x00000020 bytes from offset 0x00020138 Sending 0x00000018 bytes from offset 0x00020100 Sending 0x00000020 bytes from offset 0x00020118 Sending 0x00000018 bytes from offset 0x00020180 Sending 0x00000020 bytes from offset 0x00020198 Sending 0x0000001c bytes from offset 0x000201b8 Sending 0x00005332 bytes from offset 0x000201d4 Sending 0x00100000 bytes from offset 0x00000000 Finished sending section 'CBFS' (total bytes sent: 1098722) Win32 error 995 during post-smash read op Done Press any key to continue . . .

Weaselll avatar May 07 '18 23:05 Weaselll

And yes I am on Windows.

Weaselll avatar May 07 '18 23:05 Weaselll

Post-smash errors are normal - Linux should boot shortly after the CBFS section has been sent regardless of what happens next.

natinusala avatar May 08 '18 00:05 natinusala

Linux boots SOMETIMES then goes to a black screen and stays.

Weaselll avatar May 08 '18 00:05 Weaselll

Is it a RCM black screen or just a black screen ?

natinusala avatar May 08 '18 00:05 natinusala

Just a black screen.

Weaselll avatar May 08 '18 00:05 Weaselll

I'd say it comes from your SD card, try with another one if you can

natinusala avatar May 08 '18 00:05 natinusala

Alright ill get back to you on that

Weaselll avatar May 08 '18 00:05 Weaselll

Still getting the same errors, even after changing sd cards.

Weaselll avatar May 08 '18 00:05 Weaselll

Update: tried with another switch and im getting consistent boot screens before going straight to black

Weaselll avatar May 08 '18 01:05 Weaselll

Without UART I'm afraid we won't be able to diagnose what's going on here

natinusala avatar May 08 '18 14:05 natinusala