operating-system
operating-system copied to clipboard
home-assistant
USB devices not available after update to 12.3 on Yellow. Also preventing boot.
Describe the issue you are experiencing
Updated Home Assistant OS from 12.2 to 12.3 on my Yellow and it did not come back online afterwards. After a manual reboot the Yellow is online again but all connected USB devices are missing.
When rebooting several times it seems there is a 50:50 chance it boots at all and if it boots, USB is missing.
Downgrade to 12.2 solves the issue.
What operating system image do you use?
yellow (Home Assistant Yellow)
What version of Home Assistant Operating System is installed?
12.3
Did you upgrade the Operating System.
Yes
Steps to reproduce the issue
Just update from 12.2 to 12.3
Anything in the Supervisor logs that might be useful for us?
Unfortunately too late since I already downgraded to 12.2 again.
Anything in the Host logs that might be useful for us?
Unfortunately too late since I already downgraded to 12.2 again.
System information
No response
Additional information
No response
Hm, I have two Yellow's here, and double checked, both run on HAOS 12.3 successfully, with USB devices detected.
What (type of) device is it which is missing?
The ha logs commands have a boot parameter nowadays which allow to get logs from previous boot, e.g.
ha host logs --boot -1 --lines 10000
Installed the update again. Host is pingable afterwards but connection on port 8123 is refused and SSH also not reachable. Powercycled Yellow and now online but this time USB devices (BLE dongle and Homematic RF dongle) are available.
OS Version: Home Assistant OS 12.3
Home Assistant Core: 2024.5.2
Home Assistant URL: http://homeassistant.local:8123
Observer URL: http://homeassistant.local:4357
~ # lsusb
Bus 001 Device 001: ID 1d6b:0002
Bus 001 Device 004: ID 2fe3:000b
Bus 001 Device 002: ID 1a40:0101
Bus 001 Device 003: ID 1b1f:c020
Previously (in the error case) it only showed a single USB device, which was
Bus 001 Device 001: ID 1d6b:0002
if I remember correctly.
Attached the result of ha host logs --boot -1 --lines 20000 , not sure if there is something visible in there:
boot.log.gz
Host is pingable afterwards but connection on port 8123 is refused and SSH also not reachable.
Hm, sounds like Core did not get started then :thinking: ha supervisor logs might be helpful in this case.
Ideally the host dmesg would be helpful here, especially in the non working case. It seems that too much got logged already, the log is not 2000 lines, and the first entry is a cleanup entry from journald :cry:
Seems 2fe3:000b is a Zephyr dev device? We did move to Linux 6.6 for Yellow with this release, the first time. We previously had quite some problems with some USB bus enumeration changes, however, from what I can tell most of them are reverted for Yellow as well (references https://github.com/home-assistant/operating-system/issues/2995 and https://github.com/home-assistant/operating-system/pull/3224).
If you can reproduce the problem, can you use dmesg in the SSH/Terminal?
Coincidentally, I had an nRF DK with the HCI firmware lying around, so I tried booting my Yellow with that. However, out of ~30 boots so far, I encountered the issue once along the first couple of tries and I can't trigger it again. The cause seems to be the same as in #2257, the USB hub is not enumerated because of an unhandled interrupt. Just like in https://github.com/raspberrypi/linux/issues/5064, it is a dwc2 USB interrupt:
[ 6.598626] dwc2 fe980000.usb: irq 41, io mem 0xfe980000
(...)
[ 7.331480] irq 41: nobody cared (try booting with the "irqpoll" option)
[ 7.338199] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G C 6.6.28-haos-raspi #1
[ 7.346551] Hardware name: Raspberry Pi Compute Module 4 Rev 1.0 (DT)
[ 7.350598] usb 1-1: new high-speed USB device number 2 using dwc2
[ 7.352982] Call trace:
[ 7.361598] dump_backtrace+0xa0/0x100
[ 7.365349] show_stack+0x20/0x38
[ 7.368659] dump_stack_lvl+0x48/0x60
[ 7.372319] dump_stack+0x18/0x28
[ 7.375628] __report_bad_irq+0x40/0xf0
[ 7.379461] note_interrupt+0x330/0x388
[ 7.383292] handle_irq_event+0xa4/0xc0
[ 7.387126] handle_fasteoi_irq+0xac/0x240
[ 7.391219] generic_handle_domain_irq+0x34/0x58
[ 7.395834] gic_handle_irq+0x4c/0xd8
[ 7.399491] call_on_irq_stack+0x24/0x58
[ 7.403411] do_interrupt_handler+0x88/0x98
[ 7.407591] el1_interrupt+0x34/0x68
[ 7.411162] el1h_64_irq_handler+0x18/0x28
[ 7.415255] el1h_64_irq+0x64/0x68
[ 7.418651] default_idle_call+0x5c/0x170
[ 7.422657] do_idle+0x204/0x238
[ 7.425884] cpu_startup_entry+0x40/0x50
[ 7.429804] rest_init+0xec/0xf8
[ 7.433028] arch_call_rest_init+0x18/0x20
[ 7.437122] start_kernel+0x528/0x670
[ 7.440780] __primary_switched+0xbc/0xd0
[ 7.444787] handlers:
[ 7.447053] [<0000000048434357>] dwc2_handle_common_intr [dwc2]
[ 7.452996] [<00000000d0dace6f>] dwc2_hsotg_irq [dwc2]
[ 7.458147] [<00000000a7d505ef>] usb_hcd_irq
[ 7.462417] Disabling IRQ #41
Attaching the full dmesg for reference: yellow-usb-fail-dmesg.txt
@mmarc can you try connecting your Yellow to a PC with USB-C connector switched to the USB-UART mode (see Linux/Mac or Windows instructions) and checking the boot log and dmesg directly there?
(Update 15 boots later - the issue occurred again with the same stack trace. rmmod dwc2 && modprobe dwc2 made the hub and attached device available again.)
I have two yellows, both with the same z-wave stick inserted. Have not updated the 2nd one yet, but the first one had the same issues here as described. Luckly for me, I have remote PoE power cycle capability, and was able to get it back online after a power cycle, with the z-wave stick. I have 3 more yellows in a box, I just need to assemble and test in the lab.
I just upgraded my Home Assistant Blue from 12.2 to 12.4 and am experiencing what may be the same issue. It's booted twice since the upgrade, both times the system came up fine, but my Zigbee USB stick (CC2652R1) was not detected.
Normally I'd expect my Zigbee stick to appear at /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0, but now I'm seeing no /dev/serial at all, and no /dev/ttyUSB* devices either.
Here's what lsusb sees.
~ lsusb
Bus 002 Device 007: ID 05e3:0620
Bus 001 Device 001: ID 1d6b:0002
Bus 001 Device 007: ID 05e3:0610
Bus 002 Device 001: ID 1d6b:0003
I believe those are all just the internal USB hubs.
There are no obvious errors in dmesg. In particular I do not see an unhandled interrupt message like @sairon is reporting.
Also nothing obvious in the supervisor or host logs.
When I unplug and re-plug the Zigbee stick, there are no messages in dmesg about anything being connected or disconnected.
Let me know if there's anything else I can usefully provide.
Downgrading to 12.2 did not fix the issue for me (even though that version was working fine before). I'm still observing the same symptoms. So I'm now less confident I have the same issue.
I thought perhaps the Zigbee stick was just broken, but I plugged it into my desktop and it connects as /dev/ttyUSB1 just fine there. I also tried pluggin into different USB ports on the HA Blue box, but no luck.
I looked at dmesg output again. Here's the section where it detects the USB hubs:
[ 1.557606] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2
[ 1.558017] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1
[ 1.565709] dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator
[ 1.570349] dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator
[ 1.577569] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM
[ 1.584812] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 1.589930] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 1.597605] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000008000000010
[ 1.606913] xhci-hcd xhci-hcd.0.auto: irq 26, io mem 0xff500000
[ 1.612790] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 1.618249] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 1.625878] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 1.632665] hub 1-0:1.0: USB hub found
[ 1.636112] hub 1-0:1.0: 2 ports detected
[ 1.640211] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.648309] hub 2-0:1.0: USB hub found
[ 1.651883] hub 2-0:1.0: 1 port detected
[ 1.655990] dwc3-meson-g12a ffe09000.usb: switching to Device Mode
The only thing that seems maybe suspicious is the "We don't know the algorithms for LPM for this host, disabling LPM" message, but I doubt that's related.
Today I tried updating to 13.1 in the hope that a more recent OS update would have fixed the issue. No luck. 13.1 is still not recognizing my USB device, with the same symptoms as 12.3.
Thanks stinks. I am on 13.1 and not having the issue this time. I am still using the HA Yellow PoE version
From: John Bytheway @.> Sent: Sunday, September 1, 2024 6:40 AM To: home-assistant/operating-system @.> Cc: Steven Hoggatt @.>; Comment @.> Subject: Re: [home-assistant/operating-system] USB devices not available after update to 12.3 on Yellow. Also preventing boot. (Issue #3347)
Today I tried updating to 13.1 in the hope that a more recent OS update would have fixed the issue. No luck. 13.1 is still not recognizing my USB device, with the same symptoms as 12.3.
— Reply to this email directly, view it on GitHubhttps://github.com/home-assistant/operating-system/issues/3347#issuecomment-2323301859, or unsubscribehttps://github.com/notifications/unsubscribe-auth/BDSYDQMNCFWVC4LSGLMWBKDZUL4JPAVCNFSM6AAAAABHNCZIYCVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGMRTGMYDCOBVHE. You are receiving this because you commented.Message ID: @.***>
I think my bug isn't really the same as the one originally reported here, so I opened #3573 instead of continuing to hijack this one.
Good luck sir.. at least downgrading is fairly painless
Get Outlook for Androidhttps://aka.ms/AAb9ysg
From: John Bytheway @.> Sent: Sunday, September 1, 2024 11:31:15 AM To: home-assistant/operating-system @.> Cc: Steven Hoggatt @.>; Comment @.> Subject: Re: [home-assistant/operating-system] USB devices not available after update to 12.3 on Yellow. Also preventing boot. (Issue #3347)
I think my bug isn't really the same as the one originally reported here, so I opened #3573https://github.com/home-assistant/operating-system/issues/3573 instead of continuing to hijack this one.
— Reply to this email directly, view it on GitHubhttps://github.com/home-assistant/operating-system/issues/3347#issuecomment-2323417042, or unsubscribehttps://github.com/notifications/unsubscribe-auth/BDSYDQPPEE72IJKR5Y5TZHLZUM6NHAVCNFSM6AAAAABHNCZIYCVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGMRTGQYTOMBUGI. You are receiving this because you commented.Message ID: @.***>