mfgtools
mfgtools copied to clipboard
NXPmicro
Frozen when flashing the image for IMX6DL
Hi
I tried to flash the latest image V5.15.32 for the board based on IMX6U7CVM08AC, using Ubuntu 22.04 with the *.wic.bz2 file
But It's frozen, here is the message in verbose mode:
vmuser@vmuser-virtual-machine:/mnt/hgfs/CODE$ uuu -v -b emmc_all u-boot-tagged.imx imx-image-full-imx6dlsabresd-20230131030147.rootfs.wic.bz2
uuu (Universal Update Utility) for nxp imx chips -- lib1.4.193
Build in config:
Pctl Chip Vid Pid BcdVersion
==================================================
SDPS: MX8QXP 0x1fc9 0x012f [0x0002..0xffff]
SDPS: MX8QM 0x1fc9 0x0129 [0x0002..0xffff]
SDPS: MX8DXL 0x1fc9 0x0147
SDPS: MX28 0x15a2 0x004f
SDPS: MX815 0x1fc9 0x013e
SDPS: MX865 0x1fc9 0x0146
SDPS: MX8ULP 0x1fc9 0x014a
SDPS: MX8ULP 0x1fc9 0x014b
SDP: MX7D 0x15a2 0x0076
SDP: MX6Q 0x15a2 0x0054
SDP: MX6D 0x15a2 0x0061
SDP: MX6SL 0x15a2 0x0063
SDP: MX6SX 0x15a2 0x0071
SDP: MX6UL 0x15a2 0x007d
SDP: MX6ULL 0x15a2 0x0080
SDP: MX6SLL 0x1fc9 0x0128
SDP: MX7ULP 0x1fc9 0x0126
SDP: MXRT106X 0x1fc9 0x0135
SDP: MX8MM 0x1fc9 0x0134
SDP: MX8MQ 0x1fc9 0x012b
SDPU: SPL 0x0525 0xb4a4 [0x0000..0x04ff]
SDPV: SPL1 0x0525 0xb4a4 [0x0500..0x9998]
SDPV: SPL1 0x1fc9 0x0151 [0x0500..0x9998]
SDPU: SPL 0x0525 0xb4a4 [0x9999..0x9999]
SDPU: SPL 0x3016 0x1001 [0x0000..0x04ff]
SDPV: SPL1 0x3016 0x1001 [0x0500..0x9998]
FBK: 0x066f 0x9afe
FBK: 0x066f 0x9bff
FBK: 0x1fc9 0x0153
FB: 0x0525 0xa4a5
FB: 0x18d1 0x0d02
FB: 0x3016 0x0001
FB: 0x1fc9 0x0152
Run built-in script:
uuu_version 1.4.149
# @_flash.bin | bootloader, which can extract from wic image
# @_image [_flash.bin] | wic image burn to emmc.
# This command will be run when i.MX6/7 i.MX8MM, i.MX8MQ
SDP: boot -f u-boot-tagged.imx -scanlimited 0x800000
# This command will be run when ROM support stream mode
# i.MX8QXP, i.MX8QM
SDPS: boot -scanterm -f u-boot-tagged.imx -scanlimited 0x800000
# These commands will be run when use SPL and will be skipped if no spl
# SDPU will be deprecated. please use SDPV instead of SDPU
# {
SDPU: delay 1000
SDPU: write -f u-boot-tagged.imx -offset 0x57c00
SDPU: jump -scanlimited 0x800000
# }
# These commands will be run when use SPL and will be skipped if no spl
# if (SPL support SDPV)
# {
SDPV: delay 1000
SDPV: write -f u-boot-tagged.imx -skipspl -scanterm -scanlimited 0x800000
SDPV: jump -scanlimited 0x800000
# }
FB: ucmd setenv fastboot_dev mmc
FB: ucmd setenv mmcdev ${emmc_dev}
FB: ucmd mmc dev ${emmc_dev}
FB: flash -raw2sparse all imx-image-full-imx6dlsabresd-20230131030147.rootfs.wic.bz2/*
FB: flash -scanterm -scanlimited 0x800000 bootloader u-boot-tagged.imx
FB: ucmd if env exists emmc_ack; then ; else setenv emmc_ack 0; fi;
FB: ucmd mmc partconf ${emmc_dev} ${emmc_ack} 1 0
FB: done
Wait for Known USB Device Appear...
New USB Device Attached at 3:2
3:2>Start Cmd:SDP: boot -f u-boot-tagged.imx -scanlimited 0x800000
100%3:2>Okay (3.501s)
What should I do for it?
But I flash the old image (4.1.15) with mfgtool is okay. is there some differents between the latest image (5.15.32) and the old one e.g. address?
I found the size of old u-boot (4.1.15) is about 367KB, and the latest one is 624KB.
The size is not problem. Maybe DDR change or some problem, uboot hange before print anything. It need debug uboot. Does it can boot from sd card?
uuu -b emmc old_uboot new_uboot
to check if new_uboot can boot from emmc?
I tried to make the SD card as following the guide from NXP to boot, but the unit didn't boot with this image from SD card, which can boot with the old image.
bzcat ...wic.bz2 || sudo dd of=/dev/sd.. bs=1M conv=fsync
OTOH, uuu -b emmc <old_uboot> <new_uboot> is also frozen on the same place.
I found some output from serial port using uuu command as you said on Windows.
U-Boot 2014.04-gd8ae003-dirty (Oct 26 2017 - 17:19:36)
CPU: Freescale i.MX6DL rev1.3 at 792 MHz
CPU: Temperature 57 C, calibration data: 0x59751f69
Reset cause: POR
Board: MX6-SabreSD
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
*** Warning - bad CRC, using default environment
No panel detected: default to Hannstar-XGA
Display: Hannstar-XGA (1024x768)
In: serial
Out: serial
Err: serial
DS2460'S ID is: 0x3c 0x9e 0xc2 0x81 0x00 0x00 0x00 0x44
normol mode!
mmc2(part 0) is current device
Net: Read MAC from ds2460 : 00:14:97:2e:88:fa
Phy not found
PHY reset timed out
FEC [PRIME]
Boot from USB for mfgtools
Use default environment for mfgtools
Run bootcmd_mfg: run mfgtool_args;bootz ${loadaddr} ${initrd_addr} ${fdt_addr};
Hit any key to stop autoboot: 0
Bad Linux ARM zImage magic!
you can ctrl-c, then enter console, run fastboot 0
If it works. It should failure auto run fastboot by detect boot from USB. if it is not works, it should usb related function does work.
run fastboot 0 or fastboot 0 doesn't work on the console.
=> run fastboot 0
## Error: "fastboot" not defined
=> fastboot 0
Unknown command 'fastboot' - try 'help'
=>
Your uboot missed some configuration. https://github.com/NXPmicro/mfgtools/wiki/uboot-config-requirement
Sorry for late.
I added the configuration following the website to .config file, but the uboot v2016.03 doesn't seem to have this fastboot function.
but I saw something about SPL but there is something different. It would be good if you could check it for me. The attach is the .config file after make mx6dlsabresd_defconfig.
#
# Boot images
#
CONFIG_SUPPORT_SPL=y
# CONFIG_SPL is not set
# CONFIG_FIT is not set
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sabresd/mx6dlsabresd.cfg,MX6DL,SYS_USE_SPINOR"